GRADE SHEET UNS S32654  /  654 SMO  /  W.NR 1.4652 JIANGYIN JIANGNAN METAL CO., LTD.  EST. 1997 T +86 189 2135 9659   E sales@steelforgepieces.com
Jiangnan Metal Open-Die Forging & Ring Rolling Request Quote

Super Austenitic Stainless Steel

UNS S32654 Forgings 654 SMO · W.Nr 1.4652 · X1CrNiMoCuN24-22-8

Rolled rings, flanges, bars, discs, sleeves, shafts and tube sheets in the highest-alloyed super austenitic grade in common use. We melt the steel, forge it, solution anneal it and machine it on one site in Jiangyin, so the certificate traces back to a heat number rather than to a purchased billet.

UNS S32654, sold as 654 SMO and designated EN 1.4652, is a conventionally melted super austenitic stainless steel with roughly 24 to 25 percent chromium, 21 to 23 percent nickel, 7 to 8 percent molybdenum and 0.45 to 0.55 percent nitrogen. It is the most highly alloyed member of the SMO super austenitic family, and its resistance to pitting, crevice corrosion and chloride stress corrosion cracking comes close to that of nickel-based alloys. Buyers reach for it when a 6 percent molybdenum grade such as S31254 or 904L has already failed, or is predicted to fail, in hot seawater, concentrated brine or chlorinated acid service. Jiangyin Jiangnan Metal Co., Ltd. forges the grade to drawing at its works in Jiangyin, Jiangsu, China.

01

Grade identity

One alloy, several names. Enquiries arrive under all of them and they refer to the same chemistry.

Designations and cross-reference
SystemDesignationNote
UNSS32654Primary designation used in ASTM and ASME work
EN / Werkstoff1.4652European number, used in EN 10216-5 and EN 10217-7
EN nameX1CrNiMoCuN24-22-8Reads the chemistry directly
Trade name654 SMOOriginating producer designation, Outokumpu
Shorthand7Mo, Alloy 654Common in trading and older enquiry documents
JIS, GOST, GBNo direct listingGrade sits above the range of those standards; supplied against UNS or EN chemistry

654 SMO is a trademark of its owner and appears here only to identify the grade. Material is supplied to the UNS S32654 and EN 1.4652 chemistry, not under any third-party brand.

02

Chemical composition

The manganese figure is the one people query. It is high on purpose. Nitrogen at 0.45 to 0.55 percent will not stay in solution without it, and the nitrogen is where most of the strength and a large share of the pitting resistance comes from.

Composition, weight percent, balance iron
ElementRangeWhy it is there
Carbon0.020 maxHeld low against carbide precipitation at grain boundaries
Chromium24.0 – 25.0Passive film, first term in the PREN calculation
Nickel21.0 – 23.0Keeps the structure austenitic at this alloy level, resists chloride cracking
Molybdenum7.0 – 8.0Largest single contributor to pitting and crevice resistance
Nitrogen0.45 – 0.55Strength and pitting resistance, roughly twice the level in S31254
Manganese2.0 – 4.0Raises nitrogen solubility so the nitrogen stays in the melt
Copper0.30 – 0.60Helps in reducing conditions, sulphuric acid in particular
Silicon0.50 maxDeoxidation
Phosphorus0.030 maxResidual limit
Sulphur0.005 maxTight, for hot workability and clean inclusion rating

Copper is quoted as 0.30 to 0.60 in most forging and plate specifications. At least one published datasheet lists copper as 0.30 maximum. Confirm which window your specification applies before order and the heat will be aimed at it.

03

Mechanical and physical properties

Figures below are minima in the solution annealed condition. The yield strength is the commercially interesting number: close to double that of 316L, which is what lets a designer take wall thickness out of a high pressure brine component while gaining corrosion margin at the same time.

Tensile, min
750
MPa · 109 ksi
Yield 0.2 %, min
430
MPa · 62 ksi
Elongation, min
40
percent
Density
8.0
g/cm³
Room temperature properties, solution annealed
PropertyMetricImperial
Tensile strength, min750 MPa109 ksi
Yield strength, 0.2 % offset, min430 MPa62 ksi
Elongation, min40 %40 %
Hardness, annealedapprox. 220 HB max—
Density8.0 g/cm³0.289 lb/in³
StructureFully austenitic, non-magnetic as annealed, not hardenable by heat treatment

ASTM A312 lists the same 750 MPa and 430 MPa minima with 35 percent elongation rather than 40. Where a specification is named on the purchase order, that specification governs and the test certificate is issued against it.

