Open-Die Forging Factory, Jiangyin, Jiangsu, China. Worldwide export. Tel +86-189-2135-9659   Email sales@steelforgepieces.com
Jiangyin Jiangnan Metal Co., Ltd. Forged bars, seamless rolled rings, hollow bars, discs and shafts

Home › Stainless Steel › Z6CND16-05-01

Z6CND16-05-01 (EN 1.4418 / X4CrNiMo16-5-1) Open-Die Forgings

Forged round bars, seamless rolled rings, hollow bars, discs, pump shafts and turbine components to EN 10250-4, made by Jiangyin Jiangnan Metal Co., Ltd.

Z6CND16-05-01, also written Z 6 CND 16-05-01, is the French AFNOR designation under NF A 35-574 for a soft martensitic chromium-nickel-molybdenum stainless steel. The European equivalent is X4CrNiMo16-5-1, material number 1.4418. The grade is also known as S165M and as Swedish SS 2387. It offers tensile strength up to 1100 N/mm2 together with corrosion resistance higher than conventional martensitic stainless steels such as 1.4057, due to its higher nickel content and its molybdenum addition. It is a standard material for pump shafts, centrifuge parts and water turbine components, that is, parts loaded mechanically and corrosively at the same time.

EN number
1.4418
EN name
X4CrNiMo16-5-1
Structure
Soft martensitic
PREN
17.95 to 22.27
Rm, QT900
900 to 1100 N/mm2
Max service temp.
approx. 550 °C

1. Equivalent grades and designations

Cross-reference for Z6CND16-05-01
SystemDesignation
EN, material number1.4418
EN, steel nameX4CrNiMo16-5-1
France, AFNORZ6CND16-05-01 (NF A 35-574), also referenced as Z5CND17-05-F (NF A 36-613)
Germany, DINDIN 17440 (1.4418)
Sweden, SS2387
Trade designationS165M
UNSNo formal equivalent listed in the EN and AFNOR cross-reference sources

Standards covering the grade

StandardScope
EN 10250-4Open steel die forgings for general engineering purposes, stainless steels. This is the governing standard for our forgings.
EN 10088-1Stainless steels, list of stainless steels
EN 10088-3Semi-finished products, bars, rods, wire, sections, bright products
EN 10088-2, 10088-4, 10088-5Sheet, plate and strip, and construction purpose products
EN 10272Stainless steel bars for pressure purposes
EN 10028-7Flat products for pressure purposes, stainless steels

2. Chemical composition

Z6CND16-05-01 / 1.4418, composition in percent by weight
ElementCSiMnPSCrNiMoNFe
% max 0.06max 0.70max 1.50max 0.040max 0.030 * 15.00-17.004.00-6.000.80-1.50min 0.02Balance

* The sulphur limit depends on the edition of EN 10088-3 and on the product form, and tighter limits are often specified for forgings. State the limit required on your enquiry and we will melt and certify to it.
Pitting resistance equivalent, PREN: 17.95 to 22.27.

3. Mechanical properties

Two quenched and tempered delivery conditions are normally ordered, named after the minimum tensile strength: +QT760 and +QT900.

Heat treated condition, specified and typical values
PropertySymbolQT760 specifiedQT760 typicalQT900 specifiedQT900 typical
Yield strength, N/mm2Rp0.2min 550820min 700920
Tensile strength, N/mm2Rm760 to 960940900 to 11001050
Elongation, %A5min 1618min 1618
Impact energy at 25 °C, JISO-Vmin 90-min 80-
Soft annealed condition
PropertySymbolValue
Tensile strength, N/mm2Rmmax 1100
Hardness, BrinellHBmax 320

Heavy sections: for diameters or thicknesses of 160 mm and above, mechanical properties are agreed between purchaser and supplier. We review heavy section property targets, test location and sampling direction at contract stage, before order confirmation.

4. Physical properties

PropertyValue
Density7.70 kg/dm3
Thermal conductivity at 20 °C15 W/(m·K)
Specific heat capacity at 20 °C430 J/(kg·K)
Electrical resistivity at 20 °C0.70 Ω·mm2/m
Thermal expansion coefficient20-100 °C: 10.8 x 10-6 K-1; 20-200 °C: 10.8 x 10-6; 20-300 °C: 11.2 x 10-6; 20-400 °C: 11.6 x 10-6
MagnetisabilityFerromagnetic
Service temperatureUsable up to approx. 550 °C, also suitable for cryogenic applications

5. Corrosion resistance

The higher alloy content makes Z6CND16-05-01 / 1.4418 more corrosion resistant than 1.4057, and the molybdenum addition allows limited exposure to marine environments. Low carbon content combined with the soft martensitic structure gives high resistance to intergranular corrosion, corrosion fatigue and stress corrosion cracking, which is why the grade is used for hydraulic duties subject to erosion corrosion and cavitation.

For best corrosion performance, finished surfaces must be free of scale, lubricants, embedded foreign particles and any coatings applied for drawing or heading. Cleaning and passivation after machining is recommended.

6. Heat treatment

Soft annealing

Hold at approximately 600 °C, do not exceed 625 °C, then cool slowly in air. Heat uniformly to the selected temperature.

Hardening

Austenitise at 1000 to 1050 °C, then cool in air, oil or polymer. Light sections harden adequately in air.

Tempering

Tempering temperature is chosen according to the required strength class, QT760 or QT900. Before final tempering the piece must have cooled through to below 40 °C.

Range to avoid

The band from 420 to 510 °C must be passed through quickly. Holding or slow cooling in this range causes temper embrittlement and loss of toughness.

