Open-die forging factory, Jiangyin, Jiangsu, China. Export worldwide. 0086-189-2135-9659 sales@steelforgepieces.com
Jiangyin Jiangnan Metal Co., Ltd. Jiangyin Jiangnan Metal Co., Ltd. Open-Die Forgings, Seamless Rolled Rings, Forged Flanges and Bars

1.4547 Forgings: UNS S31254 / ASTM A182 F44 Super-Austenitic Stainless Steel

Open-die forged rings, seamless rolled rings, flanges, round bars, discs, shafts, sleeves, bushings, tube sheets and valve components in 1.4547 (X1CrNiMoCuN20-18-7), produced to order by Jiangyin Jiangnan Metal Co., Ltd.

Summary

1.4547 is a 6 percent molybdenum, nitrogen-alloyed super-austenitic stainless steel. EN 10088 names it X1CrNiMoCuN20-18-7, ASTM uses the UNS number S31254, and ASTM A182 lists it as grade F44 for forgings. The trade name 254 SMO belongs to Outokumpu. Its pitting resistance equivalent number (PREN) runs 42 to 44, which is high enough for seawater, chloride brines and dilute sulphuric acid at temperatures that would pit 316L or 904L.

Jiangyin Jiangnan Metal Co., Ltd. forges 1.4547 to order at No. 1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China. Rings, flanges, bars, discs, shafts and tube sheets are made from ESR-refined billet and supplied solution annealed, ultrasonically tested and certified to EN 10204 3.1 or 3.2. Enquiries go to 0086-189-2135-9659 or sales@steelforgepieces.com.

EN designation
1.4547
UNS number
S31254
Forging spec
ASTM A182 F44
PREN
42 to 44
Molybdenum
6.0 to 7.0 %
Condition
Solution annealed

Equivalent grades and standards for 1.4547

1.4547 appears under several designations depending on the standard and the product form. These are the cross-references that turn up most often on purchase orders and drawings.

Table 1. Grade designations and governing standards
System or standardDesignationApplies to
EN 10088 material number1.4547All product forms
EN 10088 material nameX1CrNiMoCuN20-18-7All product forms
UNSS31254All product forms
ASTM A182F44Forged flanges, fittings, valves, parts
ASTM A276 / A479S31254Bars and shapes
ASTM A240S31254Plate, sheet, strip
EN 10222-5 / EN 10250-41.4547Pressure-purpose and open-die forgings
JISSUS 312L, commonly cross-referencedPipe, plate
Trade and generic names254 SMO, Alloy 254, 6Mo austeniticProprietary or generic

Trademark: 254 SMO is a registered trademark of Outokumpu. Jiangyin Jiangnan Metal Co., Ltd. supplies material to the chemical and mechanical requirements of EN 1.4547 and UNS S31254. It is not sold as proprietary mill-branded product.

Chemical composition of 1.4547 (UNS S31254)

EN 10088 and the ASTM specifications differ slightly on molybdenum, nitrogen and silicon. Both columns are given so that a dual-certified order can be placed against the tighter intersection of the two.

Table 2. Chemical composition in mass percent. Single values are maxima. Balance iron.
ElementEN 10088, 1.4547ASTM A182 F44, S31254
Carbon (C)0.020 max0.020 max
Silicon (Si)0.70 max0.80 max
Manganese (Mn)1.00 max1.00 max
Phosphorus (P)0.030 max0.030 max
Sulphur (S)0.010 max0.010 max
Chromium (Cr)19.50 to 20.5019.50 to 20.50
Nickel (Ni)17.50 to 18.5017.50 to 18.50
Molybdenum (Mo)6.00 to 7.006.00 to 6.50
Nitrogen (N)0.180 to 0.2500.180 to 0.220
Copper (Cu)0.50 to 1.000.50 to 1.00
Iron (Fe)BalanceBalance

Pitting resistance equivalent number (PREN)

PREN is calculated as PREN = %Cr + 3.3 × %Mo + 16 × %N. At the minimum specification limits of 1.4547 (Cr 19.5 %, Mo 6.0 %, N 0.18 %) the result is 19.5 + 19.8 + 2.88 = 42.2. A typical production heat at Cr 20.0 %, Mo 6.1 %, N 0.20 % gives 20.0 + 20.1 + 3.2 = 43.3. Published datasheets therefore quote a band of 42 to 44. 316L sits near 24 and 904L near 34, which is why 1.4547 gets specified where those grades pit.