Corrosion behaviour and PREN

PREN is calculated as %Cr + 3.3 × %Mo + 16 × %N. Figures published for S32654 do not agree, because they are calculated from different points in the composition range. Langley Alloys publishes 54. Datasheets working from the top of the range publish 63 to 64. Rather than quote the largest number, the honest statement is that S32654 lands between the mid-fifties and the low sixties depending on the heat, and that in every published comparison it sits well clear of the 6 percent molybdenum grades.

Published PREN comparison
GradeUNSMolybdenumPREN
316LS31603approx. 2 %25
254 SMO / Alloy 254S31254approx. 6 %43
654 SMOS326547 – 8 %54 to above 60, source dependent
04

What we forge in S32654

Every item is forged from one piece of steel. No welding, no casting, no billet of unknown origin.

Rolled ringsRing-rolled from a punched preform on the radial-axial mill. Rectangular or contoured section.
Forged ringsUpset and punched, for sections outside the ring mill envelope and where heavy reduction is wanted.
FlangesWeld neck, blind, slip-on, orifice, long weld neck and custom bore, to ASME B16.5 and B16.47 dimensions.
Round bars and blocksForged or rolled, black, peeled or turned. Feedstock for machined valve bodies.
Discs and tube sheetsSolid and bored discs, heat exchanger tube sheets and covers, proof-machined for volumetric inspection.
Sleeves and bushingsHollow forgings, trepanned or bored from solid on the deep-hole drilling machine.
Shafts and spindlesStepped shafts, pump shafts, eccentric shafts, pinions and rotors.
Valve and wellhead partsBodies, bonnets, stems, seat rings, blocks, spools and nozzles for ball, gate, globe, check and plug valves.

Size envelope

The limits below are the plant maximums across all grades. S32654 is a hard alloy to work, so the usable envelope in this grade is narrower, and each enquiry is reviewed against the drawing before a size is confirmed.

Plant working envelope
ItemLimitSet by
Rolled ring outside diameterup to 6,000 mm6 m radial-axial ring mill
Minimum ring sizefrom OD 50 mmUpset and punch route below ring mill range
Single piece weightup to 30,000 kg60 t heat, 6,300 t press
Machined diameterup to 5,000 mm5,000 mm vertical turning lathe
Shaft turned lengthup to 14,000 mmC61160 horizontal lathe, 15 m well furnace for vertical quench
Bored cylinders1,600 mm dia × 10,000 mmCNC deep-hole drilling machine
Minimum order10 kgNo minimum piece count
05

Melting, forging, heat treatment

Melting

Most forging suppliers in China buy billet. This works starts at the furnace. S32654 runs through the electric arc furnace, is refined in the ladle furnace, then decarburised under vacuum, which is the step that matters here: vacuum oxygen decarburisation is how carbon is pulled to 0.020 percent maximum while nitrogen is held at 0.45 to 0.55 percent. Where the order calls for it, the heat is electroslag remelted under protective atmosphere for inclusion cleanliness. Maximum heat size is 60 tonnes.

Forging

S32654 keeps its strength at temperature and has a short hot working window, so passes are planned to avoid finishing cold. Sigma and other intermetallic phases form in the region of 700 to 900 degrees Celsius, and time spent there during forging and cooling is kept down. Presses available are 6,300 t, 4,000 t and 2,000 t, with ring mills at 6 m, 3 m and 1 m.

Heat treatment

Solution anneal near 1150 to 1200 degrees Celsius, then rapid water quench. This returns intermetallics to solution and restores the corrosion resistance the alloy is bought for. The grade takes no precipitation hardening treatment. Fourteen furnaces are on site, including car-bottom furnaces to 8,000 × 2,000 × 2,000 mm and 15 m deep well furnaces for vertical quenching of long parts.

