X2CrNiMoN18-14-3 (1.3952) Forgings: Rings, Flanges, Bars and Discs
Non-magnetizable nitrogen-alloyed austenitic Cr-Ni-Mo stainless steel, open-die forged to drawing by Jiangyin Jiangnan Metal Co., Ltd.
X2CrNiMoN18-14-3 is a non-magnetizable austenitic stainless steel with the material number 1.3952, listed in SEW 390 and in the WL 1.3952 sheet series. It contains max 0.03 % C, 16.50 to 18.50 % Cr, 13.00 to 15.00 % Ni, 2.50 to 3.00 % Mo and 0.15 to 0.25 % N, and its relative magnetic permeability stays below 1.01. Jiangyin Jiangnan Metal Co., Ltd. open-die forges this grade into rings, seamless rolled rings, flanges, round bars, discs, shafts, sleeves, bushings and tube sheets, supplied with EN 10204 3.1 or 3.2 certification.
The grade
X2CrNiMoN18-14-3 belongs to the group of non-magnetizable steels. The designation is tied to material number 1.3952, which appears in SEW 390 (Stahl-Eisen-Werkstoffblatt 390) and in the WL material sheet series, where WL 1.3952-3 covers bars and describes the steel as a non-magnetizable austenitic seawater-resistant grade for vessel components.
What separates it from an ordinary 316L-type austenitic is the magnetic behaviour. Relative magnetic permeability stays below 1.01, so the steel does not distort nearby magnetic fields. Published material data for 1.3952 also records resistance to intercrystalline corrosion, pitting and stress corrosion cracking, with intercrystalline corrosion resistance retained after welding. The steel is weldable, machines well, and resists erosion corrosion. Documented use is for parts in ship construction.
Chemical composition
| C | Si | Mn | P | S | Cr | Mo | Ni | N |
|---|---|---|---|---|---|---|---|---|
| max 0.03 | max 1.00 | max 2.00 | max 0.045 | max 0.015 | 16.50 to 18.50 | 2.50 to 3.00 | 13.00 to 15.00 | 0.15 to 0.25 |
No deliberate additions of V, W, Ti, Cu, Al, Nb or B are specified. Balance is iron with residual elements. Nitrogen is the intentional addition: it stabilises the austenite, raises the proof strength, and together with molybdenum lifts localised corrosion resistance above a plain 316L chemistry.
Calculated PREN
With the usual formula PREN = %Cr + 3.3 × %Mo + 16 × %N, the specification limits give roughly 27 at the low end and 32 at the high end. This is a calculated comparison index taken from the composition range, not a guaranteed property. If your specification sets a minimum PREN, tell us the figure and we will aim the heat chemistry accordingly and report the calculated value on the certificate.
Mechanical properties
| Thickness t, mm | Direction | Rm, MPa | Rp0.2, MPa | A, % |
|---|---|---|---|---|
| 3 to 75 | transverse | 580 to 800 | 295 min | 35 min |
| 3 to 75 | longitudinal | 580 to 800 | 295 min | 35 min |
| up to 6 | transverse | 580 to 800 | 315 min | 40 min |
| up to 6 | longitudinal | 580 to 800 | 300 min | 38 min |
Supplier data sheets for the same material number also quote tensile strength 580 to 800 MPa with 280 MPa minimum proof strength and 30 % minimum elongation as a general figure covering heavier sections. Values for heavy open-die forgings depend on section size, forging ratio and test position, so we agree the sampling location, orientation and acceptance limits with you before production starts and report the measured results on the certificate.
Forged products in X2CrNiMoN18-14-3
Everything below is made to customer drawing or specification at our Jiangyin plant, as open-die forgings or seamless rolled rings.
Rings
Forged rings, seamless rolled rings, retaining rings, spacer rings, gear blanks and bearing ring blanks.
Flanges and discs
Forged flanges, blind and weld-neck blanks, discs, tube sheets, nozzle blanks and manifold blocks.
Bars and shafts
Forged round bars, step shafts, eccentric shafts, spindles, pump shafts and crankshaft blanks.
Hollow sections
Forged bushings, sleeves, forged tubes and forged pipe sections, bored or trepanned as needed.
Valve parts
Valve bodies, bonnets, stems, blocks and valve seat rings for ball, gate, globe, check and plug valves.
Other shapes
Forged wheels, rolls, couplings, blocks and custom profiles, delivered as forged, rough machined or finish machined.
Where the grade is used
This steel is chosen when a part has to resist corrosion and stay magnetically neutral at the same time. The documented application is ship construction, and the WL sheet describes the material as a non-magnetizable austenitic seawater-resistant steel for vessel components. Permeability below 1.01 combined with resistance to pitting, intercrystalline corrosion and stress corrosion cracking also makes it a candidate for housings and structures around sensitive measuring and navigation equipment, for marine and offshore hardware in contact with seawater, and for welded fabrications that have to resist intergranular attack in the as-welded condition.
