Jiangyin Jiangnan Metal Co., Ltd. Open-Die Forging Factory, Jiangyin, Jiangsu, China

UNS S31050 Forgings: EN 1.4466 / X1CrNiMoN25-22-2 / 310MoLN

Open-die forged rings, flanges, bars, discs, shafts and tube sheets in urea grade austenitic stainless steel. ASTM A182 grade F310MoLN. Made to drawing by Jiangyin Jiangnan Metal Co., Ltd.

UNS S31050 is a fully austenitic chromium-nickel-molybdenum stainless steel with low carbon (0.030 % max) and controlled nitrogen (0.10 to 0.16 %), nominally 25 % Cr, 22 % Ni, 2 % Mo. In Europe it is EN 1.4466 / X1CrNiMoN25-22-2; in the trade it is usually called 310MoLN. The grade was developed for urea and nitric acid service, where the low carbon and high chromium give resistance to carbamate corrosion and to intergranular attack after welding. For forgings the governing specification is ASTM A182 grade F310MoLN.

Jiangyin Jiangnan Metal Co., Ltd. is an open-die forging factory in Jiangyin, Jiangsu, China. We forge UNS S31050 to customer drawing in the shapes below, heat treat and test in house, and release with EN 10204 3.1 or 3.2 certification.

Forged shapes in UNS S31050

Rings and seamless rolled rings

Forged rings and seamless rolled rings for flanged joints, housings and pressure retaining shells.

Flanges and tube sheets

Forged flanges, blinds, tube sheets and nozzles for carbamate condensers, strippers and heat exchangers.

Round bars and hollow bars

Forged round bar, hollow bar and forged tube or pipe blanks for machining.

Discs, disks and blocks

Forged discs, disks, blocks and forging pieces for valve and pump parts.

Shafts, spindles and gears

Forged shafts, eccentric shafts, spindles, gear blanks and rolls for compressors, pumps and drives.

Sleeves and bushings

Forged sleeves, bushings and wear rings for corrosive and erosive duty.

Valve components

Valve bodies, bonnets, stems, seat rings and blocks for ball, gate, globe, check and plug valves.

Custom open-die work

Non standard geometry, stepped shafts, manifolds, wheels and crankshafts to drawing.

Chemical composition

Composition limits, ASTM A182 grade F310MoLN (UNS S31050), weight %
CMnPSSiCrNiMoNFe
0.030 max2.00 max0.030 max0.015 max0.40 max 24.0–26.021.0–23.02.00–3.000.10–0.16Balance

Source: ASTM A182 / A182M, grade symbol F310MoLN, UNS S31050. EN 1.4466 limits are close but tighten S to 0.010 max and Mo to 2.00–2.50. A nominal mill analysis for the equivalent Alleima 2RE69 is C 0.020 max, Si 0.4 max, Mn 1.7, P 0.015 max, S 0.010 max, Cr 25, Ni 22, Mo 2.1, N 0.12.

On the nitrogen: the 0.10 to 0.16 % N addition stabilises and strengthens the austenite phase. That is what lets the grade work in urea carbamate service at only about 2 % Mo. A UNS S31050 datasheet that omits nitrogen, or that shows single digit nickel, is describing a different material.

Mechanical properties

Minimum room temperature properties for forgings, ASTM A182 F310MoLN
PropertyMetricImperial
Tensile strength, min540 MPa78 ksi
Yield strength, 0.2 % offset, min255 MPa37 ksi
Elongation in 2 in. or 4D, min25 %25 %
Reduction of area, min40 %40 %

Source: ASTM A182 / A182M, grade F310MoLN. For comparison, EN 1.4466 bar and plate is generally quoted at Rp0.2 250 MPa min with Rm 540–740 MPa. Alleima quotes Rp0.2 270 MPa min and Rm 580–780 MPa for 2RE69 tube and pipe and notes that lower values can apply to bar, plate, sheet and forgings.

