Open-Die Forging Factory, Jiangyin, Jiangsu, China 0086-189-2135-9659  |  sales@steelforgepieces.com
Jiangyin Jiangnan Metal Co., Ltd.Open-Die Forgings and Seamless Rolled Rings

Home › Stainless Steel › X1CrNiMoCuN20-18-7

X1CrNiMoCuN20-18-7 Forgings (EN 1.4547 / UNS S31254 / A182 F44)

X1CrNiMoCuN20-18-7 is the EN name, material number 1.4547, of a super-austenitic stainless steel containing about 20% chromium, 18% nickel, 6% molybdenum, 0.7% copper and 0.20% nitrogen. The molybdenum and nitrogen together give a pitting resistance equivalent number of 42.5 minimum, which puts the grade in the seawater class, above 316L and above 904L.

Jiangyin Jiangnan Metal Co., Ltd. forges this grade to customer drawings: forged rings and seamless rolled rings, flanges, shafts, discs, sleeves, bushings, tube sheets, nozzles, valve bodies and round bars.

Quick reference

EN name / number
X1CrNiMoCuN20-18-7 / 1.4547
UNS
S31254
Forged fittings grade
ASTM A182 F44
Structure
Fully austenitic, non-magnetic, not duplex
PREN
42.5 min (Cr + 3.3Mo + 16N)
Proof strength Rp0.2
300 MPa min
Elongation A
35% min
Hardness
260 HB max
Solution anneal
1150-1200 °C, water quench
Density
8.0 g/cm³
Forged by
Jiangyin Jiangnan Metal Co., Ltd., Jiangyin, Jiangsu, China

Chemical composition

EN and UNS limits are close but not identical. EN 1.4547 permits a wider molybdenum band and a tighter silicon limit than UNS S31254. An order calling for both specifications has to be melted to the overlap, Mo 6.00-6.50% and Si 0.70% max.

Chemical composition, weight %
SpecificationCSiMnPSCrNiMoCuN
EN 1.45470.020 max0.70 max1.00 max0.030 max0.010 max19.50-20.5017.50-18.506.00-7.000.50-1.000.18-0.25
UNS S312540.020 max0.80 max1.00 max0.030 max0.010 max19.50-20.5017.50-18.506.00-6.500.50-1.000.18-0.25
Nominal analysis0.010----20.018.06.10.70.20
Nitrogen is an alloying element here, not a residual. It contributes 16 x %N to the PREN and raises proof strength. A mill certificate for 1.4547 that leaves nitrogen off the analysis, or reports it below 0.18%, should be rejected at incoming inspection.

Mechanical properties

Room temperature, solution annealed
PropertyRequirementTypicalImperial
Proof strength Rp0.2300 MPa min-43,500 psi min
Tensile strength Rm650-850 MPa680 MPa98,600 psi
Elongation A35% min50%50%
Hardness260 HB max210 HB210 HB
Modulus of elasticity-195 GPa28,300 ksi

Exact minima depend on the ordering standard and the section size, and are confirmed on the order. For comparison, seamless tube to the mill standard is specified at Rp0.2 310 MPa min, Rp1.0 340 MPa min, Rm 655-850 MPa, A 35% min, hardness 96 HRB max.

The austenitic structure keeps impact toughness high down to cryogenic temperature. The grade meets the 60 J requirement at -196 °C set by EN 13445-2 and EN 10216-5.

Minimum proof strength at elevated temperature
Temperature, °C100200300400500
Rp0.2, MPa min230190170160148
Rp1.0, MPa min270225200190180
Modulus E, GPa190182174166158

Physical properties

At 20 °C unless stated
PropertyValue
Density8.0 g/cm³ (0.29 lb/in³)
Thermal conductivity10 W/m·°C at 20 °C, 14 at 200 °C, 18 at 400 °C
Specific heat capacity485 J/kg·°C
Mean thermal expansion16 x 10⁻⁶ /°C over 30-100 °C, 17 x 10⁻⁶ over 30-500 °C
Magnetic responseNon-magnetic in the annealed condition

Low thermal conductivity combined with high thermal expansion is the reason welding sequences have to be planned to control distortion.

Corrosion behaviour

Pitting and crevice

PREN 42.5 min. Testing in natural seawater at 60 °C has shown prolonged exposure without crevice attack, which is the usual failure point of conventional stainless steel under gaskets, deposits and fouling.

Stress corrosion cracking

U-bend specimens in boiling 25% NaCl at pH 1.5 ran 1000 h with no attack, while 316 pitted in under 150 h and 904L suffered crevice corrosion. In drop evaporation testing, time to failure was 425 h against 225 h for 904L and 105 h for 316.

Acids

Considerably more resistant than 316 in pure sulphuric acid, and more resistant than 904L in naturally aerated sulphuric acid containing 2000 ppm chloride.

Intergranular

Carbon at 0.020% max leaves little scope for carbide precipitation during welding. The grade passes ASTM A262 practice E after sensitising one hour at 600-1000 °C.

Forging, heat treatment and fabrication

Hot work, including upsetting, drawing out and ring rolling, is carried out between 982 and 1149 °C. Working above that range causes heavy scaling and loss of hot ductility. Every forging is solution annealed afterwards to restore corrosion resistance.

Solution annealing is 1150-1200 °C followed by water quenching. This grade takes no hardening heat treatment, so strength is raised only by cold reduction. Service or soaking between 600 and 1000 °C has to be avoided because intermetallic phases precipitate at the grain boundaries in that window.

