20Mn6 Forgings
Material No. 1.1169 · DIN 17200 · manganese special steel
20Mn6 (material number 1.1169) is a manganese-alloyed special steel to DIN 17200, with a nominal analysis of 0.17–0.23 % carbon and 1.30–1.60 % manganese. It is specified for high-pressure vessels and pressure-bearing tube in service down to −100 °C, where toughness at low temperature counts for more than hardness. Jiangyin Jiangnan Metal Co., Ltd., an open-die forging factory at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China, forges 20Mn6 to customer drawing as bars, hollow bars, seamless rolled rings, discs, blocks, shafts and flanges.
- Grade
- 20Mn6
- Material number
- 1.1169
- Standard
- DIN 17200
- Steel group
- Non-alloy special steel
- Process
- Open-die forging
- Made in
- Jiangyin, China
Send your drawing Jump to composition Quotations normally go back within 24 hours
20Mn6 at a glance
- Designation: 20Mn6 is the DIN designation. The matching Werkstoff (material) number is 1.1169.
- Chemistry: 0.17–0.23 % C, 0.30–0.60 % Si, 1.30–1.60 % Mn, P and S each 0.035 % maximum, balance Fe.
- Classification: a non-alloy special steel. Manganese is the only significant addition, so there is no chromium, nickel or molybdenum in the analysis.
- Heat treatment: harden in water at 860–890 °C, temper at 500–650 °C. Normalising is 880–910 °C, air cooled.
- Typical use: high-pressure vessels and tube rated for service down to −100 °C.
- Supplied by Jiangyin Jiangnan Metal as: forged round, square, flat and hex bar; hollow bar, sleeves and shells; seamless rolled rings; forged rings; discs, blocks and plates; gear and pinion shafts; spindles; flanges.
- Contact: sales@steelforgepieces.com, +86 189 2135 9659, No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China.
What is 20Mn6 steel?
20Mn6 is a low-carbon steel that gets its properties from manganese rather than from a conventional alloy package. At 1.30–1.60 % Mn it carries roughly three times the manganese of a plain C22 carbon steel. That raises hardenability and tensile strength while the carbon stays low enough for the steel to weld and machine without trouble. DIN files it as a non-alloy special steel: the word "special" refers to the tight limits on phosphorus and sulphur, not to any alloy content.
Pressure equipment is where the grade earns its place. A designer gets a workable strength level and dependable low-temperature toughness without paying for a chromium-molybdenum steel, and the fabricator gets something that behaves predictably under the torch. The limitation is section size. With no molybdenum to slow the transformation, through-hardening drops away quickly as the forging gets heavier, so thick 20Mn6 sections are normally supplied normalised rather than fully quenched and tempered.
20Mn6 chemical composition
| Element | Symbol | Min % | Max % | Role in this grade |
|---|---|---|---|---|
| Carbon | C | 0.17 | 0.23 | Kept low for weldability and low-temperature toughness |
| Silicon | Si | 0.30 | 0.60 | Deoxidiser, plus a little solid-solution strength |
| Manganese | Mn | 1.30 | 1.60 | Principal alloying element for hardenability and strength |
| Phosphorus | P | — | 0.035 | Residual, held down to protect toughness |
| Sulphur | S | — | 0.035 | Residual, held down to protect transverse ductility |
Ladle analysis to DIN 17200. Product analysis taken on a finished forging may deviate within the tolerances of the applicable standard. Each heat is supplied with its own certificate of analysis.
