XM-19 Forgings (UNS S20910 / Nitronic 50)
Forged rings, seamless rolled rings, flanges, shafts, discs, sleeves, bushings, tube sheets and round bars, made to drawing by Jiangyin Jiangnan Metal Co., Ltd., an open-die forging factory in Jiangyin, Jiangsu, China.
XM-19 is a nitrogen-strengthened austenitic stainless steel, numbered UNS S20910 and sold under the trade name Nitronic 50. It gives corrosion resistance equal to or better than types 316, 316L, 317 and 317L while carrying roughly twice their room-temperature yield strength, and it stays essentially non-magnetic after cold work. Jiangyin Jiangnan Metal Co., Ltd. supplies XM-19 as open-die forgings and seamless rolled rings, melted by EAF plus VOD with ESR remelt where the specification calls for it, solution annealed, ultrasonically tested and certified to EN 10204 3.1 or 3.2.
Key data
- Designations
- XM-19, XM19, UNS S20910, Nitronic 50, ASTM A182 FXM-19, 22Cr-13Ni-5Mn
- Alloy type
- Nitrogen-strengthened austenitic stainless steel
- Nominal chemistry
- 22Cr, 12.5Ni, 5Mn, 2Mo, 0.3N, plus Nb and V
- Tensile, annealed
- 690 MPa / 100 ksi minimum
- 0.2% yield, annealed
- 380 MPa / 55 ksi minimum
- Elongation / R.A.
- 35% / 55% minimum
- Hardness, annealed
- 293 HBW maximum
- Density
- 7.88 g/cm3 (0.285 lb/in3)
- Forging range
- 1177-1204 C (2150-2200 F)
- Solution anneal
- 1066-1121 C (1950-2050 F), water quench
- Sour service
- Listed in NACE MR0175 / ISO 15156-3 to 35 HRC maximum
- Manufacturer
- Jiangyin Jiangnan Metal Co., Ltd., Jiangyin, Jiangsu, China
What XM-19 is
XM-19 is an austenitic, non-magnetic stainless steel strengthened with nitrogen, manganese and molybdenum, with small niobium and vanadium additions. The nitrogen does most of the work. It lifts the yield strength to about double that of the ordinary 300-series austenitics at room temperature, which matters because the grade cannot be hardened by heat treatment. Chromium at 20.5 to 23.5 per cent, together with the molybdenum, provides resistance to intergranular corrosion, pitting and chloride attack, seawater, sulphur compounds and nitric, phosphoric and dithionic acids.
Two things set it apart from other austenitic grades. It does not turn magnetic when cold formed, so it is used where magnetic permeability has to stay low. And it holds its properties at both ends of the temperature scale, with published impact energy above 255 J at minus 40 C and above 75 J at minus 195 C, which makes it a usable cryogenic forging material.
XM-19, Nitronic 50 and UNS S20910
These are three names for one alloy. XM-19 is the ASTM designation used in A182, A276, A479 and the related product standards. UNS S20910 is the unified number. Nitronic 50 is a trade name. Published limits differ slightly between the branded datasheets and the UNS entry, for instance silicon at 0.75 per cent maximum against 1.00 per cent maximum. State the controlling specification on your order and we certify to that document.
Chemical composition of XM-19
| Element | Symbol | Content (%) |
|---|---|---|
| Carbon | C | 0.06 max |
| Manganese | Mn | 4.00 - 6.00 |
| Silicon | Si | 1.00 max |
| Phosphorus | P | 0.040 max |
| Sulphur | S | 0.030 max |
| Chromium | Cr | 20.50 - 23.50 |
| Nickel | Ni | 11.50 - 13.50 |
| Molybdenum | Mo | 1.50 - 3.00 |
| Niobium (columbium) | Nb | 0.10 - 0.30 |
| Vanadium | V | 0.10 - 0.30 |
| Nitrogen | N | 0.20 - 0.40 |
| Iron | Fe | Balance |
On sulphur: UNS S20910 and the ASTM product standards allow 0.030 per cent maximum, while some branded Nitronic 50 datasheets quote 0.010 per cent maximum. If your drawing needs the tighter limit, write it on the order and we will melt to it.