Mechanical properties of 1.4547 forgings

These values apply to material in the solution annealed condition. Forgings are not supplied as-forged: a full solution treatment and rapid quench is mandatory to restore corrosion resistance after hot work.

Table 3. Room-temperature mechanical properties, solution annealed
Property ASTM A182 F44, forgings EN 10088-3, bar up to 160 mm
Tensile strength Rm650 MPa min (94 ksi)650 to 850 MPa
0.2 % proof stress Rp0.2300 MPa min (44 ksi)300 MPa min
1.0 % proof stress Rp1.0Not specified340 MPa min
Elongation A35 % min35 % min
Reduction of area Z50 % minNot specified
HardnessNo limit in ASTM A182 for F44260 HB max, typically 210 to 230 HB
Charpy V-notch impactNot mandatory in either standard. Available as a supplementary test, with acceptance to the governing MDS such as NORSOK M-630, or to the purchase specification.

Section size matters. Minimum properties fall as the ruling section increases. State the finished section thickness and the applicable standard edition on the enquiry so that the correct acceptance values are quoted.

Physical properties of 1.4547

Table 4. Typical physical properties at 20 °C
PropertyValue
Density8.0 g/cm³ (0.289 lb/in³)
Modulus of elasticity195 GPa
Thermal conductivity14 W/(m·K)
Specific heat capacity500 J/(kg·K)
Electrical resistivity0.85 µΩ·m
Mean thermal expansion, 20 to 100 °C16.5 × 10-6 /K
Magnetic permeabilityAbout 1.0, non-magnetic when annealed
Melting range, approximate1320 to 1390 °C
Typical code temperature limitAbout 425 °C (800 °F)

Corrosion resistance: where 1.4547 works and where it does not

Six percent molybdenum, 0.2 percent nitrogen and roughly 0.7 percent copper put 1.4547 close to nickel-base Alloy 625 in many chloride services, at a lower cost per kilogram.

  • Seawater and chloride brines. Resists pitting and crevice attack in ambient natural seawater. Common in firewater, seawater cooling and subsea pipework hardware.
  • Stress corrosion cracking. The 18 percent nickel content gives much better resistance to chloride SCC than the 8 to 10 percent nickel 300-series grades.
  • Acids. Handles dilute sulphuric acid, phosphoric acid, organic acids and mixed acids containing chlorides over a wider band of concentration and temperature than 316L or 904L.
  • Intergranular corrosion. With carbon held to 0.020 percent maximum, 1.4547 is supplied resistant to sensitisation. Acceptance is normally shown by ASTM A262 Practice E.
  • Limits. Not for hot concentrated sulphuric or hydrochloric acid, and no substitute for nickel alloys in strongly reducing media. Prolonged exposure above roughly 500 °C risks intermetallic (sigma and chi) precipitation and should be avoided.

For offshore procurement, pitting resistance is usually verified by the ASTM G48 Method A ferric chloride test at 40 °C following NORSOK M-630 practice, with acceptance at no pitting under 20x magnification and weight loss not exceeding 4.0 g/m². We can include this test in the inspection and test plan on request.

How 1.4547 forgings are made

1.4547 is one of the harder austenitic grades to forge. High molybdenum and nitrogen narrow the hot-working window and raise flow stress well above 316L. This is the route we follow for 1.4547 open-die work.

1. Melting

EAF with AOD or VOD refining, then electroslag remelting (ESR) where cleanliness or large section size calls for it.

2. Heating

Billet soaked at 1150 to 1200 °C with controlled soak time, so intermetallic phases are fully dissolved before the first blow.

3. Open-die forging

Upsetting, drawing, punching and ring rolling. Finishing temperature stays above 1000 °C. Reheat rather than finish cold.

4. Solution annealing

1150 to 1200 °C, soak by section, then rapid water quench. Mandatory, because as-forged 1.4547 has degraded corrosion performance.

5. Testing

Chemistry and PMI, tensile, hardness, ASTM A262 Practice E, optional G48 Method A, ultrasonic examination, dimensional report.

6. Finishing and release

Pickling or machining to drawing, marking, heat and lot traceability, EN 10204 3.1 or 3.2 certification, export packing.