If your application sits outside those uses, send us the service conditions: temperature, medium, chloride content, stress state and any permeability limit you have to meet. We will say plainly whether 1.3952 suits the job or whether a duplex grade such as A182-F51, a super duplex such as A182-F55, a 6 % Mo austenitic such as A182-F44 or a nickel alloy such as Inconel 625 would serve you better.
Melting, forging and testing
Melting
We melt this grade by EAF plus VOD. Electro-slag remelting (ESR) is available where cleanliness, reduced segregation or tighter ultrasonic acceptance levels are required. Nitrogen is controlled during refining to hold the 0.15 to 0.25 % band.
Forging and heat treatment
Ingot or billet is open-die forged with a controlled forging ratio to break down the cast structure, then solution annealed and water quenched to dissolve carbides and restore both corrosion resistance and the fully austenitic, non-magnetic structure. Pickling or passivation can be added on request.
Non-destructive testing
Ultrasonic examination follows EN 10228-4, the part of the EN 10228 series written for austenitic and austenitic-ferritic stainless steel forgings. EN 10228-3 covers ferritic and martensitic forgings and is not the right reference for this grade, which is worth checking if an older enquiry document calls it out. Where a US specification is preferred we test to ASTM A388. Liquid penetrant testing to EN ISO 3452 or ASTM E165 is available for surface examination. Magnetic particle testing does not apply to a non-magnetizable austenitic steel.
Certification
Material is supplied with an EN 10204 Type 3.1 inspection certificate issued by our works inspection department, or a Type 3.2 certificate countersigned by a third-party inspector or your nominated representative when the purchase order calls for it.
Designations and related grades
| Designation | Material number | Note |
|---|---|---|
| X2CrNiMoN18-14-3 | 1.3952 | This page. Non-magnetizable austenitic grade under SEW 390 and WL 1.3952. Also written X2CrNiMnMoN18-14-3 in some sources. |
| X2CrNiMoN17-13-3 | 1.4429 | Different grade. AISI 316LN, UNS S31653. |
| X2CrNiMo18-14-3 | 1.4435 | Different grade. 316L type with similar Cr, Ni and Mo but without the nitrogen addition. |
European mills and stockists market material 1.3952 under their own names. Confirmed examples include AMANOX 3952 (Outokumpu Nirosta, Krefeld), ARGESTE 1.3952 (Zapp Precision Metals, Schwerte) and BGH 3952 (BGH Edelstahl). The list is not complete. If a drawing you hold quotes a trade name we have not listed, send it over with the material number and we will quote against it.
What to send with an enquiry
To price X2CrNiMoN18-14-3 forgings quickly we need the grade and material number, the drawing or finished dimensions with machining allowance, quantity and required delivery date, the delivery condition (as forged, rough machined, solution annealed, pickled), whether ESR is required, the NDT level to EN 10228-4 or ASTM A388, any permeability limit, and the certificate type. A dimensioned sketch is enough for a budget price. A full drawing is only needed at order stage.
Common questions
What is the material number of X2CrNiMoN18-14-3?
1.3952, listed in SEW 390 and in the WL 1.3952 sheet series, where WL 1.3952-3 covers bars. It is not 1.4429, which is designated X2CrNiMoN17-13-3 and matches AISI 316LN / UNS S31653.
Is X2CrNiMoN18-14-3 magnetic?
No. It is a non-magnetizable steel with relative magnetic permeability below 1.01, which is why it is specified for parts that must not disturb magnetic fields or sensitive instruments.
What is the PREN of X2CrNiMoN18-14-3?
Calculated from the specification limits with PREN = %Cr + 3.3 × %Mo + 16 × %N, the range is about 27 to 32. It is a calculated index for comparing pitting resistance, not a measured value.
Can the grade be welded?
Yes. Published material data describes it as weldable and records that resistance to intercrystalline corrosion is kept in the welded condition. Filler metal should be agreed with your welding engineer against the applicable procedure and service environment.
Which ultrasonic standard applies?
EN 10228-4, which covers austenitic and austenitic-ferritic stainless steel forgings. EN 10228-3 is for ferritic and martensitic forgings and should not be quoted for this grade. ASTM A388 is used where a US standard is required.
What sizes can you forge?
Size capability depends on the shape and the ingot available. Send the drawing or finished dimensions with machining allowance to sales@steelforgepieces.com and we will confirm feasibility, piece weight and lead time for your part.
Who supplies X2CrNiMoN18-14-3 forgings from China?
Jiangyin Jiangnan Metal Co., Ltd., an open-die forging factory at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China, produces X2CrNiMoN18-14-3 forged rings, flanges, bars, discs, shafts, sleeves and tube sheets to customer drawing, with EN 10204 3.1 or 3.2 certification. Telephone 0086-189-2135-9659, email sales@steelforgepieces.com.
Related grades
Quotation for X2CrNiMoN18-14-3 forgings
Send your drawing or dimensions to Jiangyin Jiangnan Metal Co., Ltd., open-die forging factory in Jiangyin, Jiangsu, China. You will get a price, piece weight and lead time.