Physical properties

Typical values at 20 °C
PropertyValue
Density7.9 g/cm³ (0.29 lb/in³)
Modulus of elasticity195 GPa (28.3 × 10³ ksi)
Thermal conductivity13–14 W/m·°C
Specific heat capacity485–500 J/kg·°C
Mean thermal expansion, 30–100 °C15.5 × 10⁻⁶ /°C
Relative magnetic permeabilityabout 1.003
Hardness95 HRB max (Alleima 2RE69)

Sources: Metalcor 1.4466 datasheet, Alleima 2RE69 datasheet. Thermal conductivity is low and expansion is high, as with other fully austenitic grades, so allow for distortion when welding and machining.

Equivalent grades and designations

Cross reference for UNS S31050
SystemDesignation
UNSS31050
EN material number1.4466
EN nameX1CrNiMoN25-22-2
Common name310MoLN
ASTM A182 grade symbolF310MoLN
AFNORZ1 CND 25.22 AZ
DIN, obsoleteX2 CrNiMo 25 22 2
Proprietary namesAlleima 2RE69 (formerly Sandvik), Industeel UREA 310Mo LN, also sold as 725LN
Related higher alloy gradeEN 1.4465 / X1CrNiMoN25-25-2 (25Cr 25Ni 2Mo)

Sources: Alleima 2RE69 standards list, Metalcor 1.4466, Virgamet 1.4466 / 310MoLN. Do not confuse the grade with UNS S31002 (310L, 2RE10), which carries no molybdenum addition.

Heat treatment after forging

UNS S31050 is supplied solution annealed. Corrosion performance depends on keeping chromium carbides out of the grain boundaries, so the cooling rate matters as much as the soak temperature.

Published solution annealing practice
SourceTemperatureHold and cooling
Alleima, 2RE69 (S31050)1070–1120 °C (1960–2050 °F)5–15 min depending on size, then rapid cooling in water or air
Industeel, UREA 310Mo LN plate1140–1180 °C (2084–2156 °F)Final full annealing followed by water quenching

Hot working of the equivalent 2RE69 is carried out between 1100 and 850 °C. On forged sections we set the final cycle with you, or directly against the urea licensor specification, and record the furnace chart on the certificate. Hot bending is normally done without subsequent heat treatment. Where residual stress is a concern, solution annealing after welding is available.

Sources: Alleima 2RE69 datasheet, heat treatment and fabrication sections. Industeel UREA 310Mo LN datasheet.

Corrosion resistance

The grade was developed for the hardest duty in the urea process. Published data for the equivalent Alleima 2RE69 covers the following mechanisms.

MechanismBehaviour
Urea and carbamate corrosionExcellent resistance in urea carbamate solutions at high pressure and temperature. This is the service the grade was designed for.
Nitric acidHighly resistant to inorganic acids. Iso-corrosion performance in aerated nitric acid is better than ASTM 304L.
Intergranular corrosionHighly resistant after welding. Huey test values on TIG welded, unsensitised specimens are typically below 0.12 mm per year, with selective attack usually under 10 µm.
Pitting and crevice corrosionCritical pitting temperature in neutral chloride solution is higher than ASTM 316L. Crevice resistance is also considerably better than 316L.
Chloride stress corrosion crackingSlightly more resistant than 304 and 316 types in laboratory tests because of the higher nickel. Conventional 304 and 316 become susceptible above roughly 60 °C in chloride bearing solutions.
Erosion corrosionGood strength gives useful erosion corrosion resistance, which is why the grade is used for urea stripper ferrules.

Source: Alleima 2RE69 datasheet, corrosion resistance section. The data applies to that proprietary tube product. Forged material from any mill should be qualified against your own service conditions and licensor requirements.

Applications for UNS S31050 forgings

Urea and fertiliser plants

High pressure urea units are the main application: stripper tubes and ferrules, carbamate condensers, decomposers and reactor coils. Alleima lists 2RE69 against urea specifications issued by Stamicarbon, Saipem, Kellogg and Urea Casale, and records ASME Boiler and Pressure Vessel Code Section VIII Divisions 1 and 2 approval together with ASME Code Case 2038-5 for forgings, which is the route that applies to forged flanges, tube sheets and high pressure fittings. Outside urea, the grade is used in nitric acid coolers and condensers cooled with polluted cooling water, and in heating coils and pipe in NPK plants.