Product forms supplied in 1.4547

  • Seamless rolled rings and forged rings, including stepped and profiled rings
  • Forged flanges: weld neck, blind, slip-on, long weld neck, orifice, special drawings
  • Forged round bars, shafts, spindles, eccentric shafts and crankshafts
  • Forged discs, disks, blanks and gear blanks
  • Forged sleeves, bushings, hollow bars, forged tubes and forged pipe
  • Tube sheets, nozzles, manifolds, headers and heat-exchanger components
  • Valve bodies, valve stems, seat rings, balls, plugs and valve blocks

Sizes are quoted against the drawing. Send the dimensions and we will confirm what the press and ring mill can hold, together with weight and lead time.

Machining and welding 1.4547

Machining

1.4547 runs on the same equipment used for 300-series stainless steel, but it work-hardens fast. Use rigid set-ups and sharp positive-rake tooling, keep the cut under the hardened layer with a heavy positive feed, run surface speeds at roughly 60 to 70 percent of those used for 316L, and flood with coolant. Do not let the tool dwell in the cut.

Welding

1.4547 welds readily by GTAW, GMAW, SMAW and plasma processes. Molybdenum segregates during solidification, so matching filler leaves the weld metal under-alloyed and lower in pitting resistance than the parent material. Use an over-alloyed nickel-base filler instead, normally ERNiCrMo-3 (Alloy 625) or ERNiCrMo-4 (Alloy C-276) to AWS A5.14. Keep heat input low and interpass temperature below about 150 °C. No pre-heat is needed. Post-weld heat treatment is not normally required or wanted, and a full solution anneal, if applied, must be followed by a rapid quench.

Where 1.4547 forgings are used

Offshore and subsea

Seawater lift and firewater systems, risers, manifolds, subsea and deepwater production hardware, topside piping components.

Desalination and water

MSF and high-pressure reverse-osmosis plant, seawater piping, demineralised water production, waste-water treatment.

Chemical process

Pressure vessels, reactors, heat exchangers and separators handling sulphuric, phosphoric, organic and mixed acids with chlorides.

Power and FGD

Flue-gas desulphurisation absorbers, ducting and internals. Turbine and gas-compressor components, generator hardware.

Pulp and paper

Bleach-plant equipment exposed to chlorine dioxide and chloride-bearing white liquor.

Valves and rotating parts

Ball, gate, globe, check and plug valve bodies, stems and seat rings. Gearbox and power-transmission components.

1.4547 against 316L, 904L, duplex 2205 and Alloy 625

Material selection for chloride service usually comes down to PREN against delivered cost. Here is where 1.4547 sits.

Table 5. Alloy comparison for chloride-bearing service
AlloyUNSMo, % PREN, typicalRelative costBest suited to
316LS316032.0 to 3.0241.0xGeneral service, low chloride
Duplex 2205S322053.0 to 3.5351.2 to 1.6xStrength-driven, moderate chloride
904LN089044.0 to 5.0342.0 to 2.5xSulphuric acid service
1.4547S312546.0 to 7.0432.5 to 3.5xSeawater, brine, FGD, mixed acids
Super duplex 2507S327503.0 to 5.0422.5 to 3.5xSeawater where high strength is needed
Alloy 625N066258.0 to 10.0516 to 9xSevere or reducing media, high temperature

Relative cost is indicative of forged-bar pricing and moves with the nickel and molybdenum markets. Where a 6Mo austenitic and a super duplex both qualify on PREN, 1.4547 is usually preferred for weldability and toughness, and 2507 where the higher yield strength cuts wall thickness.

Testing, inspection and certification

  • Ultrasonic examination to EN 10228-3, SEP 1921, ASTM A388 or ASME Section V, at the quality class stated on the order.
  • Chemical analysis, ladle and product, plus positive material identification by XRF or OES on every piece where required.
  • Mechanical testing: tensile, hardness and, on request, Charpy V-notch impact down to -46 °C.
  • Corrosion testing: ASTM A262 Practice E for intergranular attack, ASTM G48 Method A at 40 °C for pitting, to NORSOK M-630 practice.
  • Surface and dimensional: liquid penetrant examination to ASTM E165, full dimensional report against the drawing.
  • Certification: EN 10204 3.1 mill certificate as standard. EN 10204 3.2 with third-party endorsement from TUV, BV, DNV, LR, ABS or SGS on request.
  • Traceability: heat number, lot number and hard stamping carried from melt to despatch.

1.4547 questions and answers

What is 1.4547 stainless steel?