20Mn6 mechanical properties
Properties for 20Mn6 depend on ruling section, delivery condition and test position, so the figures below are given by section band. They are indicative values for enquiry and sizing. The EN 10204 certificate issued with the forging is the governing document.
| Condition | Ruling section | Rp0.2 min. | Rm | A5 min. | KV at −40 °C | Hardness |
|---|---|---|---|---|---|---|
| Normalised | up to 100 mm | 295 MPa | 490–630 MPa | 22 % | 27 J | 140–190 HB |
| Normalised | 100–250 mm | 275 MPa | 470–610 MPa | 21 % | 27 J | 135–185 HB |
| Normalised | 250–400 mm | 255 MPa | 450–590 MPa | 20 % | 27 J | 130–180 HB |
| Quenched and tempered | up to 100 mm | 390 MPa | 590–740 MPa | 20 % | 40 J | 175–220 HB |
| Quenched and tempered | 100–250 mm | 345 MPa | 550–700 MPa | 19 % | 35 J | 165–210 HB |
Impact testing at other temperatures, down to −100 °C, is carried out on request. Transverse testing, through-thickness testing and quarter-radius sampling can all be specified on the order.
20Mn6 heat treatment
| Operation | Temperature | Cooling | Purpose |
|---|---|---|---|
| Normalising | 880–910 °C | Still air | Refine grain after forging. Usual condition for heavy sections |
| Hardening | 860–890 °C | Water quench | Transform to martensite and bainite |
| Tempering | 500–650 °C | Air | Set final strength and restore toughness |
| Soft annealing | 650–700 °C | Furnace cool | Lower hardness ahead of heavy machining |
| Stress relief | 550–650 °C | Furnace cool to 400 °C, then air | Relieve machining and welding stresses |
Water quenching is hard on abrupt section changes. Where a drawing has thin webs next to heavy hubs, or sharp internal corners, we look at the geometry before committing to a hardening route and will often recommend normalised or normalised-and-tempered delivery instead. Tell us the properties you need and the ruling section, and the heat-treatment route comes back with the drawing review.
Forging 20Mn6
20Mn6 forges without difficulty. Billet is soaked to temperature, then upset and drawn under open dies with reheats as needed to keep the finishing temperature above the point where the structure stops recrystallising. Ring geometries are pierced and expanded on a radial-axial mill, which puts the grain flow around the circumference instead of cutting across it.
| Parameter | Value |
|---|---|
| Start forging temperature | 1150–1200 °C |
| Finish forging temperature | not below 850 °C |
| Minimum forging ratio | 3:1, higher on request |
| Post-forge cooling | Still air, or slow cool in an insulated pit for heavy sections |
| Post-forge condition | Normalised as standard, unless the order calls for something else |
What is 20Mn6 equivalent to?
There is no exact one-to-one international equivalent for 20Mn6. The grades below are the closest carbon-manganese steels by chemical analysis, shown with their own ranges so the fit can be judged rather than taken on trust.
| Standard | Grade | Carbon % | Manganese % | How close |
|---|---|---|---|---|
| DIN 17200 (Germany) | 20Mn6 | 0.17–0.23 | 1.30–1.60 | The grade itself |
| Werkstoff-Nr. | 1.1169 | 0.17–0.23 | 1.30–1.60 | Same steel, material-number form |
| AISI / SAE (USA) | 1524 | 0.19–0.25 | 1.35–1.65 | Nearest US carbon-manganese grade |
| AISI / SAE (USA) | 1522 | 0.18–0.24 | 1.10–1.40 | Leaner in manganese |
| GB/T 3077 (China) | 20Mn2 | 0.17–0.24 | 1.40–1.80 | Nearest Chinese grade, richer in manganese |
| DIN (Germany) | 20Mn5 / 1.1133 | 0.17–0.23 | 1.10–1.40 | Leaner neighbour in the same family |
These cross-references compare ladle analysis only. Mechanical acceptance, impact requirements, permitted residuals and pressure-equipment approval all differ between standards. Confirm any substitution with your design authority before ordering. We are glad to review the swap with you.
20Mn6 vs 20Mn5
Both sit in the same low-carbon manganese family, and the number after "Mn" is roughly the manganese content multiplied by four. 20Mn6 carries the higher manganese of the two, which buys more hardenability and a higher strength level in the same section at some cost in weldability. Where a drawing calls for 20Mn5 and only 20Mn6 is available, the substitution usually runs toward higher strength, but the weld procedure and the impact requirement both need checking first.
