XM-12 Forgings — UNS S15500 / 15-5 PH Stainless Steel
Open-die forged rings, flanges, shafts, discs and bars to ASTM A705 / ASME SA-705 · Page reviewed
XM-12 is the ASTM type designation for UNS S15500, the martensitic precipitation-hardening stainless steel sold commercially as 15-5 PH and listed as 1.4545 in the European Werkstoff system. It carries roughly 15 percent chromium, 5 percent nickel and 4 percent copper, and was developed from 17-4 PH with less delta ferrite in order to improve transverse toughness in heavy sections. Forgings are supplied solution annealed in Condition A, or aged to H900 through H1150M for tensile strengths from 795 to 1310 MPa.
- Common names
- XM-12, 15-5 PH, 15/5 PH
- UNS number
- S15500
- Werkstoff number
- 1.4545
- Alloy class
- Martensitic precipitation-hardening (age-hardening) stainless steel
- Forging standard
- ASTM A705 / A705M, adopted as ASME SA-705. Bars and shapes are covered by ASTM A564 / A564M instead.
- Other specifications
- AMS 5659, AMS 5862, ASTM A693, ASTM A698
- Conditions supplied
- A, H900, H925, H1025, H1075, H1100, H1150, H1150M
- Strength range
- 795 to 1310 MPa tensile (115 to 190 ksi), set by ageing temperature
- Corrosion resistance
- Moderate, broadly similar to Type 304, service to about 315 °C
- Ring size range
- OD 50 mm to OD 6,000 mm on the radial-axial mills
- Maximum single piece
- 30 tonnes, from a 60 t heat on the 6,300 t press
- Minimum order
- 10 kg, no minimum piece count
- Lead time
- 20 to 60 days
- Manufacturer
- Jiangyin Jiangnan Metal Co., Ltd., No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Chemical composition
The limits below are the requirements of ASTM A705 / A705M for Type XM-12. Every heat is melted in our own furnaces and shipped with a certificate to EN 10204 3.1, or 3.2 countersigned by a third party when the order calls for it.
| Grade | C | Mn | P | S | Si | Cr | Ni | Cu | Cb+Ta | Fe |
|---|---|---|---|---|---|---|---|---|---|---|
| XM-12 | 0.07 max | 1.00 max | 0.040 max | 0.030 max | 1.00 max | 14.00–15.50 | 3.50–5.50 | 2.50–4.50 | 0.15–0.45 | Balance |
Molybdenum is not a specified element for XM-12. Where a buyer needs a residual cap on Mo, or tighter phosphorus and sulphur than A705 allows, we set it on the electrode at the melt stage. Aerospace orders written to AMS 5659 carry tighter limits than A705, so state the governing specification and its revision on the enquiry.
Melting route
Steel for XM-12 forgings is melted on site rather than bought in as billet. The standard route is electric arc furnace, ladle furnace, then vacuum oxygen decarburisation, with a maximum heat size of 60 tonnes. For pressure-boundary, subsea and aerospace work we use consumable-electrode remelted stock from the protective-atmosphere electroslag furnaces or the vacuum arc remelting furnace. That matters for more than cleanliness: ASTM A705 ties the thicker section sizes in its mechanical property table to consumable-electrode remelted material, so the melt route decides what section you can actually certify. It also decides price, so tell us at enquiry stage which one you need.
Mechanical properties after ageing
Values are the minimum requirements of ASTM A705 / A705M for Type XM-12, taken longitudinal (L) and transverse (T) to grain flow.
| Condition | Ageing treatment | Tensile, MPa (ksi) | 0.2% yield, MPa (ksi) | Elongation % | Reduction of area % | HB min | HRC min | ||
|---|---|---|---|---|---|---|---|---|---|
| L | T | L | T | ||||||
| H900 | 480 °C, 1 h, air cool | 1310 (190) | 1170 (170) | 10 | 6 | 35 | 15 | 388 | 40 |
| H925 | 495 °C, 4 h, air cool | 1170 (170) | 1070 (155) | 10 | 7 | 38 | 20 | 375 | 38 |
| H1025 | 550 °C, 4 h, air cool | 1070 (155) | 1000 (145) | 12 | 8 | 45 | 27 | 331 | 35 |
| H1075 | 580 °C, 4 h, air cool | 1000 (145) | 860 (125) | 13 | 9 | 45 | 28 | 311 | 32 |
| H1100 | 595 °C, 4 h, air cool | 965 (140) | 795 (115) | 14 | 10 | 45 | 29 | 302 | 31 |
| H1150 | 620 °C, 4 h, air cool | 930 (135) | 725 (105) | 16 | 11 | 50 | 30 | 277 | 28 |
| H1150M | 760 °C 2 h, air cool, then 620 °C 4 h, air cool | 795 (115) | 515 (75) | 18 | 14 | 55 | 35 | 255 | 24 |
A705 states hardness for the aged conditions as a minimum, not a band. If your drawing calls out a range such as 302 to 352 HB, agree it with us as a supplementary requirement before the furnace cycle is fixed, because it changes how we set the soak. Charpy V-notch minima are also specified transversely for most XM-12 conditions and we test to them on request.
Condition A, solution annealed
Condition A is 1040 ± 15 °C, cooled to below 32 °C. A705 caps hardness at 363 HB in this condition and sets no tensile requirement. Most buyers take rough forgings in Condition A, rough machine them, then age. Dimensional change during ageing is small and repeatable, which is why this sequence is normal practice rather than machining fully hard.
