GRADE X1CrNiMoCuN24-22-8  /  W.-NR 1.4652  /  UNS S32654 MELTED AND FORGED IN JIANGYIN, CHINA +86 189 2135 9659  |  sales@steelforgepieces.com
Jiangyin Jiangnan Metal Melting works and open-die forge, since 1997 Send drawing for quote

HOME / STAINLESS STEEL / X1CRNIMOCUN24-22-8

X1CrNiMoCuN24-22-8 Forgings

EN 1.4652, UNS S32654, 654 SMO. Seamless rolled rings, forged rings, flanges, shafts, discs, tube sheets, sleeves and valve parts in super-austenitic 1.4652, melted and forged in one works by Jiangyin Jiangnan Metal Co., Ltd., Jiangyin, Jiangsu, China.

Grade recordEN 10088-3
Designation
X1CrNiMoCuN24-22-8, also written X1CrNiMoCuN24.22.8
Material number
1.4652
Equivalent
UNS S32654, trade name 654 SMO. ISO designation 4652-326-54-I
Type
Fully austenitic, super-austenitic. High molybdenum, high nitrogen
Standards
EN 10088-1, EN 10088-2, EN 10088-3, DIN EN 10088-3, ISO 15510
Composition
Cr 23.0–25.0, Ni 21.0–23.0, Mo 7.0–8.0, N 0.45–0.55, Mn 2.0–4.0, Cu 0.3–0.6, C max 0.020 per cent
Density
8.0 g/cm³ (0.289 lb/in³)
PREN
About 57 by Cr + 3.3 Mo + 16 N. Some mills quote above 60 using a higher nitrogen factor
Delivery condition
Solution annealed and water quenched (+AT)
Certification
EN 10204 3.1, or 3.2 countersigned by a third party
Supplied by
Jiangyin Jiangnan Metal Co., Ltd., No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China. sales@steelforgepieces.com, +86 189 2135 9659
01

What the grade is

X1CrNiMoCuN24-22-8, material number 1.4652, is a fully austenitic stainless steel and one of the most highly alloyed grades listed in EN 10088. The designation carries the analysis: extra-low carbon, nominally 24 per cent chromium, 22 per cent nickel and 8 per cent molybdenum, with copper and nitrogen added deliberately. Manganese is held at 2 to 4 per cent so the steel can hold 0.45 to 0.55 per cent nitrogen in solution. That nitrogen keeps the structure austenitic at this alloy level and lifts the proof strength well above a standard 316L.

Enquiries for this grade usually arrive after 316L, 904L or 254 SMO have failed in service or been ruled marginal at the design stage. Outside Europe the same steel is bought as UNS S32654, normally under the trade name 654 SMO. For pitting, crevice corrosion and chloride stress corrosion cracking it sits at the top of the austenitic stainless steels, close to the nickel-base alloys.

02

Chemical composition

X1CrNiMoCuN24-22-8 / 1.4652, per cent by weight, EN 10088-3
LimitCSiMnPSCrNiCuMoN
Min.––2.00––23.021.00.307.00.45
Max.0.0200.504.000.0300.00525.023.00.608.00.55

Balance iron, roughly 38 to 46 per cent. Sulphur is capped at 0.005 per cent, low even for a stainless steel, to protect hot ductility during forging and to remove sulphide initiation sites in service.

03

Mechanical properties

Specified room temperature properties, +AT, EN 10088-3, bars and sections to 50 mm
ConditionRm MPaRp0.2 MPaA long. %Hardness HBWKV2 long. J
Solution annealed, water quenched750–1000min. 430min. 40max. 310min. 100

Published typical values for solution annealed material sit above these minima, near 880 MPa tensile, 490 MPa proof, 45 per cent elongation and 90 J Charpy V-notch. Properties for heavier forged sections are agreed case by case. Test location, orientation and sampling frequency are fixed at order entry.