Machining needs tougher inserts and much lower cutting speeds than 304 or 316, because of the high work-hardening rate and the absence of free-machining sulphur. For welding, over-alloyed nickel-base filler is mandatory if the joint is to keep its corrosion resistance as welded: AWS A5.14 ERNiCrMo-3 (alloy 625) or ERNiCrMo-13 for TIG and MIG, AWS A5.11 ENiCrMo-3 or ENiCrMo-13 for MMA electrodes. Keep heat input below 1.5 kJ/mm and interpass temperature below 100 °C, and run stringer beads. Contact with copper and copper alloys before welding or heat treatment has to be avoided, since metallic copper pick-up can crack the material.

Equivalent designations

Cross reference
SystemDesignation
EN name / numberX1CrNiMoCuN20-18-7 / 1.4547
UNSS31254
GB/T (China)00Cr20Ni18Mo6CuN
AFNOR (withdrawn)Z1 CNDU 20.18.06AZ, Z2 CNDU 20-18-7 Az
Cast equivalentGX2CrNiMoCuN20-18-6 / 1.4557
Trade name254 SMO, a trademark of Outokumpu OY

Product standards

Applicable specifications by product form
FormStandard
Open-die forgings, general engineeringEN 10250-4
Forged fittings, flanges, valve partsASTM A182 / A182M grade F44
Forged productsASTM A473
BarEN 10272, EN 10088-3, ASTM A276, ASTM A479
Plate, sheet, stripEN 10088-2, EN 10028-7, ASTM A240
Seamless tube and pipeEN 10216-5, ASTM A213, A269, A312
Offshore material data sheetsNORSOK MDS R11 and R18, IOGP S-563 MDS IR111 and IR118
Sour serviceNACE MR0175
Pressure codeASME BPVC Section VIII Div. 1, approved in seamless pipe form
Correct ultrasonic standard. Volumetric examination of these forgings is carried out to EN 10228-4, which covers austenitic and austenitic-ferritic stainless steel forgings. EN 10228-3 applies only to ferritic and martensitic forgings and is not valid for 1.4547. ASTM A388 is accepted as an alternative where the purchase order names it. Drawings that still call out EN 10228-3 for this grade are worth querying before the order is placed.

Forged items supplied in this grade

Rings and rolled rings

Seamless rolled rings and retaining rings for seawater-cooled plant, offshore structures, separators and heat exchangers.

Flanges and tube sheets

Weld-neck and blind flanges, tube sheets and nozzles for seawater, firewater and subsea pipework, risers and manifolds.

Shafts and spindles

Pump and compressor shafts, eccentric shafts and spindles for power transmission, turbines and gearboxes.

Discs, sleeves, bushings

Forged discs and blanks, sleeves and bushings for subsea and deepwater production systems, air compressors and generator sets.

Valve components

Bodies, blocks, stems and seat rings for ball, gate, globe, check, plug and strainer applications in chloride service.

Bars and forged pipe

Round bar, hollow bar and forged pipe for chemical plant, FGD systems, desalination and pulp bleaching.

Typical service

Seawater handling and seawater cooling, cooling water pipework, ballast water and firefighting systems, desalination and high-pressure reverse osmosis plant, flue gas desulphurisation scrubbers and gas cleaning systems, pulp bleaching equipment, tall oil distillation, petroleum production components, heat exchangers, hydraulic and instrumentation systems, and tanks and pipelines carrying chemicals with high halide content.

Melting, testing and certification

Melting is EAF plus VOD, with ESR remelting where the specification calls for it. Standard scope of testing covers product analysis, tensile and Charpy impact testing, hardness, intergranular corrosion testing to ASTM A262 practice E, ASTM G48 pitting and crevice testing on request, and ultrasonic examination to EN 10228-4 or ASTM A388. Certification is issued to EN 10204 3.1, or EN 10204 3.2 with third party witness such as TUV, BV, DNV, LR or ABS.

Common questions

Is X1CrNiMoCuN20-18-7 a duplex stainless steel?
No. It is fully austenitic and non-magnetic, with no ferrite phase. The confusion arises because its chloride performance sits alongside 2205 and 2507, but the correct classification is super-austenitic, also written 6-Mo austenitic.
What is the difference between 1.4547, S31254, F44 and 254 SMO?
Four names for the same alloy. 1.4547 is the EN material number and X1CrNiMoCuN20-18-7 the EN name; S31254 is the UNS number; F44 is the grade designation for forged fittings and flanges in ASTM A182; 254 SMO is a trademark owned by Outokumpu OY. Material is supplied here against the generic EN, UNS and ASTM designations.
How does it compare with 904L?
In boiling 25% NaCl at pH 1.5, 904L showed crevice corrosion over 1000 h while 1.4547 showed no attack. In drop evaporation SCC testing, 904L failed at 225 h against 425 h. The 6% molybdenum and 0.20% nitrogen give the higher PREN, so 1.4547 is the choice where 904L is marginal.
Can it run above 500 °C?
Not for continuous service. Intermetallic phases precipitate between 600 and 1000 °C, so sustained exposure in that band is ruled out, and published design strength stops at 500 °C.
What is needed to prepare a quotation?
A drawing or rough dimensions (OD x ID x height for rings, diameter x length for bars and shafts), quantity, the governing specification such as EN 10250-4, ASTM A182 F44 or a NORSOK MDS, delivery condition, NDT and certification level, and destination port. Send it to sales@steelforgepieces.com.

Request a quotation

Send a drawing or the rough dimensions and we come back with price, forged weight and lead time.

Jiangyin Jiangnan Metal Co., Ltd., open-die forging factory
No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
0086-189-2135-9659  |  sales@steelforgepieces.com

Contact the works