Open-Die Forging Factory, Jiangyin, Jiangsu, China Tel 0086-189-2135-9659 Email sales@steelforgepieces.com
Jiangyin Jiangnan Metal Co., Ltd.Forged Rings, Flanges, Shafts, Seamless Rolled Rings Send Drawing for Quotation

Home › Stainless Steel › X2CrNiMoN25-7-4

X2CrNiMoN25-7-4 (1.4410 / UNS S32750) Super Duplex Forgings

Forged rings, seamless rolled rings, flanges, shafts, discs, sleeves and bars produced to drawing by Jiangyin Jiangnan Metal Co., Ltd., China.

X2CrNiMoN25-7-4 is the EN designation, material number 1.4410, of a 25 % chromium super duplex stainless steel. It corresponds to UNS S32750 and is ordered as forgings under ASTM and ASME A182 Grade F53. The austenitic-ferritic structure gives a minimum 0.2 % proof stress of 550 MPa, roughly double that of 316L, together with a PREN near 42. It is used where warm chloride-bearing media attack standard austenitic grades, at service temperatures below about 300 °C.

EN number1.4410
UNSS32750
Forging gradeA182 F53
PREN42
Rp0.2 min550 MPa
Density7.81 kg/dm³

1. Designations and governing standards

Table 1. Equivalent designations for X2CrNiMoN25-7-4
SystemDesignation
EN name and numberX2CrNiMoN25-7-4 / 1.4410
UNSS32750
ASTM and ASME forgingsA182 and SA-182 Grade F53
ASTM barA276, A479
ASTM plateA240
Trade name in common useSuper duplex 2507, Alloy 2507
ASME welding classificationP-No. 10H, Group No. 1
Sour serviceListed in NACE MR0175 / ISO 15156

European standards covering the grade include EN 10088-1, EN 10088-2 and EN 10088-3 for general purposes, EN 10222-5 for steel forgings for pressure purposes, EN 10028-7 for flat pressure products, EN 10216-5 and EN 10217-7 for tube, EN 10253-3 and EN 10253-4 for butt-welding fittings, and EN 10088-4 and EN 10088-5 for construction purposes. State on the order which standard governs, since the acceptance criteria for forgings under EN 10222-5 and under A182 F53 are not identical.

2. Chemical composition

Table 2. Chemical composition of 1.4410 and S32750, percent by mass
LimitCSiMnPSCrNiMoNCu
Min-----24.006.003.000.24-
Max0.0300.801.200.0350.01526.008.004.500.320.50

Limits in accordance with EN 10088-2 and ASME SA-240. Balance iron. Where dual certification to both the EN and the ASTM designation is required, say so at enquiry stage so that the melt is checked against both sets of limits before casting. PREN is calculated as %Cr + 3.3 x %Mo + 16 x %N and gives approximately 42 for this chemistry.

3. Mechanical properties

Table 3. Room temperature properties in the solution annealed condition
BasisRp0.2 minRmElongation minImpact KV, transverseHardness
EN 10088-2, plate up to 75 mm550 MPa795 to 930 MPa20 %60 J-
EN 10088-2, hot rolled strip530 MPa750 to 1000 MPa20 %60 J-
ASTM basis, S3275080 ksi, 550 MPa116 ksi, 800 MPa min15 %-32 HRC max

The two-phase structure and the high nitrogen content put the mechanical properties 50 to 100 % above most austenitic stainless steels. In practice this allows a wall thickness or a section size to be cut back against an equivalent 316L or 904L design, which often recovers the price difference in the finished assembly.

Table 4. Minimum elevated temperature properties
TemperatureTensile strength0.2 % yield strength
100 °C (212 °F)99 ksi, about 683 MPa65 ksi, about 448 MPa
200 °C (392 °F)93 ksi, about 641 MPa58 ksi, about 400 MPa
250 °C (482 °F)91 ksi, about 627 MPa55 ksi, about 379 MPa

Published values are in ksi and degrees Fahrenheit. Metric figures are converted.

