ASTM Type XM-13 · UNS S13800 · EN 1.4534
XM-13 Forgings The ASTM type designation for UNS S13800, and which specification to put on the order
XM-13 is a type designation inside the ASTM age-hardening stainless specifications, not an alloy name in its own right. It points at UNS S13800, the 13 chromium, 8 nickel, molybdenum and aluminium precipitation-hardening stainless steel also sold under the PH 13-8 Mo trademark. This page explains the designation and the specification to cite for each product form. The full property datasheet sits on the PH13-8Mo page.
- Designation
- Type XM-13
- UNS
- S13800
- Forgings
- ASTM A705 Type XM-13
- Bars
- ASTM A564 Type XM-13
- Plate
- ASTM A693 Grade XM-13
- Aerospace
- AMS 5629 bars and forgings
- Europe
- EN 1.4534, X3CrNiMoAl13-8-2
- Conditions
- A, RH950, H950 to H1150M
- Max piece
- 30,000 kg; rings to 6,000 mm OD
- Lead time
- 20 to 60 days
What the designation means
XM-13 is one of the type numbers ASTM uses for age-hardening stainless steels that have no AISI three-digit number. It identifies UNS S13800: 12.25 to 13.25 percent chromium, 7.50 to 8.50 percent nickel, 2.00 to 2.50 percent molybdenum and 0.90 to 1.35 percent aluminium, carbon 0.05 percent maximum. The same chemistry carries the PH 13-8 Mo trademark and the European number 1.4534.
The XM series exists because ASTM needed designations for proprietary and later-developed grades that the AISI numbering system never covered. A type number is therefore a slot in a specification rather than a standalone standard: XM-13 only has meaning once you name the specification it sits in, because the same type number appears in A564 for bars, A705 for forgings and A693 for flat products, each with its own testing, tolerance and acceptance rules.
That is the practical point for anyone writing a purchase order. Naming XM-13 on its own tells the mill the chemistry but not the product standard, the required condition or the test regime. Naming ASTM A705 Type XM-13, H1050, EN 10204 3.1 tells the mill everything it needs.
The alloy itself hardens by nickel-aluminium intermetallic precipitates rather than carbides, which is why carbon sits at 0.05 percent maximum. Strength is set by one four-hour aging treatment after solution treatment, and the specified minimum tensile strength runs from 1,517 MPa in H950 down to 931 MPa in H1150. Because the carbon, manganese, silicon and sulfur limits are tight and the steel is vacuum melted, transverse and short-transverse ductility stay close to the longitudinal values in heavy sections, which is the reason it appears on landing-gear and thick valve-part drawings rather than 17-4PH.
Which specification to cite
ASTM A705 Type XM-13 for a forging order. ASTM A564 Type XM-13 for bars and shapes, ASTM A693 Grade XM-13 for plate, sheet and strip, AMS 5629 for aerospace bars, forgings, rings and extrusions, EN 1.4534 for European projects. ASTM B564 does not apply to this grade.
| Origin | Designation | Scope |
|---|---|---|
| ASTM, forgings | ASTM A705 Type XM-13 | Age-hardening stainless steel forgings. The specification to cite on a forging order. |
| ASTM, bars | ASTM A564 Type XM-13 | Hot-rolled and cold-finished age-hardening bars, rods and shapes |
| ASTM, flat | ASTM A693 Grade XM-13 | Precipitation-hardening plate, sheet and strip |
| ASTM, listing | ASTM A959 | The practice that assigns and lists the XM type designations |
| UNS | UNS S13800 | Unified Numbering System designation, the neutral reference |
| SAE, bars and forgings | AMS 5629 | Bars, wire, forgings, rings and extrusions. The usual aerospace specification for forged material. |
| SAE, flat | AMS 5864 | Sheet, strip and plate, and the source of the minimum property table below |
| Trademark | PH 13-8 Mo | Registered trademark of Cleveland-Cliffs Inc., formerly AK Steel and Armco. We do not sell under this name and supply the generic equivalents above. |
| Europe | EN 1.4534, X3CrNiMoAl13-8-2 | European material number and name for the same chemistry |
| Shop-floor names | 13-8Mo, 13-8 PH, 13/8 Mo, XM13 | Informal names on legacy drawings, all meaning UNS S13800 |
| Does not apply | ASTM B564 | A nickel-alloy forging specification, frequently cited against this grade in error |
Compiled from ASTM A564, A705, A693 and A959; SAE AMS 5629 and AMS 5864; EN 10088-3 for 1.4534; and mill listings from Rolled Alloys and Universal Stainless, both of which index XM-13 against UNS S13800.