Other process industries

Forged tube sheets, flanges, shells and nozzles for separators and heat exchangers. Components for pulp and paper, chemical and pharmaceutical production, waste treatment thermal oxidisers and seawater desalination. Forged valve bodies, stems and seat rings for corrosive service. Forged rings and shafts for compressors, pumps and power transmission assemblies.

Welding and overlay

For weld overlay that must match the base metal, ISO 14343 S 25 22 2 N L wire or strip electrodes are recommended for tube sheets and high pressure vessels. For fusion welding, TIG or GTAW is the first choice, with no preheat, heat input below about 1.0 kJ/mm, interpass temperature below 100 °C and a string bead technique.

Source: Alleima 2RE69 datasheet, welding section. Metalcor lists filler 1.4455 for 1.4466.

Manufacturing and quality

ItemScope
Melting routeEAF + VOD, ESR remelt on request
FormingOpen-die forging, ring rolling for seamless rolled rings, upsetting, drawing out
Heat treatmentSolution annealing with water or air quench, furnace charts recorded
Ultrasonic testingEN 10228-3, SEP 1921, ASTM A388
Other NDTLiquid penetrant, dimensional inspection, PMI on request
Mechanical testingTensile, impact, hardness. The austenitic structure holds good impact toughness down to cryogenic temperature.
Corrosion testingIntergranular corrosion and Huey type testing to the applicable specification, on request
CertificationEN 10204 3.1, or 3.2 with third party witness
MachiningRough or finish machining to drawing. Cutting speeds have to be reduced against 316L for this grade.

Melting, NDT, certification and machining items describe the capability of Jiangyin Jiangnan Metal Co., Ltd. The toughness and machinability remarks reflect published behaviour of the grade in the Alleima 2RE69 datasheet.

Frequently asked questions

Is UNS S31050 a duplex stainless steel?
No, it is fully austenitic. Nickel at 21 to 23 % plus 0.10 to 0.16 % nitrogen stabilises the austenite. It is often mixed up with duplex grades such as A182 F51 (S31803) and A182 F53 (S32750), which hold far less nickel and have a two phase austenitic-ferritic structure.
What is the difference between S31050 (310MoLN) and S31002 (310L, 2RE10)?
Both are low carbon 25 Cr austenitic grades. S31050 adds 2 to 3 % molybdenum and 0.10 to 0.16 % nitrogen, which is what suits it to urea carbamate service. S31002 has no molybdenum addition and is aimed mainly at nitric acid.
Which specification should forgings be ordered to?
ASTM A182 / A182M grade F310MoLN covers pipe flanges, forged fittings, valves and pressure parts. European equivalents sit under EN 10088-3 for bars and semi-finished products, EN 10028-7 for flat pressure products and EN 10216-5 for seamless tube. Alleima also cites SEW 400 and ASME Code Case 2038-5 for forgings.
What is the maximum size you can forge?
It depends on the geometry and the ingot available in this grade. Send the drawing with finished dimensions and we will confirm forged weight, achievable envelope and lead time before you commit.
Can you supply certificates and third party inspection?
Yes. EN 10204 3.1 as standard, and EN 10204 3.2 with a third party inspector such as a classification society or your own nominated agency.
Is S31050 magnetic?
Effectively non magnetic in the solution annealed condition. Relative magnetic permeability is about 1.003 for the equivalent 2RE69.
What do you need for a quotation?
Drawing or OD, ID, length and thickness, quantity, governing specification, heat treatment condition, NDT level and certificate type. Email sales@steelforgepieces.com or call +86-189-2135-9659.

Request a quotation

Jiangyin Jiangnan Metal Co., Ltd., open-die forging factory
No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Phone +86-189-2135-9659
Email sales@steelforgepieces.com

Send your drawing for a quotation

Data sources

Composition and mechanical requirements on this page follow ASTM A182 / A182M grade F310MoLN (UNS S31050). Heat treatment, corrosion, welding and physical property data is taken from the Alleima 2RE69 (UNS S31050) material datasheet, the Metalcor 1.4466 / 310MoLN datasheet, the AZoM 310 MoLN datasheet and the Industeel UREA 310Mo LN datasheet. Designations follow EN 10088 and EN 10216-5. Manufacturing, testing and certification scope is that of Jiangyin Jiangnan Metal Co., Ltd. Page updated 5 October 2026.