Mechanical properties of XM-19
Three delivery conditions are in common use. Annealed is the normal condition for forgings. Hot-rolled high strength and strain-hardened conditions apply mainly to bar.
| Condition | Tensile Rm | Yield Rp0.2 | Elongation A | Reduction of area Z | Hardness |
|---|---|---|---|---|---|
| Annealed | 690 MPa (100 ksi) | 380 MPa (55 ksi) | 35% | 55% | 293 HBW max |
| Hot-rolled, high strength | 690 MPa | 415 MPa | 30% | 50% | - |
| Strain hardened | 825 MPa | 725 MPa | 15% | 45% | - |
Elevated and sub-zero temperature data
| Temperature | Rm | Rp0.2 | Elongation | Impact KV |
|---|---|---|---|---|
| -195 C | 1550 MPa | 880 MPa | 41% | above 75 J |
| -70 C | 1000 MPa | 580 MPa | 49% | - |
| -40 C | - | - | - | above 255 J |
| +20 C | 830 MPa | 390 MPa | 45% | above 270 J |
| +200 C | 720 MPa | 320 MPa | 38% | - |
| +650 C | 570 MPa | 290 MPa | 36% | - |
Physical properties
| Property | Value |
|---|---|
| Density | 7.88 g/cm3 (0.285 lb/in3) |
| Modulus of elasticity | 200 GPa |
| Thermal conductivity | 15 W/m.K |
| Specific heat capacity | 500 J/kg.K |
| Coefficient of linear expansion | 17.2 x 10-6 /K |
| Magnetic response | Non-magnetic, retained after severe cold work |
Specifications and equivalent designations
| Category | Specification |
|---|---|
| Aerospace | AMS 5764, bar, forgings and rings |
| Forgings and fittings | ASTM A182 FXM-19, ASTM A403 |
| Bar and shapes | ASTM A276, ASTM A479, ASTM A314 |
| Plate, sheet and strip | ASTM A240 / ASME SA240 |
| Pipe and tube | ASTM A312, ASTM A412 / ASME SA412 |
| Fasteners | ASTM A193 Grade B8R, ASTM A194 Grade B8, ASTM F1314 |
| Welding consumable | AWS A5.9 ER209, Nitronic 50W (E/ER209) |
| Sour service | NACE MR0175 / ISO 15156-3, NACE MR0103 |
| European near-equivalents | SEW 390 grades 1.3964 (X2CrNiMnMoNNb21-16-5-3) and 1.3974 (X2CrNiMnMoNNb23-17-6-3) |
| Cast counterpart | CG6MMN, UNS J93790 |
The SEW 390 grades are near-equivalents rather than drop-in substitutes. Both 1.3964 and 1.3974 run higher nickel and tighter carbon than XM-19, so clear any substitution with your design authority first.
Forging, heat treatment and machining
Forging
Forge between 1177 C and 1204 C (2150-2200 F). XM-19 needs more press power than the standard austenitic grades, so die design, bite sequence and reheat planning all matter. Our presses and ring mill are set up for the higher flow stress.
Solution annealing
Anneal at 1066-1121 C (1950-2050 F) and water quench. Use 1066 C for most service, since it gives the higher mechanical properties together with full corrosion resistance. Use 1121 C when as-welded material will see strongly corrosive media, to limit intergranular attack. The grade cannot be hardened thermally.
Machining
The work-hardening rate is high. Run lower cutting speeds than for standard austenitics, keep the set-up rigid, use positive feeds heavy enough to cut under the hardened skin, and allow enough spindle power. Coated carbide tooling is the usual choice. Factor this into the machining allowance you ask us to leave.
Welding
Weldable by the usual processes, with Nitronic 50W (AWS E/ER209) as the recommended filler. Autogenous high energy density processes such as electron beam and laser welding need care because of the low ferrite number and the risk of severe outgassing from the nitrogen.
XM-19 forgings we make
Everything is made to customer drawing or specification. Usual forms are seamless rolled rings, forged rings, flanges, round bars, shafts and eccentric shafts, discs and hubs, sleeves, bushings, tube sheets, forged tubes and pipes, nozzles, valve bodies, stems and seat rings, gears, spindles, blocks and crankshafts.
| Stage | Detail |
|---|---|
| Melting | EAF plus VOD, ESR remelt available for improved cleanliness and segregation control |
| Forming | Open-die forging and seamless ring rolling at 1177-1204 C |
| Heat treatment | Solution anneal 1066-1121 C and water quench, with furnace charts recorded |
| Ultrasonic testing | EN 10228-3, SEP 1921 or ASTM A388 as specified; PT and MT on request |
| Mechanical testing | Tensile, impact including sub-zero, hardness; intergranular corrosion testing on request |
| Certification | EN 10204 3.1 mill certificate, or 3.2 with third-party inspection such as TUV, BV, SGS or Lloyd's |
| Size range | Quoted per enquiry. Please give O.D., I.D., height or length, and finished weight |
Where XM-19 forgings are used
Oil, gas and offshore
Down-hole and oilfield production equipment, subsea and deepwater production systems, wellhead and Christmas tree parts, forged valve bodies, stems, seat rings and blocks. Service experience shows good resistance to sulfide stress cracking, and the grade is listed in NACE MR0175 / ISO 15156-3 to 35 HRC.