Typical physical properties at 20 C

Physical data, X1CrNiMoCuN24-22-8 / 1.4652
PropertyMetricImperial
Density8.0 g/cm³0.289 lb/in³
Elastic modulus210 GPa30 x 10⁶ psi
Shear modulus81 GPa12 x 10⁶ psi
Poisson ratio0.280.28
Thermal conductivity9.8 W/m.K5.7 BTU/h.ft.F
Specific heat460 J/kg.K0.11 BTU/lb.F
Thermal expansion15 µm/m.K8.3 µin/in.F
Melting range1410–1460 C2560–2650 F

Thermal conductivity is low even against other austenitic stainless steels. It governs heat exchanger and tube sheet detailing, and it sets the heating rates used on heavy sections.

04

Equivalent grades

International cross-reference
SystemDesignation
EN / DIN nameX1CrNiMoCuN24-22-8
EN / DIN number1.4652
UNS, USAS32654
Trade name654 SMO
ISO 155104652-326-54-I
China015Cr24Ni22Mo8Mn3CuN. S32652 appears in some cross-reference tables
Product standardsASTM A312, A213, A249 as S32654. EN 10216-5, EN 10217-7 as 1.4652

Cross-references are guidance. The very high alloy super-austenitics began as proprietary grades, so regional equivalents are not always chemically identical. State the governing standard and grade on the enquiry and we confirm what can be certified.

05

Corrosion resistance

Performance comes from 7 to 8 per cent molybdenum combined with about 0.5 per cent nitrogen and 24 per cent chromium. Using the pitting index PREN = Cr + 3.3 Mo + 16 N, the nominal analysis gives roughly 57. Suppliers applying a nitrogen coefficient of 30 publish figures above 60. On either calculation 1.4652 ranks ahead of 254 SMO and 904L for pitting and crevice attack in hot seawater and concentrated chloride brines. It is also specified for sulphuric acid, organic acids and mixed acids carrying chloride ions at higher pressure and temperature, and for media that are oxidising and chloride bearing at once, such as chlorine dioxide service.

06

Forging, heat treatment, fabrication

Hot working

Forged between 1095 and 1205 C. The steel is strong at temperature and less forgiving than a standard austenitic, so reheats, die temperature and reduction per pass are planned to hold the finishing temperature.

Solution annealing

From 1150 C minimum, water quenched, to restore the fully austenitic structure and return nitrogen and molybdenum to solution.

Sigma phase

Precipitation can occur roughly between 700 and 900 C. Time in that band during forging, straightening and welding is held to the minimum the process allows.

Welding

Nickel-base filler metals such as Alloy 625, so the weld metal is not less corrosion resistant than the parent material.

Melting route

EF and LF with vacuum oxygen decarburisation for nitrogen and carbon control. ESR remelted material where the specification or the end user calls for it.

Inspection

Ultrasonic examination to EN 10228-3, SEP 1921 or ASTM A388 as specified, with EN 10204 3.1 certification or third party 3.2.

07

Product forms and size envelope

Forged product forms in 1.4652 / S32654
Product formTypical use
Seamless rolled ringsPressure vessel and heat exchanger shell courses, girth rings, retaining rings
Forged ringsSections and alloys outside the ring-mill envelope, upset and punched
Flanges, blinds, hubsSeawater, firewater and subsea pipework, risers and manifolds
Round bars, hollow barsMachined valve stems, spindles, fasteners, pump shafts
Shafts and spindlesPumps, agitators and compressors in chloride or acid duty
Discs, tube sheets, coversShell and tube heat exchangers, brine heaters, condensers, valve discs
Sleeves, bushings, bodiesValve bodies and seat rings for ball, gate, globe, check and plug valves
Nozzles, manifolds, blocksPressure parts, subsea connector bodies, custom machined components
Plant limits at Jiangyin Jiangnan Metal
DimensionLimitSet by
Rolled ring ODup to 6,000 mm6 m radial-axial ring mill
Machined disc diameterup to 5,000 mm5,000 mm vertical turning lathe
Shaft turned lengthup to 14,000 mmC61160 horizontal lathe, 15 m well furnace for vertical quench
Bored cylinders1,600 mm dia x 10,000 mmCNC deep-hole drilling machine
Single-piece weightup to 30,000 kg60 t maximum heat, 6,300 t press
Minimum order10 kg, no minimum piece countWorks policy
Lead time20 to 60 daysRoute and heat treatment cycle

These are plant limits across all grades. For 1.4652 the practical ceiling is normally set by ingot availability rather than press capacity, so the achievable size is confirmed against the drawing at enquiry.