Note for fabricators

Where our forgings are welded into an assembly, a nickel-based filler of the ERNiCrMo type is normally used so that the weld metal does not become the weakest point in the corrosion chain.

06

Where it gets used

This is an expensive alloy and it is only specified where the environment pays for it. The established markets are these.

Service environments
SectorApplicationReason for the grade
DesalinationBrine heater internals, high pressure brine piping, MSF and MED plant, reverse osmosis high pressure sectionsBrine concentration and temperature beyond what 254 SMO and 904L will take
Offshore oil and gasSeawater and firewater systems, produced water handling, risers, manifolds, subsea connectorsChloride plus temperature plus pressure; the strength reduces dependence on cathodic protection
Chlor-alkali and chemicalChlorine and chlorine dioxide duty, sulphuric and mixed acid equipment carrying chlorides, heat exchanger partsOxidising and high chloride conditions at the same time
Pulp and paperBlack liquor evaporator bodies and internals in kraft millsAlkaline chloride cracking resistance at temperature
PowerFlue gas desulphurisation absorbers and ducting componentsAcidic chloride condensate
Water treatmentDemineralised water plant, waste water, high salinity process equipmentDesign life in chloride bearing water
07

Standards, testing, certification

Product standards listing S32654 and 1.4652
FormASTM / ASMEEuropean
Plate, sheet, stripA240 / SA240EN 10088
Seamless pipeA312EN 10216-5
Heat exchanger tubeA213EN 10216-5
General tubingA269—
Welded tubeA249EN 10217-7
Forgings and rolled ringsSupplied to the grade chemistry and property requirements with A182 style supplementary requirements applied by agreement. Tell us the exact forging specification your project names and we will confirm in writing whether we can certify to it before you place the order.
Inspection and documents
CheckStandard or scope
Ultrasonic testingEN 10228-3, SEP 1921, ASTM A388
Chemical analysisOptical emission spectrometry on every heat; handheld PMI on request
Mechanical testingTensile, yield, elongation, hardness; Charpy impact on request
Corrosion testingASTM G48 pitting and critical pitting temperature, placed with an accredited laboratory
CertificationEN 10204 3.1 as standard. 3.2 witnessed by BV, DNV, LR, SGS or TUV on request
Works approvalsCCS, BV, DNV, LR, NK
DimensionalFull report against customer drawing
08

Questions we are asked

Is S32654 a powder metallurgy steel?

No, and this is worth correcting because the claim is copied across a number of supplier pages. S32654 is a conventionally melted wrought stainless steel. We produce forging stock by electric arc melting with ladle refining and vacuum oxygen decarburisation, with electroslag remelting added where the specification asks for it.

How does it differ from 254 SMO?

S32654 carries 7 to 8 percent molybdenum against roughly 6 in S31254, more chromium, and about twice the nitrogen. That buys both a higher PREN and a considerably higher yield strength. The usual trigger for switching is a 6 percent molybdenum grade that has already pitted in service, or a duty where the design seawater temperature rules one out on paper.

Can it replace a nickel alloy or titanium?

In a lot of chloride service its localised corrosion resistance is in the same band as the better nickel alloys, and it is regularly evaluated as a cheaper substitute in seawater and brine systems. Whether the swap holds depends on the actual temperature, chloride level, pH, and whether reducing acids or hydrogen sulphide are present. It is a case-by-case decision, not a general rule.

Do you hold S32654 in stock?

Not as finished forgings. This grade is made to order against the drawing, which is the normal arrangement for a 7 percent molybdenum alloy. Lead time runs 20 to 60 days depending on size, heat treatment and testing scope.

What do you need to quote?

Finished size or forged size, or a drawing. Quantity. The specification the project names. Any testing beyond our standard scope, and whether 3.1 or 3.2 certification is required. Quotations normally go back within one working day.

Request a quotation

Send the drawing or the dimensions and we will come back with price, forging route and delivery. Jiangyin Jiangnan Metal Co., Ltd. has melted and forged steel at this site since 1997.

Works
No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province 214423, China
Telephone, WhatsApp, WeChat
Email
Works data
460 staff · 60 t heat · 6,300 t press · 6 m ring mill · CCS BV DNV LR NK