Seamless rolled rings
Radial-axial rolled, solution annealed and quenched. The classic form for this grade in naval and seawater service.
Material number 1.3964 is a niobium stabilised, nitrogen bearing austenitic chromium nickel manganese stainless steel. It is specified where a loaded component has to stay non-magnetizable and resist seawater at the same time. The two product forms we make, open-die forgings and seamless rolled rings, are the forms covered by WL 1.3964-3 and WL 1.3964-6.
X2CrNiMnMoNNb21-16-5-3, material number 1.3964, contains about 21 per cent chromium, 16 per cent nickel, 5 per cent manganese and 3 per cent molybdenum with 0.20 to 0.35 per cent nitrogen. The alloy content holds the austenite stable, so the steel stays non-magnetizable at a relative permeability near 1.04, while nitrogen raises the proof strength above a conventional chromium nickel molybdenum grade. It is solution annealed at 1020 to 1050 C and cooled rapidly, and it is forged between 900 and 1100 C. The documented use is non-magnetizable seawater proof rolled rings for German Navy vessels, together with non-magnetic machine parts, cryogenic equipment and instrumentation hardware.
The designation reads directly as the analysis. X for high alloy, 2 for a carbon ceiling near 0.02 to 0.03 per cent, then chromium at 21, nickel at 16, manganese at 5 and molybdenum at 3 per cent, with nitrogen and niobium flagged as deliberate additions. Niobium stabilisation together with the 0.03 per cent carbon limit stops chromium carbides forming at the grain boundaries during welding, which is why the steel keeps its resistance to intercrystalline corrosion to DIN EN ISO 3651-2 in the sensitised condition.
The property that sells it is magnetic neutrality under load. Many austenitic stainless steels transform partly to martensite when they are cold worked and turn weakly magnetic. The nickel, manganese and nitrogen content of 1.3964 suppresses that transformation, so relative permeability stays close to unity after forming. Deutsche Edelstahlwerke quotes 1.04 for the grade. voestalpine quotes below 1.01 for its own product. Either figure is far below what a worked 316 would read.
| Element | C | Si | Mn | P | S | Cr | Ni | Mo | Nb | N |
|---|---|---|---|---|---|---|---|---|---|---|
| Specified | max. 0.03 | max. 1.00 | 4.00 to 6.00 | max. 0.025 | max. 0.010 | 20.00 to 21.50 | 15.00 to 17.00 | 3.00 to 3.50 | max. 0.25 | 0.20 to 0.35 |
Balance iron. Sulphur is held to 0.010 per cent, tight for an austenitic grade, to protect hot ductility during forging and to remove sulphide initiation sites in service.
This grade is routinely cross-referenced to Alloy 50, UNS S20910 and XM-19, and in conversation the names get used as if they were one steel. For a purchase order they are not. voestalpine states that 1.3964 is the European variant defined by DIN EN chemical limits, while Alloy 50 is the American grade under ASTM and AISI with its own limits. The nickel and molybdenum bands are the part that matters.
| Element or property | 1.3964, SEW 390 | S20910 / XM-19, ASTM A479 | Effect on the buyer |
|---|---|---|---|
| Carbon | max. 0.03 | max. 0.06 | 1.3964 is the low carbon, weld stable variant |
| Nickel | 15.0 to 17.0 | 11.5 to 13.5 | More austenite stability in 1.3964 |
| Molybdenum | 3.0 to 3.5 | 1.5 to 3.0 | Higher pitting resistance floor in 1.3964 |
| Chromium | 20.0 to 21.5 | 20.0 to 23.5 | Wider American band |
| Vanadium | not specified | 0.10 to 0.30 | Deliberate addition only in S20910 |
| Property | Symbol | Longitudinal | Transverse and tangential |
|---|---|---|---|
| Yield strength | Rp0.2 | min. 365 MPa | min. 365 MPa |
| Tensile strength | Rm | 700 to 950 MPa | 700 to 950 MPa |
| Elongation | A | min. 35 per cent | min. 30 per cent |
| Impact energy | Av | min. 85 J | min. 55 J |
Test direction changes the acceptance level, which matters on a rolled ring where the coupon is normally taken tangentially. Above 160 mm section thickness the values are a matter of agreement rather than a guarantee from the table, because section size governs the quench rate through the wall. We state what is achievable on your geometry before the order is placed, not after the test report comes back.
| Property | Value |
|---|---|
| Density | 7.90 kg/dm³ |
| Electrical resistivity at 20 C | 0.70 ohm mm²/m |
| Thermal conductivity at 20 C | 14 W/m.K |
| Specific heat capacity at 20 C | 460 J/kg.K |
| Relative magnetic permeability | approx. 1.04 |
| Thermal expansion 20 to 100 C | 15.7 x 10-6 /K |
| Thermal expansion 20 to 200 C | 17.0 x 10-6 /K |
| Thermal expansion 20 to 300 C | 17.5 x 10-6 /K |
| Thermal expansion 20 to 400 C | 17.8 x 10-6 /K |
The pitting index for 1.3964 falls between 33.1 and 38.6, which places it above a standard 316L. It performs in rural, industrial and coastal atmospheres, in cold nitric and organic acids, and in chloride bearing media. Food and beverage service is workable where acid concentrations stay moderate.
