UNS S44002 (AISI 440A) Forgings: Bars, Rings, Discs and Valve Components
High-carbon martensitic stainless steel, forged to drawing by Jiangyin Jiangnan Metal Co., Ltd., an open-die forging factory in Jiangyin, Jiangsu, China.
UNS S44002 is the UNS number for AISI type 440A, a high-carbon (0.60 to 0.75 percent C), high-chromium (16 to 18 percent Cr) martensitic stainless steel with up to 0.75 percent molybdenum. It carries moderate corrosion resistance with high hardness and wear resistance, and reaches about Rockwell C 56 to 57 after hardening and low-temperature tempering. We supply it as open-die forged bars, hollow bars, seamless rolled rings, discs, blocks, shafts and finished valve parts, quoted to drawing.
- UNS Number
- S44002
- Common Name
- AISI / SAE 440A
- Type
- Martensitic stainless
- Carbon
- 0.60 to 0.75 %
- Chromium
- 16.00 to 18.00 %
- Max Hardness
- HRC 56 to 57
- Density
- 7.68 g/cm3
- Forging Range
- 1038 to 1204 C
1. Grade Overview
Type 440A was developed to give stainless behaviour together with tool-steel hardness. It holds the lowest carbon content of the 440 family, which is why it is usually described as tougher and somewhat more corrosion resistant than 440B and 440C while still hardening to a high working hardness. In machining and hot working it behaves much like a high-speed tool steel.
Corrosion resistance is broadly similar to type 410. The grade has resisted mild atmospheres, fresh water, steam, ammonia, many petroleum products and organic materials, and some mild acids. Best corrosion performance comes from the hardened and tempered condition with tempering held below roughly 427 C (800 F). Tempering above that point lowers corrosion resistance, which is also why the grade is not normally chosen for elevated-temperature service.
2. Chemical Composition
| Element | Symbol | Content (%) |
|---|---|---|
| Carbon | C | 0.60 to 0.75 |
| Chromium | Cr | 16.00 to 18.00 |
| Molybdenum | Mo | 0.75 max |
| Manganese | Mn | 1.00 max |
| Silicon | Si | 1.00 max |
| Phosphorus | P | 0.040 max |
| Sulfur | S | 0.030 max |
| Iron | Fe | Balance |
Composition per the CarTech 440A (UNS S44002) alloy datasheet. Limits vary slightly between ASTM, AMS and national standards, so state the governing specification on your enquiry.
3. Mechanical Properties
| Property | Metric | Imperial |
|---|---|---|
| Tensile strength | 725 to 1790 MPa | 105,000 to 260,000 psi |
| Yield strength (0.2 % offset) | 415 to 1650 MPa | 60,200 to 239,000 psi |
| Modulus of elasticity | 204 to 215 GPa | 29,600 to 31,200 ksi |
| Elongation at break (in 50 mm) | 5 to 20 % | 5 to 20 % |
| Hardness, annealed | about 223 HB (about 95 HRB) | about 223 HB (about 95 HRB) |
| Hardness, hardened and tempered | 56 to 57 HRC | 56 to 57 HRC |
The spread reflects delivery condition, not scatter. The low end is the fully annealed state, the high end the hardened and low-temperature tempered state. Specify the required condition and hardness band on the purchase order.
4. Physical Properties
| Property | Value |
|---|---|
| Specific gravity | 7.68 |
| Density | 7.68 g/cm3 (0.2770 lb/in3) |
| Mean specific heat, 0 to 100 C | about 460 J/kg.K (0.110 Btu/lb.F) |
| Mean thermal expansion, 0 to 100 C | about 10.1 x 10-6 /C (5.60 x 10-6 in/in/F) |
| Electrical resistivity at 21 C | about 0.60 micro-ohm.m (361 ohm.cmil/ft) |
| Magnetic response | Ferromagnetic, makes fair permanent magnets |
5. Forging and Heat Treatment Practice
Forging and hot working
Treat UNS S44002 as a high-speed tool steel. Preheat to 760 to 816 C (1400 to 1500 F), then heat slowly and uniformly to 1038 to 1204 C (1900 to 2200 F). Do not forge below 927 C (1700 F), and reheat as often as the shape demands. Cool in a furnace where possible, or in warm dry lime or ashes, and bring to room temperature before annealing. Anneal after forging.
