Grade data sheet UNS S31009 / 310H  ·  Melted and forged in Jiangyin, Jiangsu, China T +86 189 2135 9659  ·  E sales@steelforgepieces.com
Jiangyin Jiangnan Metal Open-die forgings · Seamless rolled rings · Since 1997 Request quotation

Home / Stainless Steel / UNS S31009

Heat-resisting austenitic stainless steel · 25Cr-20Ni

UNS S31009 forgings Grade 310H to ASTM A182 F310H. Seamless rolled rings, forged rings, flanges, shafts, discs, tube sheets, sleeves and bars.

UNS S31009 is the high-carbon modification of Alloy 310, developed for enhanced creep resistance at elevated temperature. Carbon is controlled to a 0.04 to 0.10 percent band, a specified minimum as well as a maximum, and ASTM A182 calls for a coarse grain size of No. 6 or coarser. The low-carbon counterpart is 310S, UNS S31008, used where fabrication matters more than creep strength.

This works melts its own steel and forges it on the same site, so a finished S31009 part traces back to its melt number rather than to a purchased billet. Orders start at 10 kg with no minimum piece count.

Grade summaryS31009
Designation
310H
UNS
S31009
Forging spec
ASTM A182/A182M F310H
Carbon
0.04 to 0.10 %
Chromium
24.0 to 26.0 %
Nickel
19.0 to 22.0 %
Tensile min
515 MPa / 75 ksi
Yield min
205 MPa / 30 ksi
Elongation min
30 %
Grain size
ASTM No. 6 or coarser
Condition
Solution treated and quenched
Certification
EN 10204 3.1 or 3.2
01

S31009 against 310 and 310S

All three grades share the same 25Cr-20Ni base. Carbon and silicon separate them, and carbon decides whether a part holds its shape under sustained load at temperature.

Carbon and silicon limits in the Alloy 310 family, weight percent, maximum unless a range is shown
GradeUNSCarbonSiliconReason for selection
310S310000.251.50General high-temperature corrosion resistance
310SS310080.081.50Low-carbon version, used for ease of fabrication and better weldability
310HS310090.04 to 0.100.75High-carbon modification for enhanced creep resistance

Because the carbon ranges overlap, the grain size and carbon content of a given lot can often satisfy both the 310S and the 310H requirements at once, which is why dual-certified 310S/310H material is common on the market. Dual certification is a property of the actual heat and not a general equivalence. Where creep strength governs the design, order S31009 by name and call for the grain size and carbon results on the certificate.

02

Chemical composition

UNS S31009 composition, weight percent
ElementASTM A182 F310H, forgings310H per A240 and published data sheets
Carbon, C0.04 to 0.100.040 to 0.10
Chromium, Cr24.0 to 26.024 to 26
Nickel, Ni19.0 to 22.019 to 22
Manganese, Mn2.00 max2.00 max
Silicon, Si1.00 max0.75 max
Phosphorus, P0.045 max0.045 max
Sulfur, S0.030 max0.030 max
Iron, FeBalanceBalance, about 45.9 to 49.1
Silicon limit differs by product form

The 0.75 percent silicon figure in general circulation comes from plate data sheets. For forgings ordered to A182 F310H the limit is 1.00 percent maximum. State which limit your specification imposes at enquiry stage, since it affects heat selection.

Clause 8.2 of A182 prohibits grades to which lead, selenium or other elements have been added to render the material free-machining. Clause 8.3 prohibits starting material produced to a specification that requires any element beyond those listed for the grade. Material is purchased and melted on that basis.

03

Mechanical properties

The A182 minima are the acceptance criteria. Published typical values vary between sources and are listed separately for orientation only.

ASTM A182/A182M F310H, required room-temperature minima
PropertyMetricInch-pound
Tensile strength, min515 MPa75 ksi
Yield strength, min205 MPa30 ksi
Elongation in 50 mm or 4D, min30 %30 %
Reduction of area, min50 %50 %
Brinell hardnessNot specified by A182 for this grade
Published typical values, two sources, not acceptance criteria
PropertySandmeyer Steel, typical at 20 CAZoM, annealed 310H
Tensile strength550 MPa / 80 000 psi515 MPa / 74 700 psi
Yield strength, 0.2 % offset245 MPa / 35 000 psi205 MPa / 29 700 psi
Elongation45 % min in 2 in.40 % in 50 mm
Hardness217 Brinell max217 Brinell / 95 HRB
Modulus of elasticity196 GPa / 28.5 x 106 psi200 GPa / 29 000 ksi
Shear modulusNot stated77.0 GPa / 11 200 ksi
Poisson's ratioNot stated0.3

One tension test is made for each heat of austenitic grades. Specimens are not removed until all heat treatment is complete, and for austenitic and ferritic-austenitic grades the specimen may be taken from any convenient location. Where test blanks are used they receive approximately the same working as the finished product, are heat treated with it, and approximate its maximum cross section.