Because carbon is capped at 0.03 per cent and niobium is present as a stabiliser, the steel resists intercrystalline corrosion after welding. Qualification to DIN EN ISO 3651-2 is the normal route, and ASTM A262 Practice E is accepted where the specification is written to American standards.
Preheat to 950 to 1150 C and forge between 900 and 1100 C. The forging is cooled rapidly in air or water after the last blow. Slow cooling through the intermediate range lets unwanted phases precipitate, and those phases cost both corrosion resistance and toughness. Our press and ring mill are laid out so parts reach the quench without an intermediate hold.
1020 to 1050 C, followed by rapid cooling in air or water. Higher ranges near 1066 to 1121 C circulate for this grade on trading sites. Those figures belong to Nitronic 50 literature and applying them to 1.3964 is a specification error.
The low carbon content means welding does not throw chromium carbides, so post-weld heat treatment is usually unnecessary. Fillers 1.3954 and 1.3984 are suitable. Post-weld solution annealing becomes worth doing only after heavy cold deformation or on very thick walls.
This steel work hardens quickly, so light hesitant cuts make the job worse by hardening the surface ahead of the tool. Rigid fixturing, firm engagement and coated carbide are the requirements. The published guideline values below apply to solution annealed material at Rm 560 to 640 MPa.
| Depth of cut | Feed rate | Cutting speed |
|---|---|---|
| 6 mm | 0.5 mm/rev | 110 m/min |
| 3 mm | 0.4 mm/rev | 125 m/min |
| 1 mm | 0.2 mm/rev | 150 m/min |
Hammer and die forging and automatic machining are both rated as workable for this grade. Cold forming and cold heading are workable in some cases only, so confirm the route with us at enquiry if the part depends on cold work.
Ultrasonic examination to EN 10228-3, SEP 1921 or ASTM A388 as specified, with EN 10204 3.1 certification or 3.2 countersigned by a third party. Because the grade is bought for magnetic neutrality, we also offer permeability measurement on the finished part rather than only on a coupon, since cold work from final machining is exactly where permeability drifts.
The WL 1.3964 family splits by product form. Quoting the suffix on the order makes the acceptance criteria unambiguous. Note that WL 1.3964-6 was reissued in August 2025, replacing the October 2008 edition, so confirm which edition your specification calls up.
| Sub-standard | Product form | Supply position |
|---|---|---|
| WL 1.3964-1 | Plate and sheet | On request, through a partner mill |
| WL 1.3964-2 | Round, flat and square bars | Forged and rolled bar |
| WL 1.3964-3 | Open-die forged parts | Made in house |
| WL 1.3964-6 | Seamless rolled rings | Made in house |
Radial-axial rolled, solution annealed and quenched. The classic form for this grade in naval and seawater service.
Solid and trepanned discs, hubs, covers and tube sheets, rough or finish machined to drawing.
Stepped shafts, pump shafts and spindles where magnetic neutrality has to come with strength.
Flanges, blinds, bodies, bonnets, seat rings and stems for chloride bearing duty.
Hollow forgings, sleeves, bushings and forged tube with bored or trepanned centres.
Non-standard geometry forged to drawing, with machining allowance agreed in advance.
| Dimension | Limit | Set by |
|---|---|---|
| Rolled ring outside diameter | up to 6,000 mm | 6 m radial-axial ring mill |
| Machined disc diameter | up to 5,000 mm | 5,000 mm vertical turning lathe |
| Shaft turned length | up to 14,000 mm | C61160 lathe, 15 m well furnace |
| Bored cylinders | 1,600 mm dia. x 10,000 mm | CNC deep-hole drilling machine |
| Single piece weight | up to 30,000 kg | 60 t maximum heat, 6,300 t press |
| Minimum order | 10 kg | Works policy, no minimum piece count |
| Lead time | 20 to 60 days | Route and heat treatment cycle |
These are plant limits across all grades. On 1.3964 the practical ceiling is normally ingot availability rather than press capacity, so the achievable size is confirmed against the drawing at enquiry.
The documented applications share one requirement. The part must not disturb a magnetic field, or must not be disturbed by one, while still carrying load in a corrosive environment.