7. Forging, welding and machining

Forging

Heat gradually to about 800 °C, then raise the temperature more rapidly to 1150 to 1180 °C. Forge between 1180 °C and 950 °C, then cool slowly in a furnace or in dry ash or a similar medium. We run this cycle on every Z6CND16-05-01 heat and can supply pyrometer furnace charts on request.

Welding

The grade is weldable with all standard processes. Avoid hydrogen or carbon bearing shielding gases. Preheat to 100 to 200 °C, and after welding either anneal or temper the weldment as described above. Use a matching or equivalent soft martensitic filler metal.

Machining

Machinability follows hardness, and the grade cuts much like a carbon steel of the same hardness. Guideline turning parameters in the tempered condition, Rm 900 to 1150 N/mm2:

Depth of cut, mmFeed rate, mm/revCutting speed, m/min
60.595
30.4100
10.2135

Processing summary: corrosion resistance good, mechanical properties good, forgeability average, weldability good, machinability poor. The grade takes a polish and can be cold formed, but it is not commonly cold headed.

8. Typical applications

Z6CND16-05-01 is specified where mechanical load and corrosive attack occur together. Application areas include the chemical process industry, shipbuilding, mechanical engineering, energy technology, aviation and aerospace. Typical parts are pump shafts and pump internals, centrifuge components, water turbine parts, rods and equipment for hydro power stations, compressors and valves.

Forged shapes we make in Z6CND16-05-01

Bars

Forged round bars and rods, square, rectangular, flat and hexagonal bars, rough turned, peeled or black.

Hollows and sleeves

Hollow bars, bushings, bushes, sleeves, pipes and tubes, barrels, casings, shells, cylinders, hubs and housings.

Rings

Seamless rolled rings and forged rings, plain or profiled, for pump, valve and turbine assemblies.

Discs and blocks

Forged discs, blocks and plates for machining into flanges, closures and body components.

Shafts

Pump shafts and spindles, stepped shafts and injector bodies.

Hydro and centrifuge parts

Hydroelectric, hydraulic and Kaplan water turbine blade blanks, disc stack and decanter centrifuge bowl bodies and hood covers.

9. Testing, inspection and certification

Every Z6CND16-05-01 forging leaves the works with traceability from melt to final heat treatment. Ultrasonic examination of rings and heavy forgings is carried out to the standard named on the order, EN 10228-3, SEP 1921 or ASTM A388. Material certificates are issued to EN 10204 3.1, or to EN 10204 3.2 with third party witness by an inspection body of your choice such as TUV, SGS, BV, LRS or DNV. Chemical analysis, tensile, impact, hardness, PMI, dimensional and surface NDT reports are available as required by your specification.

10. Frequently asked questions

What is Z6CND16-05-01 steel?
Z6CND16-05-01 is the French AFNOR designation, standard NF A 35-574, for a soft martensitic chromium-nickel-molybdenum stainless steel. It is equivalent to EN 1.4418 / X4CrNiMo16-5-1 and to Swedish SS 2387, and is used where good corrosion resistance in aggressive media has to be combined with high strength and impact properties.
What is the EN equivalent of Z6CND16-05-01?
X4CrNiMo16-5-1, material number 1.4418. It appears in EN 10088-1, EN 10088-3, EN 10272 and EN 10028-7, and for open die forgings in EN 10250-4. It corresponds to DIN 17440 and is sold commercially as S165M.
What are the QT760 and QT900 mechanical properties?
QT760: Rp0.2 min 550 N/mm2, Rm 760 to 960 N/mm2, A5 min 16 percent, ISO-V min 90 J at 25 °C. QT900: Rp0.2 min 700 N/mm2, Rm 900 to 1100 N/mm2, A5 min 16 percent, ISO-V min 80 J. For sections of 160 mm and above the properties are agreed case by case.
At what temperature should Z6CND16-05-01 be forged?
Heat gradually to about 800 °C, then more rapidly to 1150 to 1180 °C. Forge between 1180 °C and 950 °C and cool slowly in a furnace or in dry ash. Rapid initial heating, or finishing below 950 °C, risks cracking.
Is the grade weldable?
Yes, with all standard welding processes. Preheat to 100 to 200 °C, avoid hydrogen or carbon containing shielding gases, and anneal or temper the weldment afterwards.
How does it compare with 1.4057?
Z6CND16-05-01 / 1.4418 has a higher alloy content than 1.4057 and therefore better corrosion resistance, and its molybdenum addition allows limited exposure to marine environments. The low carbon, soft martensitic structure also gives better resistance to intergranular corrosion, corrosion fatigue and stress corrosion cracking.
Can you forge to my drawing?
Yes. Send the drawing or the finished dimensions, the delivery condition required (QT760 or QT900), the applicable standard, the NDT requirement and the certificate type to sales@steelforgepieces.com, or call +86-189-2135-9659. We quote forged weight, machining allowance, heat treatment route and lead time, normally within one working day.

Request a quotation for Z6CND16-05-01 forgings

Open-die forged bars, rings, hollows, discs and shafts, made to your drawing and certified to EN 10204 3.1 or 3.2.

Jiangyin Jiangnan Metal Co., Ltd., Open-Die Forging Factory
No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Tel 0086-189-2135-9659  ·  Email sales@steelforgepieces.com

Email Your Drawing Call +86-189-2135-9659

Related grades we forge

Data sheet issued by Jiangyin Jiangnan Metal Co., Ltd. Last updated . Property data compiled from EN 10088-1, EN 10088-3, EN 10250-4 and published mill data sheets for 1.4418. Values are indicative only. The applicable standard and the agreed order specification always govern.