GRADE X12CrS13 / EN 1.4005 / AISI 416 / UNS S41600 STANDARD EN 10088-3 REV 2026-10-09 MARKDOWN
Jiangnan Metal Open-Die Forging Works · Jiangyin, China Get a quote

Free-machining martensitic stainless steel

X12CrS13 Forgings EN 1.4005 · AISI 416 · UNS S41600 · bars, rings, discs and valve parts

X12CrS13, material number 1.4005, is a 12 to 14 % chromium martensitic stainless steel with 0.15 to 0.35 % sulphur added for machinability. It is the EN grade matching AISI 416 / UNS S41600. The sulphur buys short chips and high cutting speeds and costs corrosion resistance, weldability and cold formability against 1.4006 (AISI 410). Jiangyin Jiangnan Metal melts and forges this grade on one site, so the certificate traces back to a melt number rather than to a purchased billet.

Grade data sheetEN 10088-3
Steel name
X12CrS13
Material number
1.4005
US grade
AISI 416 / UNS S41600
Structure
Martensitic, hardenable, ferromagnetic
Rm, +QT650
650 to 850 MPa
Rp0.2, +QT650
450 MPa minimum
Hardness, +A
220 HB maximum
Machinability
About 85 %, highest of the stainless steels
Forging range
1180 to 1000 °C, slow cool
Certification
EN 10204 3.1, 3.2 witnessed on request
01

Chemical composition

Composition limits to EN 10088-3, balance iron. Elements outside the table are not added deliberately unless agreed with the purchaser.

Table 1 · Chemical composition, % by mass
CSiMnPSCrMo
0.06 - 0.15 max 1.00 max 1.50 max 0.040 0.15 - 0.35 12.0 - 14.0 max 0.60

The Swiss Steel / Deutsche Edelstahlwerke datasheet for 1.4005 quotes a narrower carbon band of 0.08 to 0.15 % with the same chromium, sulphur and molybdenum limits. Tighter internal ranges can be held on request where a customer specification demands it.

02

Equivalent grades

Table 2 · International cross-reference
Standard / countryDesignation
EN 10088-3, EuropeX12CrS13, 1.4005
DIN 17440, Germany, withdrawn1.4005
ASTM / AISI / UNS, USA416, UNS S41600, bars to ASTM A582
BS, United Kingdom, old416S21, En 56AM
JIS G 4303, JapanSUS 416
AFNOR, FranceZ11CF13
SIS, Sweden2380
GB/T 20878, ChinaY12Cr13, formerly Y1Cr13

These are nearest-match designations, not identical specifications. AISI 416 allows manganese to 1.25 % and phosphorus to 0.060 %, while 1.4005 allows manganese to 1.50 % and phosphorus to 0.040 %. Name one controlling specification on the purchase order.

03

Mechanical properties

Table 3 · EN 10088-3, hot-formed bars and sections, minimum values unless stated
ConditionThickness dRp0.2 MPaRm MPaA %Hardness HB
+A, annealed--max 730-max 220
+QT650, quenched and temperedbelow 160 mm450650 - 85012-

Typical delivered values in +QT650 run near 480 MPa proof strength, 710 MPa tensile strength and 14 % elongation. That condition comes from hardening at 950 to 1000 °C in air or oil and tempering between 680 and 780 °C. In sections up to 35 mm, straightening work raises hardness by roughly 60 HB and tensile strength by roughly 150 MPa. From 160 mm upward the standard leaves properties to agreement between purchaser and manufacturer, which is a routine item in order review for heavy open-die work.

Tempering response

Table 4 · Typical tempering response of grade 416 bar, ASTM A582 reference data, guidance only
Tempering temperature °CRm MPaRp0.2 MPaElongation %Hardness HB
Annealed51727530262
2041340105011388
3161350106012388
538100079513321
59384070519248
65079667017.5253

Impact resistance drops between roughly 400 and 580 °C, so tempering in that window is avoided. The 1.4005 mill datasheet separately warns against processing or service between 425 and 525 °C because of 475 °C embrittlement.

