AISI 317LM Forgings: UNS S31725 / ASTM A182 Grade F47

Rolled rings, forged flanges, round bars, shafts, discs, sleeves and tube sheets, open-die forged to drawing by Jiangyin Jiangnan Metal Co., Ltd.

Grade in short. AISI 317LM is a low-carbon, high-molybdenum austenitic stainless steel, UNS S31725, listed in ASTM A182/A182M as forging grade F47. The forging chemistry is 18.0-20.0 % Cr, 13.0-17.5 % Ni, 4.0-5.0 % Mo, carbon 0.030 % max and nitrogen 0.10 % max. The molybdenum level puts the calculated PREN near 35, well above 304 and 316, and the grade was developed in particular to handle sulfuric acid compounds. It stays fully austenitic, is not hardenable by heat treatment, and forges readily.

Where to buy. Jiangyin Jiangnan Metal Co., Ltd., No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China, forges 317LM / S31725 / A182 F47 to customer drawing with EN 10204 3.1 or 3.2 certification and ultrasonic testing to EN 10228-3, SEP 1921 or ASTM A388. Enquiries: sales@steelforgepieces.com, +86 189-2135-9659.

1. Designations and equivalents

AISI 317LM cross-reference. Confirm the standard and edition on the order.
SystemDesignationRemarks
AISI / trade name317LMAlso written 317 LM, 317LMG
UNSS31725Primary identifier
ASTM A182/A182MF47Forged flanges, fittings, valves and parts
Other ASTM product formsA240 plate, A276 and A479 bar, A312, A213, A249, A269 tube and pipe, A358, A376, A409, A167Same chemistry, different product-form rules
EN reference1.4439 / X2CrNiMoN17-13-5Conversion tables disagree, see note below
Neighbouring grades317L (S31703, EN 1.4438), 317LMN (S31726)317LMN is the nitrogen-alloyed version
Cross-reference note. EN 1.4439 / X2CrNiMoN17-13-5 is a nitrogen-bearing grade normally tied to 317LMN / UNS S31726, yet some distributor conversion tables also list it against 317LM / S31725. EN 1.4438 (X2CrNiMo18-15-4) is the grade usually paired with 317L / S31703. Because the nitrogen requirement differs, state the exact specification, edition and UNS number on your enquiry. We certify to the document you name, not to a trade name.

2. Chemical composition

Weight %, single values are maxima.
ElementASTM A182 F47 / S31725General 317LM datasheet
Carbon, C0.030 max0.03 max
Chromium, Cr18.0 - 20.018 - 20
Nickel, Ni13.0 - 17.512 - 16
Molybdenum, Mo4.0 - 5.04 - 5
Manganese, Mn2.00 max2.00 max
Silicon, Si0.75 max1.00 max
Nitrogen, N0.10 maxnot specified
Phosphorus, P0.045 max0.045 max
Sulfur, S0.030 max0.03 max
Iron, FeBalanceBalance

The two columns differ in the nickel and silicon windows because the A182 forging table and the general grade datasheet were written for different product scopes. For forgings the A182 F47 column governs. Pitting resistance equivalent, calculated as %Cr + 3.3 x %Mo + 16 x %N, works out at roughly 35 for this chemistry.

3. Mechanical properties

Room temperature minima, solution annealed condition.
PropertyASTM A182 F47 forgingsPlate and general datasheet
Tensile strength, min525 MPa / 75 ksi515 MPa / 74 ksi
Yield strength 0.2 %, min205 MPa / 30 ksi205 MPa / 30 ksi
Elongation, min40 % in 2 in. or 4D35 %
Reduction of area, min50 %not specified
Hardness, annealedabout 95 HRB
Modulus of elasticity190 - 210 GPa
Poisson's ratio0.27 - 0.30
Density7.7 - 8.03 g/cm3
A point often mixed up in online tables: A182 F47 forgings call for 40 % elongation and 50 % reduction of area, while the 35 % figure belongs to plate. Testing and reporting follow whichever product standard your order names.

4. Forging, heat treatment, machining, welding

Hot working

Heat to 1149-1260 C (2100-2300 F). Do not continue working below about 927 C (1700 F). A post-work anneal is advised for optimum corrosion resistance.

Solution annealing

Soak at 1121-1149 C (2050-2100 F), then water quench. The grade takes no hardening heat treatment; strength rises only through cold reduction.

Machining

Low speeds and constant feed keep work hardening down. 317LM is tougher than 304 and throws a long stringy chip, so chip breakers are recommended.

Welding

All conventional processes apply. Published filler recommendations are 317L or alloy 625 type consumables where matching or over-alloyed weld metal is wanted.

Forming takes roughly twice the force of a standard austenitic grade, ample radii should be allowed in roll forming, and cuts have to go through the full thickness because the material does not snap.