08

Applications

Seawater desalination

Brine heater internals, high pressure brine recirculation piping, high pressure RO components and seawater piping in MSF and MED plants.

Offshore oil and gas

Seawater, firewater and subsea pipework with the associated risers, manifolds, pressure vessels, valves and heat exchangers, and produced-water handling.

Chemical process plant

Equipment exposed to sulphuric acid, organic acids and mixed chloride bearing acids in the higher pressure and temperature ranges.

Chlor-alkali and ClO2

Process piping, heat exchanger parts and valve components where oxidising conditions and high chloride levels occur together.

Power and FGD

Flue gas desulphurisation systems and waste incineration plant handling acidic chloride condensates.

Pulp and paper

Black liquor evaporator components in kraft mills, where alkaline chloride conditions crack lower alloyed steels.

Quotation

Send the drawing or the finished dimensions, the quantity, the governing standard, the delivery condition and the NDT and certification level required. Forged weight, machining allowance, heat treatment and test scope are quoted together, so the figure covers a part that can be accepted rather than a billet price.

Jiangyin Jiangnan Metal Co., Ltd.
No.1 Chengxiqiao Road, Zhouzhuang Town
Jiangyin City, Jiangsu Province, China
Tel +86 189 2135 9659
Email sales@steelforgepieces.com

Email your drawing

09

Questions

Is X1CrNiMoCuN24-22-8 the same as 1.4652 and 654 SMO?

Yes. X1CrNiMoCuN24-22-8 is the EN chemical designation and 1.4652 the EN material number for the same steel. UNS S32654, trade name 654 SMO, is the recognised equivalent. Some Chinese tables list S32652 and 015Cr24Ni22Mo8Mn3CuN next to this grade, so confirm the exact specification on the order.

Can 1.4652 rings and flanges be forged to our drawing?

Yes. Rings and flanges are produced as open-die forgings or as seamless rolled rings depending on size and quantity, then solution annealed, machined to the agreed allowance, ultrasonically examined and certified to EN 10204 3.1 or 3.2.

Which welding consumable should be used?

Nickel-base fillers such as Alloy 625, so the weld metal is not the weak point for corrosion. Control heat input and time in the 700 to 900 C range to limit sigma phase.

How does it compare with 254 SMO (1.4547 / A182 F44)?

1.4652 carries 7 to 8 per cent molybdenum and 0.45 to 0.55 per cent nitrogen against the lower molybdenum and nitrogen of 254 SMO, giving higher pitting resistance in hot high-chloride media and a higher proof strength. 254 SMO remains the more economical choice where the service is less severe. See the A182 F44 / 254 SMO forgings page.

What sizes and weights can be supplied?

Plant limits are 6,000 mm outside diameter on the ring mill, 5,000 mm machined diameter, 14,000 mm shaft turning length, 1,600 by 10,000 mm bored, and 30,000 kg single-piece weight. For 1.4652 the ceiling is usually ingot availability, so the size is confirmed against the drawing. Minimum order 10 kg with no minimum piece count, normal lead time 20 to 60 days.

10

Related grades and sources

Enquiries for this grade are commonly compared against A182 F44 (254 SMO / 1.4547), 904L, Sanicro 28, Alloy 24, A182 F53 (2507 duplex), A182 F55, Alloy 31, Incoloy 825 and Hastelloy C-276.

Composition and specified mechanical properties are taken from the EN 10088-3 grade tables, with EN 10088-1, EN 10088-2 and ISO 15510 for designation and listing. Typical physical and mechanical values, the PREN calculation and the hot working and solution annealing ranges follow published mill and materials datasheets for 1.4652 and UNS S32654. Figures are given for reference and do not replace the agreed order specification or the material test certificate issued with the goods. A Markdown version of this page is published at /Stainless-Steel/X1CrNiMoCuN24-22-8.md. Page reviewed 9 October 2026.