No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu, China Tel +86-189-2135-9659 Email sales@steelforgepieces.com
Open-Die Forging Factory
JJM Jiangyin Jiangnan Metal Co., Ltd. Open-Die Forgings, Seamless Rolled Rings, Forged Bars

X17CrNi16-2 (1.4057 / AISI 431) Open-Die Forgings

Forged bars, seamless rolled rings, discs, hollow bars, shafts, spindles, piston rods and pump and valve parts in martensitic stainless steel X17CrNi16-2, manufactured in Jiangyin, China.

Manufacturer: Jiangyin Jiangnan Metal Co., Ltd. Page last reviewed: Material standard: EN 10088-3 / EN 10250-4

Summary

X17CrNi16-2 (EN material number 1.4057, AISI 431, UNS S43100) is a martensitic chromium-nickel stainless steel with 0.12-0.22 % C, 15.0-17.0 % Cr and 1.5-2.5 % Ni. The nickel addition gives it higher toughness and better corrosion resistance than the plain 12 % chromium martensitic grades. It is normally used quenched and tempered to +QT800 (Rm 800-950 MPa) or +QT900 (Rm 900-1050 MPa), is ferromagnetic, machines well, forges well, and is usable to about 400 °C.

Jiangyin Jiangnan Metal Co., Ltd., an open-die forging factory at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China, supplies X17CrNi16-2 as forged round, square, flat and hex bars, forged and seamless rolled rings, discs and blocks, hollow bars and sleeves, and machined shafts, spindles, piston rods and valve components. Enquiries: +86-189-2135-9659, sales@steelforgepieces.com.

EN designation
1.4057X17CrNi16-2
US equivalent
AISI 431UNS S43100
Density
7.70kg/dm³
Tensile, +QT800
800-950MPa, Rp0.2 min 600 MPa
Forging range
1180-950°C, slow cooling
Magnetic
Yesferromagnetic grade

1. Grade description

X17CrNi16-2 is the EN designation for a hardenable corrosion-resisting chromium-nickel steel that transforms to martensite on quenching. It is specified where the 12 % chromium martensitic grades do not give enough corrosion resistance, or where their toughness falls short. The 15-17 % chromium content raises corrosion resistance, and the 1.5-2.5 % nickel addition keeps the structure fully martensitic rather than part ferritic at that chromium level, which is what preserves impact toughness after heat treatment.

The grade appears in several European standards, which matters when writing a purchase specification. It is covered by EN 10088-1 (list of stainless steels), EN 10088-3 (semi-finished products, bars, rods, sections and bright products), EN 10088-5 (construction purposes), EN 10272 (stainless steel bars for pressure purposes) and EN 10250-4, Open steel die forgings for general engineering purposes: stainless steels. Use within the scope of the European Pressure Equipment Directive is possible subject to prior agreement.

In practice the grade is a trade-off. Corrosion resistance, mechanical properties, forgeability and machinability are all rated good; weldability is rated poor, and the service ceiling is around 400 °C. The pitting resistance equivalent is 17.5 to 21.26, placing it among the moderately corrosion-resistant steels. It does not replace 316L or a duplex grade in chloride service.

2. Chemical composition

Chemical composition in % by mass. EN values per EN 10088; ASTM values for the nearest US grade.
Standard and gradeCSiMnPSCrNi
EN X17CrNi16-2 (1.4057)0.12-0.22max 1.00max 1.50max 0.040max 0.03015.0-17.01.5-2.5
ASTM AISI 431 / UNS S43100max 0.20max 1.00max 1.00max 0.040max 0.03015.0-17.01.25-2.5
LW 1.40440.12-0.20max 1.00max 1.00max 0.035max 0.02515.0-18.02.0-3.0
EN X19CrNi17-20.14-0.23max 1.00max 1.00max 0.040max 0.01515.5-17.51.5-2.5
AFNOR Z15CN16-020.15-0.20max 1.00max 1.00max 0.040max 0.02515.5-17.01.5-2.5
GOST 14Ch17N20.11-0.17max 0.80max 0.80max 0.030max 0.02516.0-18.01.5-2.5
GOST 20Ch17N20.17-0.25max 0.80max 0.80max 0.035max 0.02516.0-18.01.5-2.5
PN H17N2A0.11-0.17max 0.80max 0.80max 0.035max 0.02016.0-18.01.5-2.5

The EN and ASTM windows are not identical. AISI 431 allows nickel down to 1.25 % and limits manganese to 1.00 %, while X17CrNi16-2 permits up to 1.50 % Mn and sets a carbon floor of 0.12 %. Where a drawing calls for dual certification, we restrict the melt analysis to the overlap of both windows. State this at the enquiry stage so the heat can be selected accordingly.

