Jiangyin Jiangnan Metal Co., Ltd. | Open Die Forging Factory 0086-189-2135-9659  |  sales@steelforgepieces.com

Home › Stainless Steel › X3CrNiMo17-13-3 (1.4436)

X3CrNiMo17-13-3 (EN 1.4436) Open Die Forgings

Forged rings, seamless rolled rings, flanges, shafts, discs, sleeves, bushings, tube sheets and bars, produced to drawing by Jiangyin Jiangnan Metal Co., Ltd., Jiangsu, China.

X3CrNiMo17-13-3, material number 1.4436, is a molybdenum alloyed austenitic chromium nickel stainless steel listed in EN 10088-3. It is held to max 0.05 % C, 16.5 to 18.5 % Cr, 10.5 to 13.0 % Ni and 2.50 to 3.00 % Mo. The grade is a more highly alloyed version of 1.4401 and is specified where the corrosion resistance of 1.4401 is no longer sufficient, in particular in chloride bearing media. PREN is 24.75 to 30.16. It is forged between 1200 and 900 C, solution annealed at 1020 to 1120 C with rapid cooling, and is non-magnetic, suited to cryogenic service and usable up to about 700 C.

Two limits govern selection. 1.4436 is not resistant to sea water, and the permitted carbon content means it is not rated resistant to intergranular corrosion in the welded condition.

Material No.1.4436
TypeAustenitic Cr-Ni-Mo stainless
Molybdenum2.50 to 3.00 %
PREN24.75 to 30.16
Rm, solution annealed500 to 700 MPa
Max service temperatureapprox. 700 C

1. Chemical composition to EN 10088-3

X3CrNiMo17-13-3 / 1.4436, % by mass, maximum unless a range is given
CSiMnPSNCrMoNi
0.051.002.000.0450.0300.1116.5 / 18.52.50 / 3.0010.5 / 13.0

Position within the 316 family

Carbon, molybdenum and nickel limits of neighbouring EN grades
GradeNo.C maxMo %Ni %Note
X5CrNiMo17-12-21.44010.072.00 / 2.5010.0 / 13.0Standard 316
X2CrNiMo17-12-21.44040.0302.00 / 2.5010.0 / 13.0316L, welded service
X3CrNiMo17-13-31.44360.052.50 / 3.0010.5 / 13.0Higher Mo, better pitting resistance
X2CrNiMo17-12-31.44320.0302.50 / 3.0010.5 / 13.0Low carbon version of 1.4436
X2CrNiMo18-14-31.44350.0302.50 / 3.0012.5 / 15.0Higher Ni, hygienic service

Where a specification calls for 1.4436 but the part will be welded and then exposed, 1.4432 holds the same molybdenum level at 0.030 % C. We forge both.

2. Mechanical properties, solution annealed

Longitudinal test direction, solution annealed condition
PropertySpecifiedTypical
Proof strength Rp0.2min 200 N/mm²370 N/mm²
Tensile strength Rm500 to 700 N/mm²670 N/mm²
Elongation A5min 40 %46 %
Hardnessmax 215 HB200 HB
Impact energy, ISO-V at 25 Cmin 100 J220 J
Rm by delivery condition+A: 500 to 730 MPa  |  +AT: 510 to 710 MPa
Modulus of elasticity190 to 215 GPa

Section size and delivery condition govern acceptance. Values are certified against the ordered specification.

Physical properties

DensityThermal conductivity at 20 CSpecific heat at 20 CElectrical resistivity at 20 CMagnetisable
8 kg/dm³15 W/m·K500 J/kg·K0.75 ohm·mm²/mNo, mur max 1.3
Mean coefficient of thermal expansion, 10-6 K-1
20 to 100 C20 to 200 C20 to 300 C20 to 400 C20 to 500 C
16.016.517.017.518.0

3. Forging and heat treatment

Pre-heat1150 to 1200 C
Forging range1200 to 900 C, hot forming also quoted 1150 to 850 C
Cooling after forgingRapid, air or water
Solution anneal (+AT)1020 to 1120 C, rapid cool

Rapid cooling after forging and after annealing is not optional. Slow cooling through the sensitisation range forms phases that reduce corrosion resistance and mechanical properties. EN guidance narrows the annealing window to 1030 to 1110 C. Where hot forming finishes above the solution annealing range, 1000 C is accepted as a lower limit for steels carrying up to 3 % Mo.

Machining and welding

Machinability is rated average and the grade is harder to machine than 1.4401 or 1.4435. With coated carbide tooling in the solution annealed condition at Rm 560 to 640 N/mm², guideline cutting speeds are about 115 m/min at 6 mm depth of cut and 0.5 mm/rev, 145 m/min at 3 mm and 0.4 mm/rev, and 185 m/min at 1 mm and 0.2 mm/rev. The grade welds by all common processes with interpass temperature held at 150 C maximum and no mandatory post weld heat treatment. Scale and heat tint are removed mechanically or by pickling and the surface is then passivated.

Selection limits. 1.4436 performs well in most natural waters, in food, beverage and agricultural duty and in a range of acids. It is not resistant to sea water. It is not rated resistant to intergranular corrosion in the welded condition because of its carbon content, although thin sections can be welded without that risk. Send us the medium, chloride level and operating temperature and we will confirm the grade before the order is placed.