Marine and shipbuilding
Seawater pump shafts and casings, gate valves for tanker seawater ballast systems, marine hardware, deep-sea sampler and incubation chambers, underwater robotic arms, deck machinery forgings.
Chemical and fertiliser
Urea plant equipment, ammonium carbamate pumps, pressure vessels, tanks, heat exchanger tube sheets, piping, fittings, flanges, valve and pump components.
Nuclear and waste handling
Waste calcination systems, aqueous fluoride handling systems, waste canisters, plus forged rings, shafts, flanges and piping for nuclear service.
Power and rotating equipment
Turbine and gas compressor parts, gearbox gears and spindles, power transmission shafts, industrial air compressors, generators and nitrogen generators.
Pulp, paper, food and pharmaceutical
Forged rolls, wheels, manifolds and crystalliser equipment for pulp and paper, food processing, pharmaceutical and biochemical plant, textile machinery and photographic equipment.
Common questions about XM-19
Is XM-19 the same as Nitronic 50?
Yes. XM-19 is the ASTM designation, UNS S20910 is the UNS number and Nitronic 50 is a trade name for the same nitrogen-strengthened austenitic stainless steel. Nitronic is a registered trademark of its owner and appears here only to identify the alloy.
How much stronger is XM-19 than 316 or 316L?
Annealed XM-19 has a minimum 0.2 per cent yield strength of 380 MPa (55 ksi), roughly double that of 316L at room temperature, and a minimum tensile strength of 690 MPa (100 ksi). Corrosion resistance is equal to or better than 316, 316L, 317 and 317L thanks to the higher chromium and the nitrogen. That combination is the usual reason engineers move from 316L to XM-19 on pump shafting and valve internals.
Does XM-19 become magnetic after cold working?
No. It stays essentially non-magnetic even after severe cold work, which is why it gets specified where low magnetic permeability is part of the design requirement.
Can XM-19 be used in sour service?
XM-19 in the annealed and in the high-strength hot-rolled condition is included in NACE MR0175 / ISO 15156-3 for sulfide stress cracking resistance at hardness up to 35 HRC maximum. Check the H2S partial pressure, chloride and temperature limits in the standard against your real service conditions before committing.
Which annealing temperature should I specify?
For most applications specify 1066 C (1950 F), which gives the higher level of mechanical properties with full corrosion resistance. Specify 1121 C (2050 F) when as-welded material will be used in strongly corrosive media, to reduce the chance of intergranular attack. Both are followed by water quench.
Can XM-19 be hardened by heat treatment?
No. It is fully austenitic. Strength above the annealed minimum comes from hot rolling or strain hardening, which raise the minimum yield strength to 415 MPa and 725 MPa respectively.
Why is XM-19 harder to forge and machine?
The nitrogen content and the high work-hardening rate raise flow stress. Forging takes more press power than standard austenitics, and machining takes lower speeds, rigid set-ups, more power and coated carbide tooling. Allow extra time for machined parts when planning delivery.
What certification comes with the forgings?
EN 10204 3.1 mill certificates as standard, EN 10204 3.2 with third-party inspection on request. Ultrasonic testing follows EN 10228-3, SEP 1921 or ASTM A388 according to the specification you nominate.
What do you need in order to quote?
Grade and controlling specification, a drawing or the rough dimensions (O.D., I.D., height or length), delivery condition, quantity, NDT and certification requirements, and the destination port. Email sales@steelforgepieces.com or call +86-189-2135-9659.
Related grades we forge
Ask for a price on XM-19 forgings
Jiangyin Jiangnan Metal Co., Ltd., open-die forging factory, Jiangyin, Jiangsu, China. Send a drawing or the main dimensions and we will come back with price, lead time and the proposed test plan.
Address: No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Phone: +86-189-2135-9659
Email: sales@steelforgepieces.com
Data on this page is taken from published XM-19 / UNS S20910 / Nitronic 50 literature and from the applicable ASTM, AMS and NACE documents. Figures are for guidance. The controlling document for any order is the specification named on the purchase order and the resulting EN 10204 certificate. Nitronic is a registered trademark of its respective owner and is used here only to identify the alloy.
Last technical review: , by the Jiangyin Jiangnan Metal technical sales team.