Two errors to watch for on XM-13 drawings and supplier pages. The first is ASTM B564, which covers nickel-alloy forgings such as UNS N04400 and N06600 and has nothing to do with S13800. The correct forging specification is ASTM A705 Type XM-13, or AMS 5629.
The second is the condition H900. This grade is aged at 950, 1000, 1025, 1050, 1100 or 1150 degrees Fahrenheit, plus the refrigerated RH950 cycle and the double-aged H1150M cycle. H900, H925 and H1075 belong to 17-4PH. Where a drawing calls for XM-13 H900, the figures quoted almost always match H950, but the condition has to be confirmed with the designer before the heat is released. An earlier version of this page carried both errors and they were corrected in October 2026.
Chemical composition
Chromium 12.25 to 13.25, nickel 7.50 to 8.50, molybdenum 2.00 to 2.50, aluminium 0.90 to 1.35, carbon 0.05 maximum, silicon 0.10 maximum, phosphorus 0.01 maximum, sulfur 0.008 maximum, nitrogen 0.01 maximum, balance iron, all weight percent.
| Element | Minimum | Maximum | Why the limit sits there |
|---|---|---|---|
| Carbon | – | 0.05 | Strengthening comes from intermetallic precipitates, not carbides, so carbon is a residual |
| Manganese | – | 0.10 | One tenth of the 17-4PH limit, to suppress manganese sulfide inclusions. See the note below. |
| Silicon | – | 0.10 | Held low for cleanliness and transverse ductility |
| Phosphorus | – | 0.010 | Residual, embrittles grain boundaries |
| Sulfur | – | 0.008 | The tightest limit among the common precipitation-hardening grades |
| Nitrogen | – | 0.010 | Controlled, so reducing furnace atmospheres have to be avoided during heat treatment |
| Chromium | 12.25 | 13.25 | Corrosion resistance and martensite stability |
| Nickel | 7.50 | 8.50 | Toughness, and partner to aluminium in the strengthening phase |
| Molybdenum | 2.00 | 2.50 | Pitting resistance and solid-solution strengthening. The 17-4PH and 15-5PH grades have none. |
| Aluminium | 0.90 | 1.35 | The hardening element, forming nanoscale nickel-aluminium precipitates on aging |
| Iron | Balance, about 76 percent | Matrix | |
Rolled Alloys Data Sheet 13-8 Stainless, Bulletin 1022USe, and High Temp Metals PH 13-8 Mo technical data agree on all limits shown. Published comparisons of the specification families list manganese at 0.20 maximum for ASTM and AMS against 0.10 maximum for EN 1.4534, and aluminium at 0.90 to 1.20 for 1.4534 against 0.90 to 1.35 elsewhere. Confirm manganese and aluminium against the edition named on the purchase order; we can melt to either window.
None of this table is reachable by air melting. Carbon at 0.05 percent with silicon at 0.10 percent and sulfur at 0.008 percent needs vacuum induction melting followed by vacuum arc remelting, which is why most forging shops buy S13800 billet rather than make it. We run a 3 t vacuum induction furnace, a 6 t vacuum arc remelting furnace and 3 t and 6 t protective-atmosphere electroslag furnaces on the same site as the presses, so the chemistry on the certificate is our own heat.
Conditions and properties
Solution treat at 927 degrees Celsius and cool below 16 degrees Celsius for Condition A, then age four hours and air cool. Specified minima run 1,517 MPa tensile and 1,414 MPa yield in H950 at 45 HRC, down to 931 and 621 MPa in H1150 at 30 HRC.