20Mn6 forged products we make
Everything below is forged to your drawing or specification. We do not hold 20Mn6 as catalogue stock, and minimum order is one piece. Sizes beyond these ranges are often still possible, so send the drawing and we will confirm.
| Product form | Also called | Size range | Single-piece weight |
|---|---|---|---|
| Forged bar | Round bar, square bar, flat and rectangular bar, hex bar | 80–1200 mm diameter or across flats, up to 8000 mm long | 20–20,000 kg |
| Hollow forgings | Hollow bar, sleeve, bush, bushing, cylinder, barrel, casing, shell, hub, housing | 150–2500 mm OD, 50–2000 mm ID | up to 20,000 kg |
| Seamless rolled rings | Radial-axial rolled rings | 200–3000 mm OD, height up to 1000 mm | up to 15,000 kg |
| Forged rings | Mandrel-forged and punched rings | 200–3000 mm OD | up to 20,000 kg |
| Discs, blocks and plates | Forged disc, disk, block, slab | 200–2500 mm diameter, or to drawing | up to 20,000 kg |
| Shafts | Gear shaft, pinion shaft, spindle, stepped shaft | up to 8000 mm long | up to 20,000 kg |
| Forged flanges | Weld-neck, slip-on, blind, custom profile | 100–3000 mm OD | up to 10,000 kg |
How we make a 20Mn6 forging
- Drawing review and quotationWe check forgeability, ruling section, machining allowance and the heat-treatment route before pricing, and flag anything likely to cause trouble at the press.
- Steel making and material certificationMelt sourced to the required analysis, with the mill certificate traceable to heat number.
- Heating and open-die forgingBillet soaked to 1150–1200 °C, then upset and drawn under open dies to break down the cast structure and develop grain flow.
- Ring rollingFor ring geometries, the pierced blank is rolled radially and axially to final proportions.
- Heat treatmentNormalising, or hardening and tempering to the temperatures in Table 3, to whichever condition the specification calls for.
- Testing and inspectionChemical analysis, mechanical testing, hardness, dimensional check, and ultrasonic or magnetic-particle examination where specified.
- MachiningRough or finish machining to drawing, so the part arrives ready for your process rather than your lathe.
- Documentation and despatchCertificates issued against the heat, parts marked, packed and shipped.
Where 20Mn6 is used
The defining application is pressure equipment operating cold. DIN lists 20Mn6 for high-pressure vessels and tube down to −100 °C, and that low-temperature rating is the reason engineers reach for it ahead of a plain carbon steel at similar strength.
- High-pressure vessel shells, heads and nozzle forgings
- Pressure-bearing tube and pipe components for cold and cryogenic service
- Flanges and closures on vessels rated below ambient temperature
- Machine components needing a weldable medium-strength steel in forged form
- Gear and pinion shafts, spindles and hubs in general engineering
Suitability for a particular pressure code, whether PED, ASME or GB 150, depends on the approvals held for the grade and for the manufacturer, not on the analysis alone. Tell us which code you are building to and we will confirm what we can supply against it.
About the factory
Jiangyin Jiangnan Metal Co., Ltd. is an open-die forging factory at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China. We forge carbon steel, alloy steel, tool steel, stainless steel and nickel alloys to customer drawing, and produce seamless rolled rings, forged flanges, bars, discs, shafts and hollow forgings. Jiangyin sits in the Yangtze River Delta within road distance of Shanghai and Ningbo, which is what makes export shipping of heavy single pieces workable.
| Legal name | Jiangyin Jiangnan Metal Co., Ltd. |
|---|---|
| Business | Open-die forging factory |
| Address | No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China |
| Telephone | +86 189 2135 9659 |
| sales@steelforgepieces.com | |
| Website | www.steelforgepieces.com |
| Materials | Carbon steel, alloy steel, tool steel, stainless steel, nickel alloys |
| Certification supplied | Material certificate to EN 10204 3.1 with every order, 3.2 third-party inspection on request |
| Minimum order | One piece |
| Markets served | Worldwide |
20Mn6 questions we get asked
What is the material number for 20Mn6?
