Jiangyin Jiangnan Metal Co., Ltd.Open-Die Forging Factory, Jiangsu, China

Home › Stainless Steel › X2CrNiMoN18-12-4

X2CrNiMoN18-12-4 Forgings (EN 1.4434 / UNS S31753 / 317LN)

Nitrogen-alloyed austenitic stainless steel. Seamless rolled rings, forged flanges, shafts, discs, sleeves, tube sheets and round bars, produced to drawing by Jiangyin Jiangnan Metal Co., Ltd.

  • Material No. 1.4434
  • UNS S31753
  • AISI 317LN
  • JIS SUS 317LN
  • GB 022Cr19Ni13Mo4N
  • PREN about 32

X2CrNiMoN18-12-4 (material number 1.4434) is a low-carbon, nitrogen-alloyed austenitic stainless steel standardised in EN 10088-1, EN 10088-2 and EN 10028-7. Its 3.0 to 4.0 percent molybdenum and 0.10 to 0.20 percent nitrogen give better pitting and crevice resistance than 316L and a higher proof strength than 317L, while the 0.030 percent carbon ceiling keeps it resistant to sensitisation after welding. The grade is equivalent to AISI 317LN and UNS S31753. Jiangyin Jiangnan Metal Co., Ltd., an open-die forging factory in Jiangyin, Jiangsu, China, supplies it as custom forgings with EN 10204 3.1 or 3.2 certification.

1. Forgings produced in this grade

All parts are made to the customer drawing or dimension list. There is no fixed catalogue. If your part is not listed, send the drawing and we will confirm it against our press and ring-mill capacity.

Product forms available in X2CrNiMoN18-12-4 / 1.4434
CategoryForged itemsTypical destination
RingsSeamless rolled rings, forged rings, retaining rings, valve seat ringsPressure vessels, columns, towers, flanged joints
Flanges and closuresForged flanges, blind flanges, nozzles, tube sheets, manifoldsShell and tube heat exchangers, air receivers, reactors
Round sectionsForged round bars, blocks, billets, forged pipes and tubes, sleeves, bushingsMachining stock, pump and valve bodies
Rotating partsForged shafts, eccentric shafts, spindles, crankshafts, gears, rollsAgitators, gearboxes, compressors, power transmission
Flat sectionsForged discs, disks, wheels, hubs, platesValve internals, closure heads, process modules

2. Chemical composition of X2CrNiMoN18-12-4 (1.4434)

The figures below are the cast analysis limits given in EN 10088-2 for steel number 1.4434, in percent by mass. EN 10028-7, covering flat products for pressure purposes, specifies the same ranges.

EN 10088-2 cast analysis, percent by mass. Single values are maxima.
ElementMinMaxFunction
Carbon (C)-0.030Held low to resist sensitisation and intergranular attack after welding
Silicon (Si)-1.00Deoxidiser
Manganese (Mn)-2.00Austenite stabiliser, raises nitrogen solubility
Phosphorus (P)-0.045Residual, restricted
Sulphur (S)-0.015Residual, restricted for hot workability
Chromium (Cr)16.519.5Forms the passive film
Nickel (Ni)10.514.0Austenite stability, acid and stress corrosion resistance
Molybdenum (Mo)3.04.0Chloride pitting and crevice resistance, the main gain over 316L
Nitrogen (N)0.100.20Raises proof strength and reinforces pitting resistance
Iron (Fe)Balance
Ordering note. Several datasheets circulate a typical analysis of 18.2 Cr, 14 Ni, 4.2 Mo for 317LN. A molybdenum level of 4.2 percent sits outside the EN 10088-2 limit of 4.0 percent maximum for 1.4434. When ordering to EN, qualify the heat against the range in the table above rather than against a nominal figure. Where a buyer needs a narrower internal window, for example Mo at 3.5 percent minimum to lift PREN, we can restrict the melt aim on request.

Pitting resistance equivalent number

Calculated PREN for X2CrNiMoN18-12-4 is about 32, which places it between standard 316L and the 6 percent molybdenum superaustenitics. PREN is a comparative index only. It does not replace corrosion testing in your service chemistry, and real performance depends on temperature, chloride level, pH and surface finish.

3. Mechanical properties

Minimum values specified by EN 10028-7 in the solution annealed condition (+AT). For a forging, acceptance values are agreed at order stage against the governing standard, commonly EN 10250-4 for open-die stainless forgings or EN 10272 for bars for pressure purposes.

EN 10028-7 minimum properties, solution annealed (+AT)
Product formTensile Rm (MPa)Rp0.2 min (MPa)Rp1.0 min (MPa)Elongation A min (%)
Hot rolled plate, t up to 75 mm540 to 74027031040
Hot rolled strip, t up to 12 mm570 to 77027031035
Cold rolled strip, t up to 6 mm570 to 77029032035

Charpy V-notch impact energy to the same standard is 100 J minimum longitudinal and 60 J minimum transverse at 20 degrees C, and 60 J minimum transverse at minus 196 degrees C. That is why the grade is accepted for cryogenic structures as well as ambient process equipment.