Annealing
For maximum softness, heat uniformly to 843 to 871 C (1550 to 1600 F), soak and cool very slowly in the furnace, giving about 223 HB. For process or intermediate annealing, heat uniformly to 732 to 760 C (1350 to 1400 F) and furnace cool or air cool, giving about 230 HB.
Hardening and tempering
Preheat to 760 to 816 C (1400 to 1500 F), austenitise at 1010 to 1066 C (1850 to 1950 F), soak, then quench in warm oil or cool in air. Do not overheat, since an overheated part will not reach full hardness. Temper at least one hour at 148 to 176 C (300 to 350 F) to relieve peak stresses while keeping maximum hardness, giving roughly HRC 56 to 57. Where corrosion resistance matters, keep tempering below about 427 C (800 F).
Machining, grinding and welding
Machine in the dead-soft annealed condition. Carbide or ceramic tooling suits the grade, and chip breakers matter because the chips run tough and stringy. On blade and cutlery work, avoid overheating during grinding and polishing, which can lower corrosion resistance. Welding is seldom carried out because of the high hardenability. Where it cannot be avoided, preheat and hold at about 260 C (500 F), weld with high heat input, then anneal immediately for 6 to 8 hours at 732 to 760 C (1350 to 1400 F) with a slow furnace cool, never allowing the part to fall below 260 C between welding and annealing. Matching-composition consumables or AWS E/ER309 are the usual choices.
6. Corrosion Resistance Ratings
| Medium | Rating | Medium | Rating |
|---|---|---|---|
| Humidity | Good | Sulfuric acid | Restricted |
| Nitric acid | Moderate | Acetic acid | Restricted |
| Sodium hydroxide | Moderate | Salt spray (NaCl) | Restricted |
| Phosphoric acid | Restricted |
Temperature, concentration, pH, aeration, velocity, crevices, surface finish, applied stress and contact with dissimilar metals all change real service behaviour.
7. Equivalent Grades and Specifications
| Standard or Region | Designation |
|---|---|
| UNS (USA) | S44002 |
| AISI / SAE (USA) | Type 440A |
| EN / DIN (Europe) | 1.4109 / X70CrMo15 |
| JIS (Japan) | SUS 440A |
| GB (China) | 7Cr17 (near equivalent, 7Cr17MoV also cited) |
Product specifications commonly applied to this grade include ASTM A276 for stainless bars and shapes, ASTM A314 for billets and bars for forging, ASTM A473 for stainless forgings, ASTM A580 for stainless wire, ASTM F899 for stainless used in surgical instruments, plus AMS 5631 and QQ-S-763.
Equivalents are nearest-match references, not drop-in substitutions. Chemistry limits, test requirements and delivery conditions differ between standards, so confirm the governing specification before ordering.
8. UNS S44002 Forged Products We Manufacture
Jiangyin Jiangnan Metal Co., Ltd. produces UNS S44002 by open-die forging and seamless ring rolling, supplied as forged, rough machined, annealed, or hardened and tempered to a specified hardness band.
- Bars: forged round bars and rods, square, rectangular, flat and hexagonal bars.
- Hollow sections: forged hollow bars, sleeves, bushes and bushings, pipes and tubes, barrels, casings, shells, cylinders, hubs and housings.
- Rings: forged rings and seamless rolled rings, including valve seat rings and bearing races.
- Solids: forged blocks, discs, disks and plates, gauge blocks, mould and die blanks.
- Shafts and pins: forged shafts, pivot pins and bearing components.
- Valve and pump parts: valve seats, valve stems, valve bodies, bonnets, nozzles and pump parts.