04

Physical properties

Table 5 · Physical properties of 1.4005 / 416, room temperature unless stated
PropertyValue
Density7.70 kg/dm3; 7.78 kg/dm3 reported for 416 elsewhere
Modulus of elasticity200 kN/mm2, about 190 to 200 GPa
Thermal conductivity at 20 °C30 W/(m·K); 24.9 W/(m·K) at 100 °C reported for 416
Specific heat capacity at 20 °C460 J/(kg·K)
Electrical resistivity at 20 °C0.60 ohm·mm2/m
Coefficient of thermal expansion10.5 x 10-6 /K, 20 to 100 °C; 11.5 x 10-6 /K, 20 to 300 °C; 12.0 x 10-6 /K, 20 to 400 °C
Magnetic responseFerromagnetic in all delivery conditions
Melting rangeAbout 1482 to 1532 °C
05

Forging, heat treatment, machining, welding

Forging

Practice for 1.4005 is gradual heating to about 800 °C, then faster heating to 1150 to 1180 °C. Forging runs between 1180 and 1000 °C and the piece is cooled slowly in a furnace, in dry ash or an equivalent medium. In this works that means controlled-rate furnace heating, a pyrometer record of finishing temperature on every heat, covered slow cooling, then annealing or quench and temper to the ordered condition.

Heat treatment

  • Annealing, +A. 745 to 825 °C with slow furnace cool, giving tensile strength up to 730 MPa and hardness up to 220 HB. Sub-critical annealing of 416 is usually 650 to 760 °C, air cooled.
  • Hardening. Austenitise at 950 to 1000 °C, quench in air or oil.
  • Tempering to +QT650. 680 to 780 °C. Keep out of the 400 to 580 °C range.

Machining

Machinability is the whole point of this grade. Grade 416 is rated at about 85 %, the highest of the stainless steels, and the manganese sulphide inclusions break chips cleanly for automatic screw machining. With coated carbide in the annealed condition at 600 to 685 N/mm2 tensile strength, turning at 6 mm depth of cut and 0.5 mm per revolution runs near 160 m/min, and at 1 mm depth of cut and 0.2 mm per revolution near 300 m/min. In the quenched and tempered condition at 750 to 950 N/mm2 the equivalent figures are about 200 and 350 m/min. Final parameters depend on the delivery condition.

Welding

The high sulphur content makes this a poor welding grade, friction welding excepted. Where a weld is unavoidable, 1.4833 filler is suggested, tempering at 650 °C afterwards restores some ductility in the weld and heat-affected zone, and the shielding gas must carry no nitrogen or hydrogen. General 416 practice adds preheat at 200 to 300 °C and a post-weld anneal or stress relief at 650 to 675 °C.

Corrosion resistance, check this before specifying

The chromium content reads like a stainless steel, but the sulphur pulls corrosion performance down. The 1.4005 datasheet calls it probably the least corrosion-resistant of the stainless grades, and 416 is not suitable for chloride or marine service. It handles ordinary atmospheric exposure, fresh water and dry air, and performs best hardened and polished. If corrosion matters more than cycle time, 1.4104 (X14CrMoS17) is the free-machining grade with better corrosion resistance, 1.4006 / 410 trades machinability for corrosion resistance and formability, and 303 is the non-hardenable austenitic option.

06

What we forge in X12CrS13

  • Bars. Forged round bars and rods, square, rectangular and flat bars, hexagonal bars.
  • Hollow sections. Forged hollow bars, sleeves, bushes and bushings, pipes and tubes, barrels, casings, shells, cylinders, hubs and housings, bored from solid forged blanks.
  • Rings. Forged rings and seamless rolled rings in rectangular, stepped and contoured section.
  • Solids. Forged blocks, discs and plates, supplied proof-machined where volumetric inspection is required.
  • Valve and rotating parts. Valve bodies and bonnets, valve stems, valve seats and seat rings, pump shafts, motor shafts, gears, bolts, nuts and studs.

Standards worked to for this grade include EN 10088-3 for bars, rods and sections, EN 10250-4 for open-die steel forgings in stainless steels, ASTM A473 for stainless steel forgings and ASTM A582 for free-machining stainless bars.