04

Physical properties

Physical properties of the Alloy 310 / 310S / 310H family
PropertyValue
Density7.89 g/cm3 / 0.285 lb/in3
Melting range1354 to 1402 C / 2470 to 2555 F
Specific heat, 0 to 100 C502 J/kg·K / 0.12 BTU/lb·F
Thermal conductivity at 100 C10.8 W/m·K / 8.0 BTU/hr/ft2/ft/F
Electrical resistivity at 20 C78.0 microhm·cm
Modulus of elasticity196 GPa / 28.5 x 106 psi
05

Creep and creep rupture

Creep performance is the reason the H grade exists. Typical published values for Alloy 310, in MPa.

Typical creep strain and creep rupture stress, MPa
TemperatureCreep strainCreep rupture
1 000 h10 000 h100 000 h1 000 h10 000 h100 000 h
600 C / 1112 F1201004020014080
700 C / 1292 F503520804520
800 C / 1472 F2010835208
900 C / 1652 F106315105
1000 C / 1832 F531.5942

These figures suit preliminary sizing. Code-qualified allowable stresses for S31009 must be taken from ASME Boiler and Pressure Vessel Code Section II, Part D at the design temperature.

06

Service temperature limits

Published limits differ because sources assume different atmospheres and different definitions of continuous service. Both commonly cited sets are reproduced rather than averaged.

Reported maximum service temperatures for Alloy 310 and 310H
ConditionLimitSource
Oxidation resistance, mildly cyclic conditions1100 C / 2010 FSandmeyer Steel
Oxidizing, sulfur up to 2 g/m3, continuous1050 C / 1922 FSandmeyer Steel
Oxidizing, sulfur up to 2 g/m3, peak1100 C / 2012 FSandmeyer Steel
Oxidizing, sulfur above 2 g/m3950 C / 1742 FSandmeyer Steel
Low oxygen atmosphere, sulfur up to 2 g/m31000 C / 1832 FSandmeyer Steel
Nitriding or carburizing atmosphere850 to 950 C / 1562 to 1742 FSandmeyer Steel
310H, intermittent service1040 C / 1904 FAZoM
310H, continuous service1150 C / 2102 FAZoM
Cryogenic use, low magnetic permeability and toughnessdown to -268 C / -450 FSandmeyer Steel
Two ranges to design around

AZoM advises against continuous service between 425 and 860 C, 797 to 1580 F, because of carbide precipitation. Separately, Alloy 310 is subject to sigma phase precipitation when held between 650 and 950 C, 1202 to 1742 F, and a solution annealing treatment at 1100 to 1150 C, 2012 to 2102 F, will restore a degree of toughness. Frequent thermal cycling also reduces oxidation resistance.

07

Corrosion behaviour

Alloy 310 is not designed for service in wet corrosive environments. The high carbon content present to enhance creep properties has a detrimental effect on aqueous corrosion resistance, and the alloy is prone to intergranular corrosion after long-term exposure at high temperature. Set against that, its 25 percent chromium content makes it more corrosion resistant than most heat-resisting alloys.

At temperature the high chromium and silicon content give resistance to sulfidation, and the alloy can be used in moderately carburizing atmospheres. More severe carburizing atmospheres in thermal process equipment usually call for a nickel alloy such as Alloy 330, UNS N08330. In reducing, nitriding or carburizing atmospheres 310H does not perform as well as Alloy 600, UNS N06600 or Alloy 800, UNS N08800, though it does outperform most heat-resisting stainless steels in those conditions.

Where the duty is wet and aggressive rather than hot, 904L, Sanicro 28 or Hastelloy C-276 are the more suitable forging grades.

08

Melting and forging

Melting

Clause 6.2 of A182 requires stainless steels to be melted by electric furnace, with the option of separate degassing and refining, by vacuum furnace, or by either of those followed by vacuum or electroslag consumable remelting. Clause 6.3 requires sufficient discard to secure freedom from injurious piping and undue segregation.

This plant covers those routes in house. S31009 runs through the 25 t electric arc furnace, is refined in a 25 t or 50 t ladle furnace and decarburised under vacuum in the 30 t or 60 t VOD units where low carbon or tight nitrogen control is wanted. Maximum heat size is 60 tonnes. Protective-atmosphere electroslag remelting at 3 t and 6 t, and vacuum arc remelting at 6 t, are available where a specification or a heavy section calls for a remelted ingot.