1.1169. Same steel, two names: 20Mn6 is the DIN designation, 1.1169 is the Werkstoff number printed on the mill certificate.
Is 20Mn6 an alloy steel or a carbon steel?
DIN classifies 20Mn6 as a non-alloy special steel. Manganese at 1.30 to 1.60 % is the only significant addition and there is no chromium, nickel or molybdenum, so it behaves as an enhanced carbon-manganese steel rather than a true alloy steel. Many suppliers still file it under alloy steel for convenience, this site included.
Can 20Mn6 be welded?
Yes, with normal procedures. Carbon sits at 0.17 to 0.23 %, which is comfortable territory, but the manganese pushes the carbon equivalent up far enough that heavier sections want preheat and a controlled interpass temperature. Work out CEV from the actual heat analysis rather than from the middle of the specification range, because a heat running at 1.58 % Mn behaves differently from one at 1.32 %. On pressure parts post-weld heat treatment is normally called for anyway. Qualify the procedure on the real section thickness, not on a coupon.
What is the minimum order quantity for 20Mn6 forgings?
One piece. Open dies and a ring mill both work from a single billet, so a prototype or a one-off replacement is no problem. Repeat bar sizes get cheaper above roughly 500 kg.
Do you supply 20Mn6 with EN 10204 3.1 or 3.2 certificates?
3.1 as standard with every order. For 3.2 we arrange third-party inspection through SGS, BV, TUV or Lloyd's Register. Flag it at enquiry stage so the witness points go into the schedule.
How long does a 20Mn6 forging take?
Rough-forged and normalised parts usually run 25 to 35 days from order. Parts that need quenching and tempering, machining to drawing, or third-party witnessed testing typically run 35 to 45 days. Very heavy single pieces and jobs waiting on a specific melt take longer, and we give a firm date with the order acknowledgement rather than at quotation.
Do you hold 20Mn6 in stock?
No. Everything is forged to order, so size, forging ratio and heat-treatment condition follow your drawing rather than the rack.
What information do you need to quote a 20Mn6 forging?
A drawing or dimensioned sketch, the quantity, the delivery condition (as-forged, normalised, or quenched and tempered), the machining allowance if the part is rough-forged, the certificate type you need, and the standard or pressure code the part is built to. With those six things we can quote without going back and forth.
Other grades we forge
If 20Mn6 is not the right fit, these are the grades buyers most often compare it against:
- 42CrMo4 (1.7225) forgings, the standard chromium-molybdenum step up when 20Mn6 cannot reach the strength or the section size required.
- AISI 4140 forgings, the American counterpart to 42CrMo4, for drawings written to ASTM or SAE.
- AISI 4130 forgings, a leaner chromium-molybdenum grade with better weldability than 4140.
- 34CrMo4 (1.7220) forgings, the European equivalent of 4130 and common on pressure-part drawings.
- AISI 8630 forgings, a nickel-chromium-molybdenum grade widely specified for wellhead and subsea components.
- 34CrNiMo6 (1.6582) forgings, for cases where deep hardening through a heavy section is the constraint.
- 18CrNiMo7-6 forgings, a case-hardening grade for gear blanks and pinion shafts.
- Carbon steel forgings, if 20Mn6 is more steel than the part actually needs.
Send us your 20Mn6 drawing
Email the drawing with quantity, delivery condition and certificate requirement, and a price and lead time come back to you. If the geometry is awkward to forge, we will say so and suggest an alternative rather than quote something that causes trouble later.
- Jiangyin Jiangnan Metal Co., Ltd.
- No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
- Telephone, WhatsApp and WeChat
- +86 189 2135 9659