5. Corrosion behaviour

317LM was designed against sulfuric acid attack, and the 4-5 % molybdenum also lifts resistance to chlorides, pitting and crevice corrosion compared with 304 and 316. Carbon held at 0.030 % max limits chromium carbide precipitation at grain boundaries, so corrosion resistance survives welding without a stabilising addition.

The grade suits wet corrosive duty below the range normally treated as high temperature service. Like every austenitic stainless steel it can still suffer chloride stress corrosion cracking, though it holds up better than 304 or 316. Where stress corrosion cracking is the governing risk, duplex grades such as F51, F53 and F55, or nickel alloys such as 625 and C-276, may be the sounder choice. We forge those too and will say so at enquiry stage rather than after the order.

6. Applications

Published service areas for the grade cover pulp and paper, textile and food processing equipment, flue gas scrubbers, and process equipment handling dyestuffs, rubber, rayon, ink, chemicals and bleaches. In forged form the usual items are:

Forged shapes supplied in AISI 317LM.
Forged formTypical use
Rolled rings, forged ringsScrubber and vessel shell courses, reinforcement rings, bearing and seal housings
Flanges, nozzles, tube sheetsPressure vessels, air receivers, shell and tube heat exchangers, columns and towers
Round bars, hollow bars, sleeves, bushingsPump and agitator parts, wear sleeves, machined fittings
Shafts, spindles, stemsDigesters, mixers, chemical process drives
Discs, blanks, valve bodies, seat ringsBall, gate, globe, check and plug valves in chemical service
Custom open-die shapesMade to drawing, single pieces through to repeat batches

7. Manufacturing and inspection

Order and quality parameters for AISI 317LM forgings.
Raw material melting routeEAF + AOD or VOD, with ESR where the specification or customer calls for it
ProcessesOpen-die forging, ring rolling, upsetting and piercing, rough and finish machining
Delivery conditionSolution annealed; as forged, rough machined or finish machined as agreed
Size rangeState the finished outside diameter, wall and single piece weight on the enquiry and we confirm feasibility by return
Non-destructive testingUltrasonic to EN 10228-3, SEP 1921 or ASTM A388; PT, PMI and hardness survey on request
CertificationEN 10204 3.1 mill certificate, or 3.2 with third party witness on request
Supplementary testsIntergranular corrosion to ASTM A262, impact testing, grain size, macro and micro examination

Request a quotation

Send a drawing, a sketch, or just dimensions, quantity and the governing standard (A182 F47, A240, A479 and so on). Price and lead time normally come back within one working day.

sales@steelforgepieces.com +86 189-2135-9659

Jiangyin Jiangnan Metal Co., Ltd., No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China

8. Questions we are asked

What is AISI 317LM?

A low-carbon, high-molybdenum austenitic stainless steel, UNS S31725, listed in ASTM A182/A182M as forging grade F47. Composition runs 18.0-20.0 % Cr, 13.0-17.5 % Ni, 4.0-5.0 % Mo with carbon at 0.030 % max, which buys better pitting and sulfuric acid resistance than 304 or 316.

Is 317LM the same as A182 F47?

Yes. F47 is the grade symbol ASTM A182/A182M gives the S31725 chemistry for forged flanges, fittings, valves and parts. Minima are 525 MPa tensile, 205 MPa yield, 40 % elongation, 50 % reduction of area.

How does 317LM differ from 317L and 317LMN?

317L (S31703) is the base low-carbon molybdenum grade. 317LM (S31725) carries 4.0-5.0 % Mo with higher nickel for sulfuric acid and chloride duty. 317LMN (S31726) adds nitrogen for higher strength and further pitting resistance, and is the grade usually matched to EN 1.4439.

Can 317LM be hardened by heat treatment?

No. It is fully austenitic and strengthens only by cold reduction. Heat treatment is limited to solution annealing at 1121-1149 C with a water quench.

Does 317LM crack in chloride service?

It remains susceptible to chloride stress corrosion cracking, though it resists better than 304 and 316. For severe chloride duty consider duplex grades F51, F53, F55 or nickel alloys 625 and C-276.

Who forges AISI 317LM in China?

Jiangyin Jiangnan Metal Co., Ltd., an open-die forging factory at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China, supplies 317LM / S31725 / A182 F47 rolled rings, flanges, bars, shafts, discs, sleeves and tube sheets to drawing, with EN 10204 3.1 or 3.2 certification and ultrasonic testing to EN 10228-3, SEP 1921 or ASTM A388. Write to sales@steelforgepieces.com or call +86 189-2135-9659.

AISI 317LM A182 F347 A182 F321 A182 F44 A182 F51 A182 F53 A182 F55 A182 F61 904L Sanicro 28 Alloy 24 Inconel 625 Hastelloy C-276 Alloy 20

Figures on this page are compiled from the ASTM A182/A182M grade table for F47 (UNS S31725) and from published 317LM grade datasheets; where the forging standard and the general datasheet disagree, both are shown. The material test certificate issued with your order is the governing document. Page reviewed .

Nickel alloy grades we also forge