Typical values, solution annealed

Tensile strengthabout 660 MPa
0.2 percent proof strengthabout 310 MPa
Elongation at breakabout 41 percent
Charpy V-notchabout 90 J
Brinell hardnessabout 200 HB
Fatigue strengthabout 270 MPa

Typical values describe the grade. They are not guaranteed minima. Acceptance is always against the ordered standard.

Physical properties

Density7.9 to 8.0 g/cm3
Modulus of elasticity200 GPa (29 x 106 psi)
Shear modulusabout 79 GPa
Poisson ratioabout 0.28
Thermal conductivityabout 15 W/m.K
Specific heat capacityabout 470 J/kg.K
Thermal expansionabout 16 micrometre/m.K
Melting rangeabout 1400 to 1450 degrees C
Magnetic responseNon-magnetic when annealed

4. Equivalent grades and governing standards

Cross-reference for X2CrNiMoN18-12-4
Region or bodyDesignation
EN steel nameX2CrNiMoN18-12-4
EN material number1.4434
USA, AISI and ASTM317LN, ASTM A240 Type 317LN
USA, UNSS31753
Japan, JISSUS 317LN
South Korea, KSSTS 317LN
China, GB022Cr19Ni13Mo4N
ISO 155104434-317-53-I
Standards that list 1.4434
StandardScope
EN 10088-1List of stainless steels
EN 10088-2Sheet, plate and strip for general purposes
EN 10088-3Semi-finished products, bars, rods and sections
EN 10028-7Flat products for pressure purposes, stainless steels
EN 10272Stainless steel bars for pressure purposes
EN 10250-4Open-die steel forgings for general engineering, stainless steels
ISO 9328-7 and ISO 15510International equivalents
AD 2000-Merkblatt W 2German pressure equipment material approval
1.4434 is not 1.4439. X2CrNiMoN17-13-5 (1.4439) is a separate, higher molybdenum grade corresponding to 317LMN and UNS S31726. If your specification calls for 317LMN rather than 317LN, you need 1.4439. Tell us and we will quote that grade instead.

5. How we make these forgings

Melting route

The grade is processed by EAF with VOD refining, with ESR remelting available where the buyer requires improved cleanliness, tighter segregation control or better transverse properties in heavy sections. The route is fixed at order confirmation and stated on the mill certificate.

Hot working

Open-die forging is carried out in the austenitic hot working range, with reheating as needed so the part does not finish too cold. Nitrogen-alloyed austenitics work-harden quickly, so reductions and finishing temperature are planned to leave a structure that will fully recrystallise during solution annealing.

Solution annealing

This grade cannot be hardened by heat treatment. It is supplied solution annealed. Published practice for 317LN places the treatment between 1080 and 1175 degrees C, followed by rapid water quenching to hold carbides and intermetallics in solution. Where final forming finishes below roughly 950 degrees C, a re-solution anneal is needed to restore corrosion performance. The exact cycle is set per part geometry and section thickness.

Machining and fabrication

Nitrogen content makes the grade work-harden fast, so machining needs rigid setups, positive rake, heavy feeds, sharp tooling and plenty of coolant. Dwelling or rubbing glazes the surface and should be avoided. Welding follows normal low-carbon austenitic practice, and the 0.030 percent carbon limit means post-weld annealing is not usually required to avoid sensitisation in thin sections.

Inspection and documentation

Ultrasonic examination is carried out to EN 10228-4, the part of the EN 10228 series that covers austenitic and austenitic-ferritic stainless steel forgings. ASTM A388 or SEP 1921 can be applied where the buyer specification calls for them. Certification is issued to EN 10204 3.1, or 3.2 with third party endorsement such as TUV, BV, LR, DNV or SGS.

EN 10228-3 covers ferritic or martensitic forgings and is not the correct reference for an austenitic grade, although it is often quoted in error.

6. Where this grade is used

Low carbon, raised molybdenum and nitrogen strengthening make 1.4434 a step up where 316L is marginal on chlorides, or where a higher design stress is wanted from an austenitic steel.