Forging

Material is forged as close as practicable to the specified shape and size, with uniform heating at 950 to 1200 C. Two restrictions in A182 bear directly on how S31009 piping components may be made. Clause 6.4.1 states that flanges of any type, elbows, return bends, tees and header tees shall not be machined directly from bar stock. Clause 6.4.2 permits cylindrically shaped parts to be machined from forged or rolled solution-annealed austenitic stainless steel bar without additional hot working. A quotation for bar-machined 310H flanges does not meet the specification.

Clause 1.2 limits products made to A182 to a maximum weight of 10 000 lb, 4540 kg, and refers larger austenitic products to A965/A965M. Both specifications are quoted here.

09

Heat treatment

Solution annealing requirements for grade F310H
RequirementValueClause
Heat treat typeSolution treat and quenchA182 Table 1
Solutioning temperature, minimum1900 F [1040 C]A182 Table 1
Cooling mediaLiquidA182 Table 1
Quenching, cool below500 F [260 C]A182 Table 1
Cooling after hot working, before heat treatingBelow 1000 F [538 C]A182 7.1
Direct quench from hot-working heatNot permitted for F310HA182 7.3.1
Grain sizeASTM No. 6 or coarser, per E112A182 10.1.1
No direct quench for this grade

Clause 7.3.1 allows many austenitic grades to be individually rapidly quenched immediately after hot working while still above the minimum solution annealing temperature. F310H is named in the list of grades excluded from that option, together with F304H, F309H, F310, F316H, F321, F321H, F347, F347H, F348, F348H, F45 and F56. Every S31009 forging therefore receives a separate solution anneal and liquid quench with a recorded furnace chart.

Solution annealing above the 1040 C minimum is carried out in the three high-temperature car-bottom furnaces on site, working chamber 3,500 x 1,300 x 1,100 mm. Long shafts are quenched vertically in the two 15 m well-type furnaces. After hot forming, a final anneal at 1000 to 1150 C followed by rapid quenching is the recommended practice for this alloy family. Heat treatment of forgings may be performed before machining.

10

Forming and welding

The alloy is quite ductile and cold forms in a manner very similar to 316. Cold forming of pieces that will see long-term exposure to high temperature is not recommended, since the alloy is subject to carbide precipitation and sigma phase precipitates.

Alloy 310 can be readily welded by most standard processes, including TIG, plasma, MIG, SMAW, SAW and FCAW. Where the best corrosion resistance after welding is required, the low-carbon 310S variant is preferred to minimise carbide precipitation, which is a further reason to settle early whether the application is creep driven or fabrication driven.

11

Testing and certification

Ultrasonic examination follows EN 10228-4, the part of the standard covering ultrasonic testing of austenitic and austenitic-ferritic stainless steel forgings. EN 10228-3 applies to ferritic and martensitic forgings and is not the correct part for this grade. ASTM A388/A388M, referenced by A182, is available as an alternative acceptance basis, as is SEP 1921 where a customer specification calls for it.

On-site testing covers optical emission spectrometry to ASTM E415, infrared carbon and sulphur analysis to ASTM E1019, handheld positive material identification, tensile testing on 600 kN and 300 kN machines to ASTM A370, Charpy V-notch impact to minus 60 C, ultrasonic flaw detection, and metallographic grain size measurement to ASTM E112, which is the method the A182 grain size requirement calls for.

Intergranular corrosion testing to ASTM A262 or ASTM G28 is placed with an accredited third-party laboratory and the report is issued alongside the mill certificate. Other supplementary requirements of A182 can be added to the order, among them liquid penetrant examination to E165 and macroetch testing to E340. Magnetic particle examination is not applicable to this grade, which is non-magnetic in the solution annealed condition.

Inspection documents are issued to EN 10204 Type 3.1, validated by an inspection representative independent of the manufacturing department and reporting results on the specific heat, or to Type 3.2, witnessed by BV, DNV, LR, SGS, TUV or the customer's own inspector. Nominate the inspection body on the purchase order. The works holds CCS, BV, DNV, LR and NK approvals.

12

Parts produced in S31009

Seamless rolled rings

Ring-rolled from a punched preform on the radial-axial mills, rectangular or contoured section, to OD 6,000 mm.

Forged rings

Upset and punched rings for sections outside the ring-mill envelope, retaining rings and valve seat rings.

Flanges

Weld neck, blind, slip-on, socket weld, lap joint, orifice and long weld neck to ASME B16.5 and B16.47, or to drawing.