| Property | H950 | H1000 | H1025 | H1050 | H1100 | H1150 |
|---|---|---|---|---|---|---|
| Aging temperature, °C | 510 | 538 | 552 | 566 | 593 | 621 |
| Yield 0.2 percent, MPa | 1414 | 1310 | 1207 | 1138 | 931 | 621 |
| Yield 0.2 percent, ksi | 205 | 190 | 175 | 165 | 135 | 90 |
| Tensile, MPa | 1517 | 1414 | 1276 | 1207 | 1034 | 931 |
| Tensile, ksi | 220 | 205 | 185 | 175 | 150 | 135 |
| Elongation in 50 mm, percent | 10 | 10 | 11 | 12 | 14 | 14 |
| Reduction of area, longitudinal, percent | 45 | 50 | 50 | 50 | 50 | 50 |
| Reduction of area, short transverse, percent | 35 | 40 | 45 | 45 | 50 | 50 |
| Hardness, minimum | 45 HRC | 43 HRC | – | 40 HRC | 34 HRC | 30 HRC |
Rolled Alloys Data Sheet 13-8 Stainless, Bulletin 1022USe, tabulating minimum mechanical properties to AMS 5864. Metric values converted at 1 ksi equals 6.895 MPa and rounded. Typical values, the RH950 and H1150M conditions, torsional data and physical properties are on the PH13-8Mo page. Confirm against the edition of AMS 5629, ASTM A705 or AMS 5864 named on the purchase order before releasing a design.
Two conditions sit outside the table. RH950 cools Condition A material to minus 73 degrees Celsius for at least two hours within 24 hours of solution treatment, then ages at 510 degrees Celsius; the cold hold clears retained austenite and gives the highest strength available, around 1,620 MPa typical. H1150M is a two-stage cycle at 760 then 621 degrees Celsius, giving the highest impact energy and the best machinability of the aged conditions.
H1150 and H1150M are terminal. Material bought in either one for easier machining has to be re-solution treated at 927 degrees Celsius before it can be aged again. Hardness alone will not separate H1150 from Condition A, because the two ranges overlap, so the certificate is the evidence rather than a hardness tester on the goods-in bench.
Forged shapes and sizes
Open-die forging for shafts, blocks, discs and tube sheets; seamless ring rolling from 50 to 6,000 mm outside diameter; upset-and-punch forging for short, large-section discs and hubs below the ring-mill range. Single pieces to 30,000 kg.
Rings
Seamless rolled rings and forged rings, including gear ring blanks, retaining rings and valve seat rings. Forged rings and rolled rings.
Shafts
Pump and plunger-pump shafts, spindles, eccentric shafts, pins and stepped shafts to 14,000 mm turned length. Forged shafts.
Valve and wellhead
Stems, seat rings, bodies, bonnets, blocks and nozzles for ball, gate, globe, check and plug valves. Forged valve parts.
Discs and tube sheets
Solid forged discs, blanks, covers and tube sheets to 5,000 mm machined diameter, supplied proof-machined for volumetric inspection. Tube sheets.
Flanges and bars
Weld neck, blind, slip-on and special flanges, plus round and flat bars and blocks as machining stock. Flanges, bars.
Hollow sections
Bushings, sleeves, couplings and hollow cylinders bored from solid forged blanks, to 1,600 by 10,000 mm on the deep-hole drill.
For XM-13 the clean-melt ingot governs the maximum size rather than the press. The 3 t vacuum induction furnace and the 6 t vacuum arc remelting furnace set the realistic ceiling for double-melt material, so confirm the melt route with the enquiry and we will confirm the achievable size against it.
Hot working
Heat uniformly to 1177 to 1204 degrees Celsius and soak one hour at temperature before forging. Do not forge below 954 degrees Celsius. Air cool to about 16 degrees Celsius after forging. Forgings must be solution treated before aging; hot-worked material that skips the solution treatment will not harden properly. Cold saw bars and billets rather than using an abrasive wheel, which can start small surface cracks in annealed stock.
High Temp Metals PH 13-8 Mo technical data, workability section.
Machining
In Condition A the alloy gives good tool life and finish, but at surface speeds 20 to 30 percent below 17-4PH and 20 to 30 percent below Types 302 and 304. Machinability in the aged conditions improves as the aging temperature rises, with H1150M the easiest of them. In the high-strength conditions at 45 HRC and above, turning, drilling and threading are demanding, so rough in Condition A or H1150M and finish after aging. Aging produces a small contraction that increases with aging temperature, which is the other reason to leave tight-tolerance features until last.