3. Equivalents and other designations

Cross-reference of designations for X17CrNi16-2 / 1.4057.
System or countryDesignation
EN and Werkstoffnummer (Europe)X17CrNi16-2, X 17 CrNi 16-2, 1.4057, DIN 17440 1.4057
ASTM / AISI / UNS (USA)AISI 431, UNS S43100, Aeralloy 431-C
AerospaceAMS 5628, WL 1.4044, AIR 9160 Z15CN17-03, ASNA 3126 / 3138 / 3299
JIS (Japan)SUS 431
BS (United Kingdom)431S29, 321S31, S80
AFNOR (France)Z15CN16-02, Z15CN17-03, Z15CN17.03
SIS (Sweden)2321
GOST (Russia and CIS)14Ch17N2 (14172), 20Ch17N2 (20172), 1Ch17N2
PN (Poland)H17N2, H17N2A, 2H17N2
Close variants1.4044, X19CrNi17-2, X20CrNi17-2, X22CrNi17, X16CrNi16, X14CrNi172
Equivalence is approximate. Cross-reference tables match grades by chemistry family, not by guaranteed properties, test regime or delivery condition. 1.4044 and X19CrNi17-2 sit at different nickel and sulphur levels. Where a code case or customer specification applies, order to the exact standard named on the drawing and we certify to that standard.

4. Mechanical properties

Properties depend on the delivery condition. The number after QT is the minimum tensile strength in N/mm², so +QT900 is the stronger and +QT800 the tougher of the two standard quenched and tempered conditions.

Room temperature properties, longitudinal, per EN 10088-3 together with typical mill values.
ConditionRp0.2 (MPa)Rm (MPa)A5 (%)ISO-V at 20 °C (J)Hardness HB
+A annealedapprox. 275max 950--max 295
+QT800 specifiedmin 600800-950min 14min 25-
+QT800 typical62082020-approx. 251-299
+QT900 specifiedmin 700900-1050min 12min 25-
+QT900 typical71092016--

Elongation and impact values are section sensitive. In +QT800, EN 10088-3 requires A at least 14 % and KV at least 25 J up to 60 mm, relaxing to A at least 12 % and KV at least 20 J above 60 mm. Above roughly 160 mm the properties are agreed between purchaser and supplier. For heavy open-die forgings we quote guaranteed values against the actual ruling section and the test location, whether surface, mid-radius or centre, rather than against the bar-stock table.

In the annealed condition the yield strength is only about 275 MPa, so the grade is normally machined or cold formed soft and hardened afterwards. Where straightening is applied to profiles up to 35 mm, cold work can raise hardness by up to about 60 HB and tensile strength by up to about 150 N/mm² above the annealed figures.

Minimum proof stress at elevated temperature

Minimum 0.2 % proof stress Rp0.2 in MPa at temperature, per EN 10088-3.
Condition100 °C150 °C200 °C250 °C300 °C350 °C400 °C
+QT800515495475460440405355
+QT900565525505490470430375

5. Physical properties

Physical properties of X17CrNi16-2 (1.4057).
PropertyValue
Density7.70 kg/dm³ (7.7 g/cm³)
Electrical resistivity at 20 °C0.70 Ω·mm²/m
Thermal conductivity at 20 °C25 W/(m·K)
Specific heat capacity at 20 °C460 J/(kg·K)
Coefficient of thermal expansion10.0 x 10-6 K-1 (20-100 °C); 10.5 x 10-6 K-1 (20-200, 20-300 and 20-400 °C)
MagnetisabilityYes, ferromagnetic in all conditions
Maximum service temperatureapprox. 400 °C
PRE, pitting resistance equivalent17.5 to 21.26

Because the grade is ferromagnetic, forgings in X17CrNi16-2 can be inspected by magnetic particle testing, where austenitic stainless steels require dye penetrant instead. We supply MT, PT, UT and hardness survey reports with the forging on request.