Shafts and spindles

Stepped, eccentric and crankshaft forgings, furnace fan and roller shafts, to 14,000 mm turned length.

Discs and tube sheets

Solid forged discs, tube sheets and covers, supplied proof-machined for volumetric inspection.

Sleeves and bushings

Bored hollow sections, liners and couplings, bored from solid forged blanks.

Bars and blocks

Forged round, flat and square bar and blocks, the feedstock route for machined bodies and tooling.

Valve and pressure parts

Valve bodies, bonnets, stems, seat rings, blocks, nozzles and manifolds, with heavy-wall pipe sections.

13

Plant capacity

Melting, forging, ring rolling, heat treatment, machining and inspection are all on one site. No forging, heat treatment or machining step is subcontracted.

Working envelope and the equipment that sets each limit
ProductLimitSet by
Seamless rolled ringsup to OD 6,000 mm6 m radial-axial ring mill, with 3 m and 1 m mills for smaller sizes
Minimum ring sizefrom OD 50 mmUpset-and-punch route below ring-mill range
Forged shaftsup to 14,000 mm turned lengthC61160 horizontal lathe, 15 m well furnace for vertical quench
Discs, tube sheets, blocksup to 5,000 mm machined diameter5,000 mm vertical turning lathe
Bored cylinders and hollow shaftsup to 1,600 mm dia x 10,000 mmCNC deep-hole drilling machine
Single-piece weightup to 30,000 kg60 t heat size, 6,300 t press
Minimum order10 kg, no minimum piece countWorks policy
Lead time20 to 60 daysWorks policy

Presses are 6,300 t, 4,000 t and 2,000 t, with hammers at 5 t, 3 t, 2 t, 1 t and 750 kg for drawing out and small batch work. Heat treatment runs across 14 furnaces, including three high-temperature car-bottom furnaces and two well-type furnaces 15,000 mm deep by 1,500 mm diameter.

14

Applications

Where Alloy 310 and 310H components are used
SectorComponents
FurnacesBurners, doors, fans, piping, recuperators
Fluidized bed furnacesCoal combustors, grids, piping, wind boxes
Ore processing and steel plantsSmelter and steel melting equipment, continuous casting equipment
Petroleum refiningCatalytic recovery systems, flares, recuperators, tube hangers
Power generationCoal gasifier internals, pulverized coal burners, tube hangers
Sintering and cement plantsBurners, burner shields, feeding and discharging systems, wind boxes
Thermal processingAnnealing covers and boxes, burner grids, doors, fans, muffles and retorts, recuperators, walking beams
Food processingEquipment handling hot organic acids
CryogenicCryogenic components and structures
15

Equivalent designations

Cross-reference. Equivalences between systems are close but rarely exact.
SystemDesignationNote
UNSS31009Exact
AISI and common usage310HExact
ASTM and ASME, forgingsA182/A182M F310H, SA-182 F310H, A965/A965MGoverning specifications for forged parts
ASTM, plateA240 310H, SA240, AMS 5521Plate product forms
Werkstoff number1.4845Listed for the 310 / 310S / 310H family, corresponds most closely to 310S, not an exact S31009 equivalent
JISSUS310SEquivalent to the low-carbon grade, approximate only
Related gradesS31000, S31008, N08330Select by carbon level and atmosphere

Other heat-resisting and high-temperature forging grades produced here: 347H, F321 and 321H, F347, 330, A286, Incoloy 800H, 800HT, Inconel 617, Haynes 230 and Hastelloy X.

16

Questions and answers

Is UNS S31009 the low-carbon or the high-carbon version of Alloy 310?

High carbon. S31009, designated 310H, is the high-carbon modification developed for enhanced creep resistance, with carbon between 0.04 and 0.10 percent. The low-carbon version is 310S, S31008, at 0.08 percent maximum, used for ease of fabrication. Plain 310, S31000, permits up to 0.25 percent carbon.

What heat treatment does ASTM A182 F310H require?

Solution treat and quench. Table 1 of A182 gives a minimum solutioning temperature of 1900 F [1040 C], liquid cooling media, and quenching to below 500 F [260 C]. Clause 7.1 requires cooling below 1000 F [538 C] after hot working before heat treating.

Can F310H be quenched straight from the forging heat?

No. Clause 7.3.1 offers that route to many austenitic grades but names F310H among the exclusions, alongside F304H, F309H, F310, F316H, F321, F321H, F347, F347H, F348, F348H, F45 and F56. A separate solution anneal and liquid quench is required.

What grain size must F310H forgings have, and why?

ASTM No. 6 or coarser, determined to Test Methods E112. Grades F304H, F309H, F310H and F316H all carry this requirement. Coarse grain reduces the grain-boundary area available for creep deformation, which is the purpose of an H grade.