4. Physical properties at 20 °C

Table 5. Physical data for 1.4410
DensityModulus of elasticitySpecific heatThermal conductivityElectrical resistivity
7.81 kg/dm³200 GPa0.50 J/g·K14.2 W/m·K0.80 Ω·mm²/m

Thermal conductivity is higher and the coefficient of thermal expansion lower than in the austenitic grades, which matters in tube sheets and heat exchanger bodies where differential expansion drives leakage at the joints.

5. Corrosion resistance

Table 6. Pitting resistance benchmark
AlloyPRENCritical pitting temperature
2507, S32750, 1.44104285 °C (185 °F)
2205 duplex3549 °C (120 °F)
316L2418 °C (64 °F)

Chromium, molybdenum and nitrogen at these levels give chloride pitting and crevice corrosion resistance on a par with the 6 % molybdenum austenitic alloys. Resistance to chloride stress corrosion cracking is high, which is the main reason the grade displaces 304 and 316 in warm seawater duty. In the solution annealed and quenched condition the material is resistant to intergranular corrosion. General corrosion resistance is good across the fields where the grade is normally specified, namely chemical plant, oil and gas, offshore, pulp and textile processing, and food production.

Service temperature is the limiting factor. Like all duplex grades, 1.4410 precipitates embrittling secondary phases on prolonged exposure to heat, so applications are kept below about 300 °C (600 °F).

6. Forging and heat treatment at our works

Material is melted by EAF with AOD or VOD refining, and ESR remelted stock is used where the specification or the end user calls for it. Forging is carried out on hydraulic presses and on radial-axial ring rolling mills.

  • Hot forging range. Approximately 1200 °C down to a 1025 °C finish. Most producers set the maximum hot working temperature between 1100 and 1150 °C. Hot strength is low, so reduction per pass is controlled and large rings are supported during handling.
  • Solution annealing. Minimum 1050 °C (1925 °F), normally held in the 1040 to 1120 °C band, after any hot or cold forming operation.
  • Quenching. Immediate rapid quench in water or forced air. Slow cooling through the 600 to 1000 °C range is avoided because it is where sigma phase forms.
  • Phase balance. Ferrite content checked by point count to ASTM E562 on request.
  • Surface condition. Pickled and rinsed after heat treatment where maximum corrosion resistance is required. Machined, rough turned or black as forged on request.

Machining and welding

Tooling data has to be adjusted against austenitic practice. With coated cemented carbide tools the cutting speed is cut back substantially compared with 316 and 316L, while feed is reduced only slightly, and the set-up needs to be rigid with positive chip control. For welding, the standard consumables are E2594 covered electrodes and ER2594 filler wire. Gas shielded, arc and resistance welding processes are all applicable. The weldment is solution annealed and quenched again where the fabrication sequence allows it.

7. Product forms supplied in X2CrNiMoN25-7-4

  • Seamless rolled rings and forged rings
  • Forged flanges: weld neck, slip-on, blind, orifice and non-standard profiles
  • Forged shafts, eccentric shafts and spindles
  • Forged discs, disks and gear blanks
  • Forged round bars, square blocks and step shafts
  • Forged sleeves, bushings, hollow bars, forged tubes and pipe sections
  • Forged tube sheets, nozzles, valve bodies, valve seat rings and valve stems
  • Forged wheels, manifolds, rolls and crankshafts

Dimensions are produced to customer drawing. Maximum single piece weight and maximum ring diameter are confirmed against the drawing at enquiry stage.

8. Typical applications

Offshore oil and gas

Downhole equipment, firewater and process water systems, injection and ballast water systems, subsea and deepwater production hardware, platform piping.

Chemical process plant

Pressure vessel components, piping, heat exchangers, tube sheets, liquor and storage tanks, separator internals.