XM-13 against the other PH grades
| Grade | UNS | Peak condition | Tensile minimum | Distinguishing feature |
|---|---|---|---|---|
| XM-13 | S13800 | H950 | 1517 MPa | Highest strength of the group, molybdenum and aluminium additions, vacuum melted, short-transverse reduction of area specified separately |
| 17-4PH | S17400 | H900 | 1310 MPa | The general industrial grade, lowest cost and widest availability, with H1150-M used for sour service |
| 15-5PH | S15500 | – | – | A lower-ferrite variant of 17-4PH developed for better transverse toughness in heavy forgings. Figures are on the 15-5PH page. |
| 17-7PH | S17700 | – | – | Semi-austenitic, formed annealed then transformation hardened. Mainly a sheet, strip and spring grade. |
XM-13 minimum from Rolled Alloys tabulating AMS 5864. 17-4PH minimum as published on our own 17-4PH page from ASTM A564 and A705. The 15-5PH and 17-7PH cells are left blank rather than estimated; see those pages for verified figures.
The selection logic in practice: start with 17-4PH and move to XM-13 when one of three things is true. The section is heavy and the drawing calls out transverse or short-transverse properties. The required strength is above what H900 on 17-4PH will give. Or the specification itself names AMS 5629, UNS S13800 or Type XM-13. The grade costs more and machines harder, and it earns that in those three cases and not many others.
It is also the wrong answer above roughly 593 degrees Celsius, and long holds between about 288 and 482 degrees Celsius can reduce toughness. Where strength at temperature rather than at ambient is the requirement, A286 is the usual move.
Testing and certification
Ultrasonic testing to ASTM A388 or EN 10228-3, the part covering ferritic and martensitic steel forgings, with magnetic particle testing to ASTM E709 and liquid penetrant where specified. Chemistry by optical emission spectrometry to ASTM E415 with positive material identification, tensile testing to ASTM A370 and ISO 6892, Charpy V-notch to minus 60 degrees Celsius, grain size to ASTM E112.
EN 10204 3.1 mill certificates are standard and EN 10204 3.2 witnessed by BV, DNV, LR, SGS, TUV or your own inspector is available on request. The works holds CCS, BV, DNV, LR and NK approvals. Because the steel is melted here, the certificate traces the part to its own heat number rather than stopping at a purchased billet. Tests outside our in-house scope are placed with an accredited third-party laboratory and reported with the mill certificate; state the requirement at enquiry stage so it can be scheduled before shipment.
Sour service. NACE MR0175 and ISO 15156-3 list precipitation-hardening stainless steels with named heat-treatment conditions, hardness ceilings and limits on hydrogen sulfide partial pressure, chloride concentration, pH and temperature. Acceptance is tied to the condition and the environment, not to the grade, and the editions change. Send the hydrogen sulfide partial pressure, chloride level, pH and maximum temperature with the enquiry so the requirement can be reviewed before the order is accepted.
How to order
Quotations are prepared from a drawing or a written specification. Sending the six items below in the first message removes a round trip and normally gets a price back within two working days. Minimum order is 10 kg with no minimum piece count. Normal lead time is 20 to 60 days, with XM-13 at the upper end because of the remelting step.
- Specification. ASTM A705 Type XM-13 for forgings, ASTM A564 Type XM-13 for bars, AMS 5629 for aerospace, or EN 1.4534. Not ASTM B564.
- Melt route. Single melt, vacuum induction melting plus vacuum arc remelting, or electroslag remelted. Double melt is normal for this grade and affects price and lead time.
- Dimensions or drawing. For example 620 mm outside by 420 mm inside by 180 mm high, or a drawing or model as PDF, DWG, DXF or STEP with tolerances, surface roughness and any grain-flow requirement.
- Delivery condition. Condition A for onward fabrication, H1150M where machining governs, or the final aged condition from RH950, H950, H1000, H1025, H1050, H1100 or H1150.
- Heat treatment and testing. For example solution 927 degrees Celsius then age H1050, ultrasonic to EN 10228-3, transverse Charpy at a stated temperature.
- Certification and destination. EN 10204 3.1 or 3.2 with the witnessing body if 3.2, any NACE review required, quantity, required date and destination port.
Send an XM-13 drawing or specification
We melt, forge, heat-treat, machine and test UNS S13800 on one site in Jiangyin, Jiangsu. Customer audits and third-party inspection visits are welcome.
sales@steelforgepieces.com | 0086-189-2135-9659 | WhatsApp
No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province 214423, China
Wuxi Shuofang airport 30 km, Shanghai airports 160 km
Questions
What is XM-13 stainless steel?