Can 310H flanges be machined from round bar?

No. Clause 6.4.1 prohibits machining flanges of any type, elbows, return bends, tees and header tees directly from bar stock. Cylindrically shaped parts may be machined from forged or rolled solution-annealed austenitic bar without additional hot working, but flanges must be forged.

How heavy a single S31009 forging can be supplied?

A182 itself caps products at 10 000 lb, 4540 kg, and refers heavier austenitic parts to A965/A965M. Plant capacity reaches 30,000 kg on a single piece, set by the 60 t heat size and the 6,300 t press, with rings to OD 6,000 mm and shafts to 14,000 mm turned length.

Is 310H suitable for wet or aqueous corrosive service?

It is not designed for it. The high carbon that gives the grade its creep strength is detrimental to aqueous corrosion resistance, and the alloy becomes prone to intergranular corrosion after prolonged high-temperature exposure. For wet corrosive duty, 904L, Sanicro 28 or a nickel alloy such as Hastelloy C-276 is the better choice.

Which temperature ranges should be avoided?

Two. Continuous service between 425 and 860 C is not advised because of carbide precipitation. Sigma phase precipitates on holding between 650 and 950 C, and a solution anneal at 1100 to 1150 C restores a degree of toughness. Frequent thermal cycling also reduces oxidation resistance.

Can S31009 be dual-certified as 310S?

Frequently, yes, since the carbon range and grain size of a given lot can satisfy both sets of requirements at once. That is a property of the heat rather than a general equivalence. Where creep strength governs, order S31009 and require carbon and grain size results on the certificate.

What ultrasonic standard and certification come with the forgings?

Ultrasonic testing to EN 10228-4, the part covering austenitic and austenitic-ferritic stainless forgings, with ASTM A388/A388M or SEP 1921 as alternatives. Inspection documents to EN 10204 Type 3.1, or Type 3.2 witnessed by BV, DNV, LR, SGS, TUV or your own inspector. A262 or G28 intergranular corrosion testing is placed with an accredited third-party laboratory.

17

Sources

  1. ASTM A182/A182M, Standard Specification for Forged or Rolled Alloy and Stainless Steel Pipe Flanges, Forged Fittings, and Valves and Parts for High-Temperature Service. Clause 1.2 scope and weight limit, 6.2 melting, 6.3 discard, 6.4.1 and 6.4.2 bar stock, 7.1 and Table 1 heat treatment, 7.3.1 exclusions, 8.2 free-machining prohibition, 9.2 to 9.5 testing, 10.1.1 grain size.
  2. ASTM A965/A965M, Specification for Steel Forgings, Austenitic, for Pressure and High Temperature Parts, referenced by A182 clause 1.2 for austenitic products above the A182 weight limit.
  3. Sandmeyer Steel Company, 310/310S/310H specification sheet. Grade distinctions, composition, physical properties, creep data, service temperature limits, wet and high-temperature corrosion, hot and cold forming, welding.
  4. Ferrobend, ASTM A182 F310H data sheet. F310H composition limits and mechanical property minima.
  5. AZoM, Stainless Steel Grade 310H, UNS S31009. Composition, annealed mechanical properties, intermittent and continuous service temperatures, carbide precipitation range.
  6. EN 10228-4, Non-destructive testing of steel forgings, Part 4, Ultrasonic testing of austenitic and austenitic-ferritic stainless steel forgings.
  7. EN 10204, Metallic products, Types of inspection documents. Type 3.1 and Type 3.2.

Data on this page is compiled from the standards and published data sheets listed above and is given for information. It is not a guarantee and not an express or implied warranty of suitability for any application. Material selection and code allowable stresses remain the responsibility of the purchaser's design engineer. Page last reviewed 5 October 2026.

Request a quotation

Send a drawing, or the outside diameter, inside diameter, height and quantity. State the governing specification, A182 F310H or A965 F310H, the delivery condition, the certificate type, EN 10204 3.1 or 3.2, and any ultrasonic acceptance class, and the price will be firm rather than indicative. Minimum order 10 kg with no minimum piece count. Lead time 20 to 60 days.

Company
Jiangyin Jiangnan Metal Co., Ltd.
Integrated melting works and open-die forge
Address
No.1 Chengxiqiao Road, Zhouzhuang Town,
Jiangyin City, Jiangsu Province, China
Telephone, WhatsApp, WeChat
+86 189 2135 9659
Email
sales@steelforgepieces.com
Business hours
Monday to Saturday, 08:00 to 17:30
China Standard Time, UTC+8