Seawater and desalination

Desalination plant, high pressure reverse osmosis trains, seawater piping and pump components.

Valves and flow control

Stems, bodies, seat rings, blocks and discs for ball, gate, globe, check, plug valves and strainers.

Pulp and paper

Digesters, liquor tanks and paper machine parts.

Power and rotating equipment

Flue gas desulphurisation systems, compressor and gearbox parts, pump shafts and sleeves, nitrogen generators.

9. Testing, inspection and certification

  • Chemical analysis by spectrometer, heat analysis and product analysis
  • Tensile test, Charpy V-notch impact including low temperature, hardness
  • Corrosion testing on request to ASTM A923 for detrimental intermetallic phase and ASTM G48 ferric chloride pitting
  • Microstructure examination and ferrite count to ASTM E562
  • Ultrasonic testing to EN 10228-3, SEP 1921 or ASTM A388, with penetrant or magnetic particle testing as required
  • Certificate to EN 10204 3.1, or 3.2 with third party inspection by TUV, BV, LR, DNV or SGS

10. Frequently asked questions

What is X2CrNiMoN25-7-4 equivalent to?

It is EN 1.4410 and corresponds to UNS S32750, sold commercially as super duplex 2507. Forgings are ordered to ASTM or ASME A182 Grade F53, bar to A276 and A479, plate to A240.

What is the PREN of X2CrNiMoN25-7-4?

About 42, with a critical pitting temperature near 85 °C (185 °F). For comparison, 2205 duplex is PREN 35 at 49 °C and 316L is PREN 24 at 18 °C.

At what temperature is it forged and solution annealed?

Forged between roughly 1200 °C and 1025 °C, with maximum hot forming normally 1100 to 1150 °C. Solution annealed at a minimum of 1050 °C (1925 °F), typically 1040 to 1120 °C, then quenched immediately.

What is the maximum service temperature?

Below about 300 °C (600 °F). Above that, secondary phases form and reduce both toughness and corrosion resistance.

What is the difference between F53 and F55?

Both are super duplex forging grades within ASTM A182. F53 is the 25Cr 7Ni 4Mo chemistry of UNS S32750 and 1.4410 described on this page. F55 is UNS S32760, a tungsten and copper bearing super duplex with a different PREN formula that credits tungsten. Both are produced here. See the A182 F55 page.

Can 1.4410 be used in sour service?

UNS S32750 is listed within NACE MR0175 and ISO 15156, subject to the environmental limits, hardness caps and heat treatment conditions given in that standard for the relevant material group. Confirm the hydrogen sulphide partial pressure, chloride content, pH and temperature of the service with the end user before ordering.

Why must super duplex forgings be quenched immediately after annealing?

Slow cooling from the annealing temperature allows sigma and other intermetallic phases to precipitate between roughly 600 and 1000 °C. Those phases cut impact toughness and pitting resistance sharply. A minimum 1050 °C soak followed by a rapid quench preserves the balanced two-phase structure.

What lead time and minimum order apply?

Open-die forgings are made to order and there is no catalogue minimum. Single prototype pieces are accepted. Lead time depends on material availability, forged weight and the heat treatment and testing scope. Send the drawing for a firm schedule.

Request a quotation for X2CrNiMoN25-7-4 forgings

Send the drawing or a dimensioned sketch, the quantity, and the governing specification, for example EN 10222-5 or ASTM A182 F53. You will receive forged weight, delivery condition, testing scope, price and schedule.

Jiangyin Jiangnan Metal Co., Ltd. Open-Die Forging Factory
No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Tel 0086-189-2135-9659  |  Email sales@steelforgepieces.com

Email your drawing

Technical data compiled from EN 10088-2 and EN 10088-3 limit values, ASME SA-240, and published producer data sheets for UNS S32750. Figures are given for guidance and do not constitute a guarantee of properties for a particular application. Maintained by the technical department of Jiangyin Jiangnan Metal Co., Ltd.