Open Die Forging Factory, Jiangyin, Jiangsu, China. Forged Rings, Flanges, Bars and Shafts. Tel 0086-189-2135-9659  |  sales@steelforgepieces.com
Jiangyin Jiangnan Metal Co., Ltd. Open Die Forgings | Seamless Rolled Rings | Forged Flanges

XM-29 Forgings, UNS S24000 / Nitronic 33

Open die forged rings, seamless rolled rings, flanges, round bars, shafts, discs, sleeves, bushings and tube sheets in nitrogen strengthened austenitic stainless steel.

XM-29 at a glance

XM-29 is the ASTM designation for UNS S24000, a nitrogen strengthened austenitic stainless steel with 17.00 to 19.00 % Cr, 11.50 to 14.50 % Mn, 2.25 to 3.75 % Ni and 0.20 to 0.40 % N. The same grade is sold under the trade name Nitronic 33 and by Carpenter Technology as 18Cr-3Ni-12Mn. Manganese and nitrogen take the place of most of the nickel used in Type 304, which gives an annealed yield strength about twice that of 304 together with good toughness, good ductility and very low magnetic permeability that is held after severe cold work and at cryogenic temperature.

Bar to ASTM A276 Type XM-29 must meet 100 ksi (690 MPa) tensile, 55 ksi (380 MPa) yield, 30 % elongation and 50 % reduction of area as minimum values. The grade hardens by cold work only and does not respond to thermal hardening.

Jiangyin Jiangnan Metal Co., Ltd. is an open die forging factory in Jiangyin, Jiangsu, China that makes XM-29 forgings to customer drawings, with forging stock ordered to ASTM A314. Enquiries go to sales@steelforgepieces.com or +86-189-2135-9659.

UNS numberS24000
ASTM designationXM-29
Trade namesNitronic 33, 18Cr-3Ni-12Mn
FamilyAustenitic, N strengthened
Yield, A276 bar, min380 MPa / 55 ksi
Tensile, A276 bar, min690 MPa / 100 ksi
Density7.775 g/cm³
Forging stock specASTM A314

Datasheet reviewed 11 October 2026 by the metallurgical department of Jiangyin Jiangnan Metal Co., Ltd.

1. What XM-29 is

XM-29 belongs to the Cr-Mn-N austenitic family. Instead of 8 to 10 % nickel, austenite is held stable by roughly 12 % manganese together with 0.20 to 0.40 % nitrogen in solid solution. Nitrogen is an effective strengthener, so the grade reaches its high yield strength in the annealed condition rather than through cold work or precipitation hardening. The manganese level raises hot ductility and allows the steel to dissolve more nitrogen than a conventional 18-8 composition can hold.

Because the austenite is stable, the structure does not transform to martensite under heavy deformation or at low temperature. That is the reason the grade keeps very low magnetic permeability after severe cold working and down to cryogenic temperature, and it is the property behind most non-magnetic applications.

Designation cross reference

Table 1. Names and specifications under which UNS S24000 is ordered.
Designation typeValue
UNSS24000
ASTM type symbolXM-29, tubular products TP XM-29
Trade nameNitronic 33
Producer designationCarpenter 18Cr-3Ni-12Mn
SAEXM-290
ASTM product specificationsA240 plate, sheet and strip; A276 bars and shapes; A249; A269; A312; A358; A412; A479; A580; A688; A813; A814
Forging stockASTM A314, stainless steel billets and bars for forging

2. Chemical composition of XM-29 (UNS S24000)

Table 2. Chemical composition in weight percent. Ranges are those allowed by the applicable ASTM specifications.
ElementContent (%)Function
Carbon, C0.08 maxHeld low to limit carbide precipitation
Silicon, Si0.75 max, 1.00 max in ASTM A276Deoxidiser
Manganese, Mn11.50 to 14.50Austenite stabiliser, raises nitrogen solubility and hot ductility
Phosphorus, P0.060 maxResidual
Sulfur, S0.030 maxResidual
Chromium, Cr17.00 to 19.00Passive film, corrosion resistance
Nickel, Ni2.25 to 3.75, listed as 2.3 to 3.7 in ASTM A276 and A240Austenite stability, toughness
Nitrogen, N0.20 to 0.40Main solid solution strengthener
Iron, FeBalanceBase

Forging stock is procured from EAF plus VOD or ESR melted heats. The melting route is stated on the mill certificate issued with every order.