- Precision and medical: cutlery and knife blanks, surgical and dental instrument blanks, measuring instrument components.
9. Typical Applications
Hardness and wear resistance at moderate corrosion exposure make UNS S44002 a common choice for pivot pins, dental and surgical instruments, cutlery and knife blades, valve parts and valve seats, ball bearings and races, gauge blocks, moulds and dies, nozzles, pump components and measuring instruments. Parts run fully hardened or selectively hardened. Pivot pins hardened only at the points are a long-standing example, relying on the usable corrosion resistance of the annealed body.
10. How to Order and How Pricing Works
Every UNS S44002 forging is made to order, so there is no list price. Cost depends on finished weight and envelope dimensions, delivery condition, machining allowance, testing and certification requirements, and order quantity. To receive a written quotation and lead time, send a drawing or a dimensional sketch, the governing specification, the required delivery condition and hardness band, any test or certificate requirements such as chemical analysis, mechanical testing or ultrasonic inspection, and the quantity required.
11. Frequently Asked Questions
What is UNS S44002 stainless steel?
UNS S44002 is the UNS number for AISI type 440A, a high-carbon high-chromium martensitic stainless steel with 0.60 to 0.75 percent carbon, 16 to 18 percent chromium and up to 0.75 percent molybdenum. It gives good strength, moderate corrosion resistance and high hardness and wear resistance.
How hard can UNS S44002 be heat treated?
Austenitised at 1010 to 1066 C (1850 to 1950 F), quenched, then tempered at least one hour at 148 to 176 C (300 to 350 F), it reaches about HRC 56 to 57. Annealed, it runs about 223 HB, roughly 95 HRB.
Is 440A better than 440C?
Neither one is better across the board. 440A holds the lowest carbon of the family, so it is reported to offer higher toughness and generally better corrosion resistance, while 440C reaches higher attainable hardness and wear resistance. Pick 440A where toughness and corrosion matter more than peak hardness, and 440C where maximum hardness and abrasion resistance dominate. Service environment and required wear life usually decide it.
What is the forging temperature for UNS S44002?
Preheat to 760 to 816 C, heat to 1038 to 1204 C, and stop forging before the piece falls below 927 C. Cool slowly, then anneal after forging.
Can UNS S44002 be welded?
It is seldom welded. Where necessary, preheat and hold at about 260 C, weld, then anneal immediately for 6 to 8 hours at 732 to 760 C with a slow furnace cool, without letting the part cool below 260 C in between.
What sizes and quantities can you forge?
Jiangyin Jiangnan Metal Co., Ltd. is an open-die forging factory producing bars, rings, discs, sleeves and shafts to customer drawings. Send your drawing, specification, delivery condition and quantity to sales@steelforgepieces.com and our engineers will confirm workable dimensions, tolerances and lead time.
How is UNS S44002 priced and quoted?
All parts are made to order, so price depends on weight, dimensions, delivery condition, machining allowance, test and certification requirements and quantity. Send a drawing or specification for a written quotation and lead time.
Request a Quotation for UNS S44002 Forgings
Send a drawing or specification and we will come back with the forging route, heat-treatment condition, certification plan and lead time.
Jiangyin Jiangnan Metal Co., Ltd., Open-Die Forging Factory
No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Tel: +86 189-2135-9659
Email: sales@steelforgepieces.com
Related Stainless Steel Forging Grades
Sources. Carpenter Technology, CarTech 440A Stainless alloy datasheet (UNS S44002), for composition, heat treatment, physical properties, corrosion ratings and applicable specifications. AZoM, Stainless Steel Grade 440A (UNS S44002), for mechanical property ranges. Equivalent-grade cross references compiled from published stainless grade comparison tables.
Published by Jiangyin Jiangnan Metal Co., Ltd., open-die forging factory, Jiangyin, Jiangsu, China. Last reviewed . Values are typical and are not guaranteed minima or maxima. Verify against the governing specification for your application.