Table 6 · Plant capability relevant to this grade
ItemDetail
MeltingElectric arc furnace with ladle refining and vacuum oxygen decarburisation, 60 t maximum heat, melted on site
Forging6,300 t, 4,000 t and 2,000 t hydraulic open-die presses; hammers from 750 kg to 5 t
Ring rollingRadial-axial mills at 6 m, 3 m and 1 m, maximum outside diameter 6,000 mm
Maximum single piece30 tonnes
Heat treatment14 furnaces, car-bottom and 15 m well type for vertical quenching of long shafts
Delivery conditionAs-forged, rough machined, +A annealed or +QT650 quenched and tempered
TestingOn-site spectrometry, tensile, Charpy impact, hardness, ultrasonic to ASTM A388 and EN 10228-3, magnetic particle to ASTM E709, metallography
CertificationEN 10204 3.1 as standard; 3.2 witnessed by BV, DNV, LR, SGS, TUV or the customer's inspector on request
Class approvalsCCS, BV, DNV, LR, NK
Minimum order10 kg, no minimum piece count
Lead time20 to 60 days; X12CrS13 needs no remelting step and normally sits at the shorter end

Quote an X12CrS13 forging

Send the drawing, or the dimensions, weight, delivery condition and quantity. Quotations normally go back within two working days. Minimum order 10 kg, single pieces accepted.

sales@steelforgepieces.com +86 189 2135 9659 Contact page
07

Questions buyers ask

What is X12CrS13 used for?

Parts that take heavy machining and still need 13 % chromium corrosion resistance: valves and valve trim, valve stems and seats, pump and motor shafts, electric motor parts, gears, bolts, nuts and studs, automatic screw machine parts and washing machine components. Main industries are automotive, petrochemical, electronic equipment and general mechanical engineering.

Is X12CrS13 the same as 1.4005 and AISI 416?

X12CrS13 is the EN steel name and 1.4005 is the EN material number for the same steel. The closest American grade is AISI 416 / UNS S41600. Other equivalents are BS 416S21, JIS SUS 416, AFNOR Z11CF13, SIS 2380 and Chinese Y12Cr13.

Is X12CrS13 magnetic?

Yes. It is a martensitic chromium steel and stays ferromagnetic in every normal delivery condition.

Can X12CrS13 be hardened?

Yes, it hardens by heat treatment: 950 to 1000 °C in air or oil, then tempered to the required condition. EN 10088-3 normally lists it in +QT650 at 650 to 850 MPa tensile strength. Grade 416 reaches around 40 HRC, and nitriding gives a harder surface.

What service temperature is realistic?

High temperature service is not recommended because of the sulphur content, and sub-zero service is not recommended because ductility falls. Scaling resistance of 416 extends to about 760 °C intermittent and 675 °C continuous, but the steel should not run above its tempering temperature if the mechanical properties have to hold, and 425 to 525 °C should be avoided.

What sizes can you forge in this grade?

Rings roll to 6,000 mm outside diameter and the heaviest single forging is 30 tonnes, but the practical limit for any given part depends on geometry and section. Send the drawing or the finished dimensions and weight and we will confirm feasibility, forging route, heat treatment and lead time.

Do you supply finish-machined parts or rough forgings?

Both. Forgings can be supplied as-forged with machining allowance, rough-machined to a proof-machined condition suitable for ultrasonic testing, or finish-machined to drawing. Heat treatment, machining and testing are all carried out in-house before shipment.

08

Data sources

  1. EN 10088-3 composition and mechanical property tables for martensitic stainless long products, published by the British Stainless Steel Association.
  2. Swiss Steel Group / Deutsche Edelstahlwerke material datasheet 1.4005 X12CrS13, covering composition, physical properties, forging, heat treatment, machining, welding and corrosion behaviour.
  3. AZoM, Stainless Steel Grade 416 (UNS S41600): ASTM A582 bar properties, heat treatment, corrosion and applications.
  4. SteelNumber, X12CrS13 / 1.4005, EN 10088-3:2005.
  5. TJC Steel grade comparison, Y12Cr13 / 416 / SUS 416 / 1.4005, GB/T 20878 cross-reference.

Figures above are published reference data for the grade and are given for guidance. Certified values for a specific forging appear on the EN 10204 inspection certificate issued with the order.