XM-13 is an ASTM type designation, not an alloy name of its own. It identifies UNS S13800, a martensitic precipitation-hardening stainless steel of roughly 12.7 percent chromium, 8 percent nickel, 2.2 percent molybdenum and 1 percent aluminium, with carbon at 0.05 percent maximum. The same chemistry is sold under the trademark PH 13-8 Mo and is listed in Europe as EN 1.4534. It hardens by nickel-aluminium intermetallic precipitates in a single four-hour aging treatment.
Is XM-13 the same as PH13-8Mo?
Yes, the same chemistry under two naming systems. XM-13 is the ASTM type designation used in A564, A705 and A693. PH 13-8 Mo is a registered trademark of Cleveland-Cliffs Inc. UNS S13800 is the neutral number both point to. An order can be placed under any of them and certified against the designation named on the purchase order. Full property data is on our PH13-8Mo page.
Which ASTM standard covers XM-13 forgings?
ASTM A705 Type XM-13, Age-Hardening Stainless Steel Forgings. ASTM A564 Type XM-13 covers hot-rolled and cold-finished bars and shapes, ASTM A693 Grade XM-13 covers plate, sheet and strip, and SAE AMS 5629 covers bars, wire, forgings, rings and extrusions for aerospace work. ASTM B564 is cited for this grade on a number of supplier pages, including an earlier version of this one, but it covers nickel-alloy forgings and does not apply.
Does XM-13 have an H900 condition?
No. The conditions are A, RH950, H950, H1000, H1025, H1050, H1100, H1150 and H1150M. H900, H925 and H1075 belong to 17-4PH. Where a drawing calls for XM-13 H900, the properties quoted alongside it almost always match H950, which has a specified minimum tensile strength of 1,517 MPa at 45 HRC, but the condition should be confirmed with the designer before the heat is released.
What is the strongest condition available?
Among the single-step aged conditions, H950, with a specified minimum tensile strength of 1,517 MPa and minimum yield of 1,414 MPa at 45 HRC minimum. RH950, which adds a hold at minus 73 degrees Celsius before aging at 510 degrees Celsius to clear retained austenite, reaches about 1,620 MPa tensile as a typical value and around 48 HRC.
How large a forging can you make in this grade?
Plant limits are 30,000 kg single-piece weight on the 6,300 t, 4,000 t and 2,000 t presses, and seamless rolled rings to 6,000 mm outside diameter on the 6 m mill, with 3 m and 1 m mills and an upset-and-punch route from 50 mm. For XM-13 the clean-melt ingot governs rather than the press: the 3 t vacuum induction and 6 t vacuum arc remelting furnaces set the ceiling for double-melt material. Confirm the melt route with the enquiry and we will confirm the achievable size.
Why does my drawing say 1.4534 instead of XM-13?
1.4534 and X3CrNiMoAl13-8-2 are the European material number and name for the same chemistry. European projects, CE-marked equipment and European offshore work normally specify it that way. The order can be certified to the designation on the purchase order with the equivalents listed on the same certificate.
Sources
Property data here is taken from the published sources below and cross-checked against our own production test records. Values should be confirmed against the edition of the specification named on the purchase order before a design is released.
Rolled Alloys, Data Sheet 13-8 Stainless, Bulletin 1022USe, for chemistry, physical properties, heat-treating parameters and the minimum mechanical properties to AMS 5864. High Temp Metals, PH 13-8 Mo technical data, for cycle definitions, corrosion behaviour, workability and machining parameters. ASTM A564 and A564M Type XM-13, ASTM A705 and A705M Type XM-13, ASTM A693 Grade XM-13 and ASTM A959 for the designation itself. SAE AMS 5629 and AMS 5864. EN 10088-3 for 1.4534 and X3CrNiMoAl13-8-2. ASTM A388 and EN 10228-3 for ultrasonic testing, EN 10204 for certificate types. Universal Stainless grade listing for the industry name index linking XM-13, PH13-8, 13-8Mo, AISI 632, DIN 1.4534 and UNS S13800. Jiangyin Jiangnan Metal Co., Ltd. equipment register, laboratory register and production records for all capability, size, lead-time and certification statements.
Citation: Jiangyin Jiangnan Metal Co., Ltd., XM-13 Forgings, ASTM A705 Type XM-13, UNS S13800, EN 1.4534, steelforgepieces.com, revised 11 October 2026, https://www.steelforgepieces.com/Stainless-Steel/XM-13.html