6. Forging and heat treatment

Forging

Heat gradually to about 850 °C, then heat more rapidly to 1150-1180 °C. Forge between 1180 °C and 950 °C, finishing before the metal drops below the lower limit, then cool slowly in a furnace or buried in dry ash or similar. Slow cooling is not optional on this grade. The steel is air hardening, so air cooling a heavy section straight from forging risks quench cracking.

Soft annealing (+A)

Hold between 680 °C and 800 °C, then cool slowly in the furnace or in air. This is the condition in which the forging is normally rough machined.

Hardening and tempering

Austenitise between 950 °C and 1060 °C and quench in oil or air. Tempering then sets the strength level. For +QT800, temper at 750-800 °C followed by a second temper at 650-700 °C. For +QT900, temper at 600-650 °C. Where the nickel content of the particular heat sits at the low end of the specification, a single temper between 620 °C and 720 °C is sufficient for +QT800.

475 °C embrittlement. X17CrNi16-2 is susceptible to embrittlement in the 420-520 °C band. Exposure to this range has to be limited during fabrication and in service, which is the main reason the practical service ceiling is set around 400 °C.

7. Machining, welding and corrosion behaviour

Machinability

Machinability is rated good and is governed largely by hardness. The steel cuts much like a carbon steel of equivalent hardness and is easier to machine than conventional austenitic stainless steels, which work harden and gall. As a starting point with coated carbide tooling on solution annealed material at Rm 700-800 N/mm²: 100 m/min at 6 mm depth of cut and 0.5 mm/rev feed, 130 m/min at 3 mm and 0.4 mm/rev, and 165 m/min at 1 mm and 0.2 mm/rev. The grade takes a good polish and suits automated machining as well as hammer and die forging.

Welding

Weldability is rated poor, so the procedure needs control. With a matching filler, preheat the workpiece to 100-300 °C and temper it as soon as possible after welding to restore ductility in the weld zone. For optimum properties, re-heat-treat the whole component. Where weld metal strength is not critical, an austenitic filler such as a 4430 or 4370 type consumable can be used and preheating is then not required. Avoid nitrogen and carbon bearing shielding gases, which degrade weld properties, and remove spatter and heat tint afterwards to restore corrosion resistance. Cold forming and cold heading are not common practice on this grade.

Corrosion resistance

Corrosion resistance is good for a martensitic steel and is best in the hardened and tempered condition with a smooth polished surface. Surface finish has a marked effect: polished surfaces resist corrosion far better than rough surfaces on identical material. The grade resists nitric acid and other strongly oxidising acids, phosphoric acid, dilute formic and acetic acids, most nitrates, and sea water in intermittent service. Its limitation is intergranular corrosion, since chromium carbides precipitate and leave chromium-depleted regions around them. Welded or improperly tempered parts need post-weld heat treatment to maintain resistance.

8. Typical applications

X17CrNi16-2 is used in mechanical engineering, the chemical and petrochemical industries, the automotive sector, marine and shipbuilding work, aerospace, and the paper, nitrogen and food industries. Typical components include heavily loaded pump parts and pump casings, valve bodies, valve stems and valve internals, drive and propeller shafts, sleeves and bushings, spindles, piston rods, fittings, stirrers and mixing blades, gears, actuators, bearings, hydraulic rams, crane pins, bolts, nuts and other fasteners. The H17N2A variant is a special aerospace grade used for aircraft parts.

9. Forgings we manufacture in this grade

Forged bars

Round bars and rods, square and rectangular bars, flat bars and hex bars, rough turned, peeled or black as forged.

Forged and seamless rolled rings

Forged rings and radial-axial seamless rolled rings, including flange rings, gear blanks and bearing rings.

Discs, blocks and plates

Forged discs and disks, rectangular blocks, slabs and heavy forged plate for further machining.

Hollow bars and sleeves

Forged hollow bars, sleeves, bushes and bushings, pipes and tubes, barrels, casings, shells, cylinders, hubs and housings.

Shafts and long parts

Shafting, stepped shafts, spindles, piston rods and stems, forged and heat treated to +QT800 or +QT900.