Physical properties
| Property | Metric | Imperial |
|---|---|---|
| Density | 7.80 g/cm³ | 0.282 lb/in³ |
| Melting range | 1404 to 1440 °C | 2560 to 2625 °F |
| Modulus of elasticity at 20 °C | 196 GPa | 28.5 x 10&sup6; psi |
| Poisson ratio | 0.272 | 0.272 |
| Thermal expansion, 20 to 100 °C | 11.3 µm/m·°C | 6.3 µin/in·°F |
| Thermal conductivity at 100 °C | 18.3 W/m·K | 10.6 BTU/hr·ft·°F |
Machining and service notes
Machinability sits close to the hardenable 400 series grades such as 410 and 420. It is clearly worse than free-machining 303 or 430F, and nobody should quote XM-12 cycle times from an austenitic benchmark. Take the heavy metal off in Condition A, where hardness is capped at 363 HB, and leave finishing passes for the aged part. At H900 the forging is at least 388 HB and turning, drilling and tapping get slow. Rigid setups, positive rake carbide and plenty of coolant are the difference between a part and a scrapped tool. H1025 and above behave much better.
Ageing temperature also controls stress-corrosion behaviour, and the trade runs the opposite way to strength. H900 gives the highest strength with the lowest toughness and the greatest sensitivity to chloride stress-corrosion cracking. For chloride-bearing or sour service, H1025 and above are the usual choice, and H1150M where toughness governs the design.
XM-12 forged products
Everything listed here is forged from a single piece of steel melted in our own furnaces. No welding, no casting, no purchased billet of unknown origin. We work to the customer drawing or dimension list and do not hold a fixed catalogue.
Regular XM-12 items include seamless rolled rings and contoured rolled rings; weld neck, blind, slip-on and orifice flanges; stepped shafts, eccentric shafts, spindles and pinion shafts; discs, tube sheets and vessel covers supplied proof machined for volumetric inspection; hollow bars, sleeves, bushings and bored cylinders; valve bodies, bonnets, stems, seat rings and blocks; and gear ring blanks.
Where XM-12 forgings are used
Chemical and plunger pump shafts and rings. Pressure vessels, air receivers, and the tube sheets and flanges of shell-and-tube heat exchangers. Columns, towers, tanks, silos, preheaters and process modules. Subsea and deepwater production hardware, wellheads and Christmas trees, industrial air compressors and nitrogen generators. Internals for ball, check, globe, gate and plug valves. Turbine, gas compressor and gearbox power transmission parts. Cement, sugar and concrete mill components. Shipbuilding, pulp and paper, and pharmaceutical equipment.
Inspection, testing and certification
Ultrasonic examination is carried out to EN 10228-3, SEP 1921, ASTM A388 or whatever class your order nominates. Mechanical testing follows ASTM A370 as A705 requires, using prolongations or sacrificial test forgings according to the tonnage rules in the standard. We also offer positive material identification, liquid penetrant examination, hardness surveys, grain size and intergranular corrosion testing, and dimensional reports. The works holds CCS, BV, DNV, LR and NK approvals, and certificates are issued to EN 10204 3.1 or 3.2.
Common questions about XM-12
Is XM-12 the same thing as 15-5 PH?
Yes. XM-12 is the type designation ASTM uses in A705 and A564 for the alloy numbered S15500 in the UNS system, sold commercially as 15-5 PH and as 1.4545 in Europe. One material, four names.
How does XM-12 differ from 17-4 PH?
15-5 PH was developed from 17-4 PH (Type 630, UNS S17400) with a leaner chromium range and slightly more nickel, which cuts the amount of delta ferrite in the microstructure. The practical result is better toughness and better transverse properties, and that gap widens as section size grows. Strength at matching ageing conditions is close enough that the choice is usually made on toughness, not strength.
Which standard covers XM-12 forgings?
ASTM A705 / A705M, Standard Specification for Age-Hardening Stainless Steel Forgings, adopted as ASME SA-705 in Section II of the Boiler and Pressure Vessel Code. Bars and shapes fall under ASTM A564 / A564M. ASTM B564 does not apply to this grade at all, since that specification covers nickel and nickel-copper alloy forgings.
Which heat treatment condition should be specified?
Order Condition A if you intend to machine and age the part yourself. Otherwise pick on required strength: H900 for the maximum 1310 MPa, H1025 as the general-purpose choice, H1150 or H1150M where toughness and stress-corrosion resistance matter more than strength.
What size XM-12 forgings can you make?
Seamless rolled rings from OD 50 mm to OD 6,000 mm, and single open-die forged pieces up to 30 tonnes, limited by the 60 t heat size and the 6,300 t press. Minimum order is 10 kg with no minimum piece count.
Can you supply XM-12 to AMS 5659 instead of ASTM A705?
Yes, subject to melt route. AMS 5659 and AMS 5862 apply tighter chemistry and melting requirements than A705 and generally call for consumable-electrode remelted material, which we produce in-house on the ESR and VAR furnaces.
Ask for a price on XM-12 forgings
Send a drawing, or just the rough dimensions, grade, heat-treatment condition, quantity and governing standard. Quotations go out within 24 hours on working days.
Jiangyin Jiangnan Metal Co., Ltd.
Melting works, open-die forge and ring rolling mill, operating since 1997
No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Telephone, WhatsApp and WeChat: +86 189 2135 9659
Email: sales@steelforgepieces.com