4. Standards and international designations

Standards in which 1.4436 appears
StandardScope
EN 10250-4Open die steel forgings for general engineering purposes, stainless steels
EN 10222-5Steel forgings for pressure purposes, stainless steels
EN 10088-1 / 10088-3List of stainless steels; bars, rods, sections, semi-finished products
EN 10272Stainless steel bars for pressure purposes
EN 10028-7Flat products of steels for pressure purposes
EN 10216-5 / 10217-7Seamless and welded tubes for pressure purposes
EN 10253-3 / 10253-4Butt welding pipe fittings
Nearest designations in other systems, for guidance
SystemDesignation
EN / DIN, Werkstoff1.4436, X3CrNiMo17-13-3
USA, AISI / UNS316 / S31600, approximate, Mo range differs
UK, BS316 S13
France, AFNORZ7CND 18-12-03
Sweden, SIS2343
Japan, JISSUS 316
China, GB0Cr17Ni12Mo2

Equivalence tables match chemistry and properties approximately and do not replace the governing specification. Order against the EN number and the certificate will be issued against it.

5. Forged products supplied in this grade

RingsForged rings and seamless rolled rings, including heavy wall and deep sections
Flanges and tube sheetsForged flanges, tube sheets, nozzles and blanks for pressure equipment
Shafts and barsForged shafts, eccentric shafts, spindles, round bars, gear blanks
Discs and hollowsDiscs, sleeves, bushings, forged tubes and pipes
Valve componentsBodies, stems, seat rings and blocks for ball, gate, globe, check and plug valves
Custom workManifolds, wheels, crankshafts and other open die pieces to drawing

Typical service

Reported applications for the grade include medical, pharmaceutical and petrochemical equipment. In our order book, 1.4436 forgings go into chemical process plant, heat exchangers, condensers and evaporators, pressure vessels, columns and towers, pulp, paper and textile plant, compressor and power transmission parts, and valve and wellhead components. The grade is usually chosen at the point where chloride loading has passed what 1.4401 will take but has not reached the level that calls for a duplex or super austenitic steel.

Quality, testing and certification

Melting routes include EAF plus VOD, and ESR remelting where the specification calls for it. Forgings are supplied solution annealed. Ultrasonic testing is carried out to EN 10228-3, SEP 1921 or ASTM A388 as agreed at order stage. Certificates are issued to EN 10204 3.1, or 3.2 with third party inspection. Rough machined, proof machined and finish machined deliveries are available, with dimensional reports, PMI and corrosion testing on request.

Request a quotation

Send the drawing, or the outline dimensions, quantity, standard and test scope. We quote open die forgings and seamless rolled rings in 1.4436 and across the 316 family.

Jiangyin Jiangnan Metal Co., Ltd.
No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China

0086-189-2135-9659 sales@steelforgepieces.com

6. Common questions

What is the chemical composition of X3CrNiMo17-13-3?
To EN 10088-3, % by mass, maximum unless a range is given: C 0.05, Si 1.00, Mn 2.00, P 0.045, S 0.030, N 0.11, Cr 16.5 to 18.5, Mo 2.50 to 3.00, Ni 10.5 to 13.0. PREN is 24.75 to 30.16.
Is X3CrNiMo17-13-3 the same as 316 stainless steel?
It sits in the 316 family and is commonly cross referenced to AISI 316 and UNS S31600, whose average composition is close. The two are not interchangeable on paper. EN 10088-3 gives 1.4436 a molybdenum range of 2.50 to 3.00 %, above the 2.00 to 2.50 % of 1.4401, which is the grade normally treated as the direct 316 equivalent.
Why specify 1.4436 instead of 1.4401?
1.4436 is the more highly alloyed of the two and is used where the corrosion resistance of 1.4401 is no longer sufficient. The extra molybdenum gives slightly better resistance in chloride bearing media, reflected in a PREN of 24.75 to 30.16.
What are the forging and annealing temperatures?
Pre-heat to 1150 to 1200 C, forge between 1200 and 900 C, cool rapidly in air or water. Solution anneal at 1020 to 1120 C with rapid cooling, narrowed by EN guidance to 1030 to 1110 C.
Can 1.4436 be used in sea water?
No. Mill data states that the grade is not resistant to sea water. For sea water, brine and high chloride duty the usual alternatives are super austenitic 1.4547 and duplex grades 1.4462 and 1.4410, which we also forge.
Is it suitable for cryogenic or elevated temperature work?
It is suited to cryogenic applications and to service up to about 700 C, and it is non-magnetic at mur max 1.3. Elevated temperature properties are close to those of 1.4401. It is not a creep optimised grade; for sustained high temperature strength the H grades such as 316H and 347H are the correct selection.
Which standards cover X3CrNiMo17-13-3 forgings?
EN 10250-4 covers open die steel forgings for general engineering purposes in stainless steels, and EN 10222-5 covers steel forgings for pressure purposes. The grade is also listed in EN 10088-1 and EN 10088-3, EN 10272, EN 10028-7, EN 10216-5, EN 10217-7, EN 10253-3 and EN 10253-4.
Who supplies X3CrNiMo17-13-3 open die forgings?
Jiangyin Jiangnan Metal Co., Ltd., an open die forging factory at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China, produces 1.4436 forged rings, seamless rolled rings, flanges, shafts, discs, sleeves, bushings and tube sheets to customer drawing, with EN 10204 3.1 or 3.2 certification. Telephone 0086-189-2135-9659, e-mail sales@steelforgepieces.com.

7. Related grades

A182-F321 A182-F347 A182-F309 AISI 321H AISI 347H 904L A182-F44 A182-F51 A182-F53 A182-F55 A182-F61 Sanicro 28 Nitronic 50 Nitronic 60 17-4PH

Data compiled from EN 10088-1 and EN 10088-3, EN 10222-5, EN 10250-4 and published mill datasheets for material number 1.4436. Figures are for guidance. The purchase specification and the material certificate take precedence. Page maintained by the engineering department of Jiangyin Jiangnan Metal Co., Ltd. Last reviewed 9 October 2026.