Pump and valve forgings

Pump parts, valve parts, valve bodies and bonnets, and near-net-shape open-die and die forgings to drawing.

Delivery conditions available: as forged, +A annealed, +QT800 and +QT900. Standard documentation is an EN 10204 3.1 inspection certificate covering chemical analysis, mechanical test results and heat treatment records. Third-party inspection and witness testing can be arranged. Send the drawing, grade condition, quantity and required standard to sales@steelforgepieces.com for a quotation.

10. Frequently asked questions

What is X17CrNi16-2 steel?
X17CrNi16-2 (EN material number 1.4057) is a martensitic chromium-nickel stainless steel containing 0.12-0.22 % carbon, 15.0-17.0 % chromium and 1.5-2.5 % nickel. It is listed in EN 10088-1, EN 10088-3, EN 10088-5, EN 10272 and EN 10250-4, and is normally supplied quenched and tempered to +QT800 or +QT900. It is ferromagnetic and usable to about 400 °C.
What is X17CrNi16-2 equivalent to?
It corresponds to EN 1.4057, AISI 431, UNS S43100, SUS 431 in Japan, BS 431S29 and 321S31 in the UK, Z15CN16-02 and Z15CN17-03 in France, SIS 2321 in Sweden, AMS 5628 in aerospace, WL 1.4044 and X19CrNi17-2, GOST 14Ch17N2 and 20Ch17N2, and the Polish grades H17N2, H17N2A and 2H17N2. Equivalences are approximate, so order to the standard named on the drawing.
What is the difference between +QT800 and +QT900?
The figure after QT is the minimum tensile strength in N/mm². +QT800 is tempered at 750-800 °C with a second temper at 650-700 °C and gives Rm 800-950 MPa, Rp0.2 at least 600 MPa and A at least 14 %. +QT900 is tempered at 600-650 °C and gives Rm 900-1050 MPa, Rp0.2 at least 700 MPa and A at least 12 %. +QT800 is specified for toughness, +QT900 for strength.
Can X17CrNi16-2 be welded?
Yes, but weldability is rated poor and the procedure matters. With a matching filler, preheat to 100-300 °C and temper immediately after welding, and re-heat-treat the whole part for full properties. Austenitic fillers avoid the preheat where weld strength is not critical. Avoid nitrogen and carbon bearing shielding gases, and remove heat tint and spatter to restore corrosion resistance.
At what temperature is X17CrNi16-2 forged?
Heat gradually to about 850 °C, then more rapidly to 1150-1180 °C. Forge between 1180 °C and 950 °C and cool slowly in a furnace or dry ash. Avoid prolonged exposure to 420-520 °C at any stage because of 475 °C embrittlement.
Is X17CrNi16-2 magnetic?
Yes. It is ferromagnetic in every delivery condition, which means magnetic particle inspection can be used on finished forgings.
Who supplies X17CrNi16-2 open-die forgings?
Jiangyin Jiangnan Metal Co., Ltd., an open-die forging factory at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China, manufactures X17CrNi16-2 (1.4057 / AISI 431) forged bars, forged and seamless rolled rings, discs, hollow bars, shafts, spindles and pump and valve forgings. Contact +86-189-2135-9659 or sales@steelforgepieces.com.

References

  • EN 10088-1, EN 10088-3, EN 10088-5, EN 10272 and EN 10250-4 standard listings for 1.4057 – steelnumber.com
  • Deutsche Edelstahlwerke / Swiss Steel Group data sheet 1.4057, covering physical properties, heat treatment, forging, welding, machining and PRE – PDF data sheet
  • Comparative composition, delivery conditions and equivalents for X17CrNi16-2 / AISI 431 – Virgamet
  • Masteel UK and AZoM, Applications of Martensitic Stainless Steel 1.4057 QT800 – AZoM

Data on this page is compiled from the published standards and mill data sheets listed above and is given for general guidance. Guaranteed values for a specific order are those stated on the material certificate supplied with the forging.

Other martensitic and precipitation hardening stainless grades we forge: 17-4PH (1.4542), 17-7PH, PH13-8Mo. See also the stainless steel forging index, nickel alloy forgings including Incoloy 825 and Inconel X-750, and the full product range.