SectorTypical forged componentsReason for the grade
Chemical and petrochemicalRolled rings, shafts, nozzles, reactor internalsResistance to organic, sulphuric and phosphoric acids
Pressure equipmentTube sheets, flanges, forged tubes, shell courses, air receiversListed in EN 10028-7 and AD 2000 W 2 for pressure purposes
Heat exchangersTube sheets, channel covers, baffle ringsChloride pitting resistance at PREN about 32
Marine and chemical tankersFlanges, valve bodies, pump shaftsMolybdenum and nitrogen resistance to chloride cargo and seawater splash
Flue gas desulphurisationRings, discs, scrubber internalsAcidic chloride-bearing condensate service
ValvesStems, seat rings, bodies, blocks and plugs for ball, gate, globe and check valvesHigher proof strength than 317L at the same corrosion class
CryogenicFlanges, rings, structural forgingsImpact energy retained at minus 196 degrees C
Rotating equipmentShafts, spindles, gears, rolls, crankshaftsToughness and corrosion resistance in one material

7. Availability and sourcing

EN 10088-2 classes 1.4434 as an austenitic special grade. Availability guidance published by the British Stainless Steel Association rates it at level 4 for both flat and long products, meaning it is normally obtainable only from mills when enough quantity is ordered, not from a stockholder shelf.

That is the gap an open-die forge fills. Because we forge from ordered melt rather than standing stock, Jiangyin Jiangnan Metal Co., Ltd. can supply X2CrNiMoN18-12-4 in one-off and low-volume quantities and in section sizes no stockist carries. Send a drawing or dimension list with the governing standard, the required testing and the certification level, and we will quote.

8. Common questions

What is X2CrNiMoN18-12-4?
X2CrNiMoN18-12-4, material number 1.4434, is a low-carbon nitrogen-alloyed austenitic stainless steel defined in EN 10088-1 and EN 10088-2. It contains 16.5 to 19.5 percent chromium, 10.5 to 14.0 percent nickel, 3.0 to 4.0 percent molybdenum and 0.10 to 0.20 percent nitrogen, with carbon capped at 0.030 percent. EN 10088-2 classes it as an austenitic special grade.
Is X2CrNiMoN18-12-4 the same as 317LN?
They are recognised equivalents. 1.4434 cross-references to AISI 317LN, UNS S31753, JIS SUS 317LN, KS STS 317LN and GB 022Cr19Ni13Mo4N. The standards are not identical documents, so where a purchase order names ASTM A240 Type 317LN, the material has to be certified to that ASTM specification and not only to EN 10088.
How does 1.4434 compare with 316L?
1.4434 carries 3.0 to 4.0 percent molybdenum against roughly 2.0 to 3.0 percent in 316L (1.4404), plus a deliberate nitrogen addition of 0.10 to 0.20 percent that 316L does not have. The result is higher resistance to chloride pitting and crevice corrosion, PREN around 32, and a higher minimum 0.2 percent proof strength, which can allow a thinner section at the same design pressure. Both share the 0.030 percent carbon maximum that resists weld sensitisation.
What is the PREN of X2CrNiMoN18-12-4?
About 32. PREN is a calculated index from chromium, molybdenum and nitrogen content. It ranks alloys against each other but does not predict service life in a specific environment. Confirm suitability by corrosion testing or from published isocorrosion data for your chemistry and temperature.
Can this grade be hardened by heat treatment?
No. Like other austenitic stainless steels it is not hardenable by heat treatment, and strength is raised only by cold work. It is supplied solution annealed, with published practice for 317LN using a treatment between 1080 and 1175 degrees C followed by rapid water quenching.
Which ultrasonic testing standard applies?
EN 10228-4, which covers ultrasonic testing of austenitic and austenitic-ferritic stainless steel forgings. EN 10228-3 applies to ferritic or martensitic forgings and is the wrong reference for this grade. ASTM A388 or SEP 1921 can be substituted where specified.
What sizes and shapes can Jiangyin Jiangnan Metal supply?
All parts are custom. We produce seamless rolled rings, forged flanges, shafts, discs, bushings, sleeves, tube sheets, round bars, forged pipes and tubes, rolls and crankshafts in X2CrNiMoN18-12-4 to the customer drawing. Send dimensions, the governing standard, the required testing and the certification level to sales@steelforgepieces.com for a quotation.
What certification is provided?
EN 10204 3.1 as standard, or EN 10204 3.2 countersigned by a third party inspection body. Certificates record the melt route, chemical analysis, heat treatment condition, mechanical test results and NDT results against the ordered standard.

Related stainless steel forging grades

Request a quotation

Send your drawing or dimensions, the governing standard, the testing you need and the certification level. We reply with price, lead time and a proposed manufacturing and test plan.

CompanyJiangyin Jiangnan Metal Co., Ltd.
Open-Die Forging Factory
AddressNo.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Phone and WhatsApp+86 189-2135-9659

Data sources. Composition limits per EN 10088-2. Minimum mechanical properties per EN 10028-7. Grade cross-references per ISO 15510 and Stahlschluessel. Availability rating per the British Stainless Steel Association. Typical physical and mechanical values describe the grade and are not guaranteed. Published data does not replace the ordered specification or the mill certificate for the heat supplied.
Published by Jiangyin Jiangnan Metal Co., Ltd. Last reviewed . A plain text version of this page is available at X2CrNiMoN18-12-4.md.