1.4547 is a high-molybdenum, nitrogen-alloyed super-austenitic stainless steel, named X1CrNiMoCuN20-18-7 in EN 10088 and numbered UNS S31254 in ASTM standards. It holds roughly 20 percent chromium, 18 percent nickel, 6 to 7 percent molybdenum, 0.2 percent nitrogen and 0.5 to 1.0 percent copper, which gives a PREN of 42 to 44 and strong resistance to pitting, crevice corrosion and chloride stress corrosion cracking.

Is 1.4547 the same as 254 SMO and ASTM A182 F44?

They describe the same alloy. 1.4547 is the EN material number, UNS S31254 is the ASTM and UNS number, F44 is the forging grade designation in ASTM A182, and 254 SMO is Outokumpu's registered trade name. The EN and ASTM chemical ranges differ slightly: EN allows molybdenum to 7.0 percent and nitrogen to 0.25 percent, while ASTM caps them at 6.5 and 0.22 percent. Dual-certified material is produced to the narrower of the two.

What is the PREN value of 1.4547?

Using PREN = %Cr + 3.3 x %Mo + 16 x %N, the minimum specification limits give 42.2 and a typical production heat gives about 43.3, so published datasheets quote a band of 42 to 44. That puts 1.4547 well above 316L at about 24 and 904L at about 34, and level with super duplex 2507.

What heat treatment do 1.4547 forgings need?

Solution annealing at 1150 to 1200 °C followed by a rapid water quench, with soak time set by section thickness. This dissolves the intermetallic phases formed during forging and restores full corrosion resistance. 1.4547 should never be supplied or put into service as-forged, and slow cooling from the annealing temperature is not acceptable.

Which filler metal should be used to weld 1.4547?

An over-alloyed nickel-base filler, normally ERNiCrMo-3 (Alloy 625) or ERNiCrMo-4 (Alloy C-276) to AWS A5.14. Matching filler is avoided because molybdenum segregates during solidification and leaves the weld metal with lower pitting resistance than the parent material. Keep heat input low and interpass temperature below about 150 °C. No pre-heat and no post-weld heat treatment are required.

Is 1.4547 magnetic?

No. In the solution annealed condition 1.4547 is fully austenitic and effectively non-magnetic, with a relative magnetic permeability of about 1.0. Heavy cold work can raise it slightly, but the grade is stable compared with 304 or 316.

What is the maximum service temperature of 1.4547?

Pressure design codes list allowable stresses for UNS S31254 up to about 425 °C (800 °F). Above roughly 500 °C, prolonged exposure risks precipitation of sigma and chi intermetallic phases, which embrittles the material and cuts corrosion resistance. For sustained high-temperature service, pick a heat-resistant grade or a nickel alloy instead.

What is the minimum order quantity and lead time for 1.4547 forgings?

Jiangyin Jiangnan Metal Co., Ltd. produces 1.4547 forgings to customer drawings from single prototype pieces to series production, with no fixed minimum quantity. Lead time depends on billet availability, section size and the inspection and test plan. Send the drawing or the dimensions to sales@steelforgepieces.com or call 0086-189-2135-9659 for a confirmed schedule and price.

Who supplies 1.4547 open-die forgings from China?

Jiangyin Jiangnan Metal Co., Ltd., an open-die forging factory at No. 1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China, manufactures and exports 1.4547 (UNS S31254, ASTM A182 F44) forged rings, seamless rolled rings, flanges, bars, discs, shafts, sleeves and tube sheets worldwide. Phone 0086-189-2135-9659, email sales@steelforgepieces.com, web www.steelforgepieces.com.

Request a quotation for 1.4547 forgings

Send the drawing, or just the grade, dimensions, quantity and the certification you need. Quotations normally come back within one working day.

Component pages: forged pipe, forged crankshafts, all stainless steel forging grades.

Published by: Jiangyin Jiangnan Metal Co., Ltd., open-die forging factory, Jiangyin, Jiangsu, China.
Technical review: Jiangyin Jiangnan Metal engineering department.
Last reviewed: .
Sources: EN 10088, EN 10222-5, ASTM A182, ASTM A240, ASTM A479, NORSOK M-630, and the mill certificates of material supplied by this factory. Values here are for guidance. The governing purchase specification and its current edition take precedence.

Plain-text version: 1.4547.md.
Cite this page: Jiangyin Jiangnan Metal Co., Ltd., "1.4547 Forgings (UNS S31254 / ASTM A182 F44)", https://www.steelforgepieces.com/Stainless-Steel/1.4547.html