3. Mechanical properties

3.1 Specified minimum values

Table 3. Minimum room temperature requirements in the solution annealed condition.
PropertyASTM A276 Type XM-29 bar, hot and cold finishedASTM A240 UNS S24000 plate
Tensile strength, min100 ksi (690 MPa)690 MPa
Yield strength, min55 ksi (380 MPa)415 MPa
Elongation in 2 in. or 4D, min30 %40 %
Reduction of area, min50 %not specified

3.2 Typical annealed values

Table 4. Representative annealed values. Results vary with section size, amount of hot work and test direction, so these figures are indicative and do not replace the order specification.
PropertyMetricImperial
Tensile strength689 MPa typical, up to about 770 MPa reported100 ksi, up to about 110 ksi
Yield strength, 0.2 % proof379 MPa typical, up to about 430 MPa reported55 ksi, up to about 63 ksi
Elongation at break in 2 in.39 to 40 %39 to 40 %
Reduction of areaabout 57 %about 57 %
Hardness, Brinell210 to 241 HB210 to 241 HB
Hardness, Rockwell B88 to 100 HRB88 to 100 HRB
Modulus of elasticity200 GPa29 x 106 psi
Shear modulus77 GPa11 x 106 psi
Shear strength530 MPa77 ksi
Fatigue strength370 MPa54 ksi
Poisson ratio0.280.28

4. Physical and thermal properties

Table 5. Physical and thermal data for UNS S24000.
PropertyMetricImperial
Density7.775 g/cm³0.2808 lb/in³
Thermal expansion coefficient, 26 to 93 C (78 to 200 F)16.074 µm/m·C8.93 µin/in·F
Specific heat capacity480 J/kg·K0.12 BTU/lb·F
Melting onset, solidus1350 C2460 F
Melting completion, liquidus1390 C2540 F
Latent heat of fusion280 J/gnot applicable
Magnetic permeabilityVery low, held after severe cold work and at cryogenic temperature

5. XM-29 compared with Type 304

XM-29 is superior to Type 304 in five specific points.

Nickel content of about 3 % instead of 8 to 10 % also keeps the grade less exposed to nickel price movement, and base metal cost is moderately low among wrought austenitic stainless steels.

6. Corrosion resistance and service limits

General corrosion resistance of XM-29 is superior to Type 409 and close to Type 304. In weak acid solutions it approaches 304. In more aggressive media it is somewhat less resistant than 304.

Service limit. Like most stainless steels, XM-29 is prone to pitting and crevice corrosion in seawater and other aggressive chloride media, and it should not be used in those conditions unless cathodically protected. For seawater, firewater, subsea pipework, risers and manifolds, specify a duplex or super duplex grade such as A182 F51, A182 F53 or A182 F55, or the 6Mo austenitic grade A182 F44. For hot sulphuric and mixed acid duty, consider Alloy 20, 904L or Hastelloy C-276. Our engineers can review the duty with you before the order is placed.

7. Forging, heat treatment and fabrication

7.1 Forging practice

The stock is heated to 1093 C (2000 F) and soaked until the section has equalized, then heated again to 1177 C (2150 F) and equalized before forging. The two stage heat avoids thermal gradients in heavy sections, and the high finishing temperature is needed because nitrogen strengthened austenite is considerably stiffer at temperature than 18-8 grades.

7.2 Solution annealing

After forging the parts are soaked at 1038 to 1121 C (1900 to 2050 F) and then rapidly quenched in water or air.

7.3 Forming, machining, welding and hardening

Table 6. Fabrication summary.
OperationPractice
FormingCommonly used forming methods apply. Process annealing at about 1065 C (1950 F) removes the stress that builds up because of the high work hardening rate.
MachiningSlow speeds, positive feeds and a resulphurised lubricant are recommended. Chips can be stringy and tough, so chip breakers or curlers are useful.
WeldingSubmerged arc welding, gas metal arc welding and gas tungsten arc welding are all used. The same equipment and techniques as conventional austenitic grades generally apply.
HardeningBy cold work only. The grade cannot be hardened by thermal treatment.

8. XM-29 forged product forms

All items below are produced by open die forging or ring rolling to the customer drawing, supplied solution annealed unless another condition is agreed.