Non-magnetizable seawater proof seamless rolled rings for German Navy vessels, the application the WL sub-standard was written around.
Mechanical and electrical engineering parts where permeability is a design constraint rather than an afterthought.
Low temperature systems, including liquefaction duty, using the toughness the grade keeps at cryogenic temperature.
Measurement and control hardware where a magnetic signature would corrupt the reading.
Scientific and medical imaging structures that call for very low magnetic permeability in load bearing parts.
Rotating and fluid handling components under combined corrosive and mechanical loading.
Several European mills sell 1.3964 under their own name. If an enquiry quotes one of these, it is this grade.
| Trade name | Supplier |
|---|---|
| Magnadur 3964 | Deutsche Edelstahlwerke Specialty Steel, Witten |
| P501 and BOEHLER P501 | voestalpine High Performance Metals Deutschland |
| BGH 3964 | BGH Edelstahl Siegen |
| Irrubigo 3964 | Schmidt + Clemens, Edelstahlwerk Kaiserau |
| Remy 1.3964 WW | Remystahl, Hagen |
| Alloy 50 | Enpar Sonderwerkstoffe, Gummersbach |
Trade name listing per Stahlschluessel 2019. Cross-references are guidance. Where a proprietary name appears on the drawing, confirm the governing standard with us so the certificate matches the specification.
To price a 1.3964 forging we need the drawing or the finished dimensions, the quantity, the governing standard or WL sub-standard, the delivery condition, and the NDT and certification level. Forged weight, machining allowance, heat treatment and test scope are quoted together, so the figure covers a part that can be accepted rather than a billet price.
Jiangyin Jiangnan Metal Co., Ltd.
No.1 Chengxiqiao Road, Zhouzhuang Town
Jiangyin City, Jiangsu Province, China
Tel +86 189 2135 9659
Email sales@steelforgepieces.com
No, although they are close relatives and are often cross-referenced. 1.3964 carries nickel at 15.0 to 17.0 per cent and molybdenum at 3.0 to 3.5 per cent. UNS S20910, XM-19 or Alloy 50 carries nickel at 11.5 to 13.5 per cent and molybdenum at 1.5 to 3.0 per cent, and adds vanadium. The European grade also limits carbon to 0.03 per cent against 0.06 per cent. Treat them as separate specifications on the order.
1020 to 1050 C, followed by rapid cooling in air or water. Figures near 1066 to 1121 C that appear online for this grade come from Nitronic 50 documentation and should not be applied here.
In the practical engineering sense, yes. Relative permeability is quoted at about 1.04 by Deutsche Edelstahlwerke and below 1.01 by voestalpine for its equivalent product. High nickel, manganese and nitrogen keep the austenite stable so cold work does not drive a significant martensitic transformation, though permeability does climb gradually with the degree of cold forming. On critical parts, have permeability measured after final machining.
Preheat to 950 to 1150 C and forge between 900 and 1100 C. Cool rapidly in air or water straight after forging to keep unwanted phases from precipitating.
Well enough that the WL sub-standard exists for non-magnetizable seawater proof rolled rings on German Navy vessels, with a pitting index of 33.1 to 38.6. The qualification worth knowing is that the manganese content works against pitting resistance compared with a low manganese steel of similar alloying, so for severe hot stagnant chloride service a super-duplex or 6Mo grade is the better choice.
Usually yes. Carbon is capped at 0.03 per cent and niobium stabilises the structure, so chromium carbides do not form during welding and resistance to intercrystalline corrosion to DIN EN ISO 3651-2 is retained. Fillers 1.3954 and 1.3984 suit. Post-weld solution annealing is worth doing only after heavy cold deformation or on very thick sections.
It work hardens quickly, so the surface hardens ahead of the tool if the feed is too light or the tool dwells. Use rigid setups and coated carbide. Guideline turning runs from 6 mm depth at 0.5 mm per revolution and 110 m/min for roughing, down to 1 mm depth at 0.2 mm per revolution and 150 m/min for finishing.
Plant limits are 6,000 mm ring outside diameter, 5,000 mm machined diameter, 14,000 mm shaft turning length, 1,600 by 10,000 mm bored, and 30,000 kg single piece weight. On 1.3964 the ceiling is usually ingot availability, so size is confirmed against the drawing. Minimum order 10 kg with no minimum piece count. Normal lead time 20 to 60 days.
Open-die forging works producing forged rings, seamless rolled rings, discs, shafts, flanges and bars in stainless steel, nickel alloy, tool steel and alloy steel, supplied with EN 10204 3.1 or 3.2 certification.
No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Open-die forging, ring rolling, heat treatment, machining