Table 7. XM-29 forging programme. Send a drawing for confirmation of the size range available on our presses and ring mills.
Product formTypical use
Forged rings and seamless rolled ringsContainment rings, retaining rings, non-magnetic structural rings
Forged flanges and flange blanksPiping and pressure containing connections
Forged round bars, square bars and billetsMachining stock, fasteners, pins, valve stems
Forged shafts, spindles and eccentric shaftsRotating equipment that requires low magnetic permeability
Forged discs, disks and tube sheetsHeat exchanger and vessel internals
Forged sleeves, bushings and hollow barsWear and galling resistant bushings
Forged tubes, pipes and nozzlesTube assemblies and pipework components
Forged valve bodies, seat rings, blocks and valve partsBall, gate, globe, check and plug valves, strainers
Forged gears, rolls, wheels and manifoldsMechanical and structural components

9. Typical applications

Published applications for this grade include tube assemblies, pipes, cable, valves, tanks, containment rings and fans. In practice the grade is specified when a project needs a non-magnetic austenitic structure that survives heavy cold work, about double the annealed yield strength of 304 at a lower nickel content, dependable toughness at cryogenic temperature, or better galling and wear behaviour than standard austenitic grades.

Those requirements lead to forged XM-29 parts in cryogenic and liquefied gas equipment, generator and electrical hardware where magnetic permeability must stay low, bulk solid handling and screening equipment, hoppers, chutes and trailer bed liners where wear matters, wastewater and sewage treatment structures, and general mechanical and structural parts that need more strength than 304 can give. For chloride rich or seawater duty see the service limit in section 6.

10. Testing, inspection and certification

11. Frequently asked questions

What is XM-29 stainless steel?
XM-29 is the ASTM designation for UNS S24000, a nitrogen strengthened austenitic stainless steel with 17.00 to 19.00 % chromium, 11.50 to 14.50 % manganese, 2.25 to 3.75 % nickel and 0.20 to 0.40 % nitrogen. Manganese and nitrogen replace most of the nickel used in Type 304, and annealed yield strength is about twice that of 304.
Is XM-29 the same as Nitronic 33?
Yes. XM-29, UNS S24000 and Nitronic 33 all describe the same 18Cr-3Ni-12Mn nitrogen strengthened austenitic stainless steel. Carpenter Technology markets the same UNS S24000 composition as 18Cr-3Ni-12Mn.
What are the minimum mechanical properties of XM-29 bar?
To ASTM A276 Type XM-29, hot finished and cold finished bar must meet 100 ksi (690 MPa) tensile strength, 55 ksi (380 MPa) yield strength, 30 % elongation in 2 in. and 50 % reduction of area, all minimum. ASTM A240 plate in UNS S24000 requires 690 MPa tensile, 415 MPa yield and 40 % elongation minimum.
At what temperature is XM-29 forged?
Heat to 1093 C (2000 F) and soak to equalize, then heat again to 1177 C (2150 F), equalize and forge. Solution anneal afterwards at 1038 to 1121 C (1900 to 2050 F) and quench rapidly in water or air.
Can XM-29 be hardened by heat treatment?
No. It hardens by cold work only and does not respond to thermal hardening.
Is XM-29 magnetic?
Magnetic permeability stays very low even after severe cold working and at cryogenic temperature, which is a main reason the grade is chosen for non-magnetic parts.
Is XM-29 suitable for seawater or subsea service?
In general no. Corrosion resistance is close to Type 304 and better than 409, but the grade is prone to pitting and crevice corrosion in seawater and other aggressive chloride media and should not be used there unless cathodically protected. Duplex grades A182 F51, F53 and F55, or the 6Mo austenitic A182 F44, are the usual alternatives.
Which ASTM specifications cover XM-29?
A240, A249, A269, A276, A312, A358, A412, A479, A580, A688, A813 and A814 all list XM-29 or UNS S24000. Billets and bars for forging are ordered to ASTM A314.
What information is needed for a quotation?
A drawing or the rough dimensions, meaning OD x ID x height for rings and diameter x length for bars and shafts, plus quantity, governing specification and delivery condition, NDT and certification requirements, and the destination port. Send these to sales@steelforgepieces.com and we will reply with price and lead time.

Request a quotation for XM-29 forgings

Jiangyin Jiangnan Metal Co., Ltd., open die forging factory, Jiangyin, Jiangsu, China. Send a drawing or dimensions and we will quote XM-29 (UNS S24000 / Nitronic 33) rings, flanges, bars, shafts, discs and sleeves.

No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China

Other nitrogen strengthened and specialty stainless grades we forge: Nitronic 30, Nitronic 32, Nitronic 40, Nitronic 50, Nitronic 60, A182 F51, A182 F53, A182 F55, A182 F44, 904L and A286.

Data sources

Composition, mechanical, thermal and fabrication data on this page are taken from the ASTM A276 and ASTM A240 requirements for XM-29 and UNS S24000, from ASTM A314 for stainless billets and bars for forging, and from published Nitronic 33 and UNS S24000 datasheets. Figures are indicative and do not replace the full specification or the mill certificate for a particular heat. Confirm requirements with our engineering department before ordering.