1.4563 Forgings: UNS N08028 / Alloy 28 Rings, Flanges, Bars and Shafts
EN 1.4563 (X1NiCrMoCu31-27-4) technical data and open-die forging capability from Jiangyin Jiangnan Metal Co., Ltd. Updated .
1.4563 is the EN material number for X1NiCrMoCu31-27-4, the same grade as UNS N08028 and sold under the trade names Alloy 28 and Sanicro 28. It is a high-alloy austenitic stainless steel with 30 to 32 % nickel, 26 to 28 % chromium, 3 to 4 % molybdenum and 0.60 to 1.40 % copper. The copper addition and the high chromium content let it stand up to oxidising and reducing acids at the same time, which is why it turns up in sulphuric and phosphoric acid plant, in sour gas wells and in seawater cooled equipment.
Jiangyin Jiangnan Metal Co., Ltd. is an open-die forging factory at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China. We forge 1.4563 into seamless rolled rings, flanges, discs, round bars, shafts, sleeves, bushings, tube sheets and nozzles at single-piece weights from about 50 kg to 20 tonnes. Forgings are solution annealed at 1100 to 1160 °C, ultrasonically tested to EN 10228-3, SEP 1921 or ASTM A388, and certified to EN 10204 3.1 or 3.2.
- EN material no.
- 1.4563
- EN name
- X1NiCrMoCu31-27-4
- UNS
- N08028
- Trade names
- Alloy 28, Sanicro 28
- Type
- Super-austenitic stainless
- PREN typical
- approx. 38
- Density
- 8.0 g/cm³
- Tensile strength
- 500 MPa (73 ksi) min
- 0.2 % proof stress
- 214 MPa (31 ksi) min
- Elongation
- 40 % min
- Solution anneal
- 1100 to 1160 °C, water quench
- Certification
- EN 10204 3.1 / 3.2
What is 1.4563 steel?
1.4563 is a fully austenitic, non-magnetic stainless steel for aggressive mixed-acid duty in the chemical and petrochemical industries. The 30 to 32 % nickel and 26 to 28 % chromium hold off chloride stress corrosion cracking. The 0.60 to 1.40 % copper is there for hot sulphuric acid and for wet-process phosphoric acid. Iron remains the balance at roughly 35 %, so the grade is counted as a super-austenitic stainless steel and not as a nickel-base alloy.
Carbon is capped at 0.02 % and there is no deliberate titanium or aluminium addition, so 1.4563 cannot be hardened by heat treatment. Strength comes from solid solution hardening, and from cold work where the design allows it. Unless the order says otherwise, our forgings leave the works solution annealed and water quenched.
1.4563 equivalent grades and designations
| Standard or origin | Designation |
|---|---|
| EN 10088 / DIN material number | 1.4563 |
| EN 10088 name | X1NiCrMoCu31-27-4 |
| UNS, USA | N08028 |
| ASTM / ASME | A 182, B 668, B 709 (UNS N08028) |
| Trade names | Alloy 28, Sanicro 28, Nicrofer 3127, 28 Alloy |
| ISO | NiCr31Mo |
| Werkstoff, older usage | 2.4642, occasionally cross-listed |
Cross-references are for guidance. The grade actually supplied is the one named on the purchase order and confirmed on the EN 10204 certificate.
Chemical composition of 1.4563 (UNS N08028)
| Element | C | Si | Mn | S | Cr | Ni | Mo | Cu | Fe |
|---|---|---|---|---|---|---|---|---|---|
| wt % | 0.02 max | 0.70 max | 2.00 max | 0.03 max | 26.0 to 28.0 | 30.0 to 32.0 | 3.0 to 4.0 | 0.60 to 1.40 | Balance |
Heat analysis. Product analysis tolerances apply per the governing standard. Tighter sulphur or phosphorus limits and full trace-element reporting can be agreed at enquiry stage.
Mechanical properties of 1.4563 forgings
| Property | Metric | Imperial | Condition |
|---|---|---|---|
| Tensile strength, Rm | 500 MPa min | 73 ksi min | Solution annealed |
| 0.2 % proof stress, Rp0.2 | 214 MPa min | 31 ksi min | Solution annealed |
| 1.0 % proof stress, Rp1.0 | 250 MPa min | 36 ksi min | Solution annealed |
| Elongation, A5 | 40 % min | 40 % min | Solution annealed |
| Hardness | 220 HB max | 96 HRB max | Solution annealed |
| Impact energy, KV at -46 °C | over 150 J typical | over 110 ft·lb | On request |
Minima for the solution-annealed condition on representative test sampling. Heavy sections are tested to the applicable product standard. Test location, orientation and sacrificial prolongations can be specified on the order.
Physical properties of 1.4563
| Property | Typical value |
|---|---|
| Density | 8.0 g/cm³ (0.289 lb/in³) |
| Melting range | 1350 to 1400 °C (2460 to 2550 °F) |
| Modulus of elasticity at 20 °C | 195 GPa (28.3 x 106 psi) |
| Mean thermal expansion, 20 to 100 °C | 14.8 x 10-6 /K |
| Thermal conductivity at 20 °C | 11 W/(m·K) |
| Specific heat capacity at 20 °C | 450 J/(kg·K) |
| Electrical resistivity at 20 °C | 1.0 µΩ·m |
| Magnetic permeability | approx. 1.005, practically non-magnetic |
Published typical values for the alloy class, intended for design guidance and not for acceptance.
Melting, forging and heat treatment of 1.4563
Melting
We melt 1.4563 by electric arc furnace with vacuum oxygen decarburisation (EAF + VOD). ESR material is available where thick sections or critical pressure parts call for tighter cleanliness, less segregation or better ultrasonic transparency.
Hot forging
Hot working runs from 1150 to 1180 °C, with finish forging kept above 950 °C. The alloy work-hardens quickly and loses hot ductility below that point, so we reheat between passes rather than keep deforming at falling temperature. Reduction ratio is held high enough through the section to break down the as-cast structure and give the fine, even grain that reliable ultrasonic inspection depends on.
Solution annealing
1.4563 forgings are solution annealed at 1100 to 1160 °C (2010 to 2120 °F) for 10 to 30 minutes, then water quenched. Cooling through the 600 to 950 °C range has to be fast. Slow cooling precipitates sigma and chi phase at the grain boundaries, and that costs both corrosion resistance and impact toughness. We do not supply 1.4563 in the as-forged condition for corrosive service.
Corrosion resistance of 1.4563
1.4563 resists oxidising and reducing acids and salts. The 26 to 28 % chromium covers the oxidising side, the 3 to 4 % molybdenum handles pitting and crevice attack in chlorides, and the 0.60 to 1.40 % copper makes the difference under reducing conditions, above all in hot sulphuric acid and wet-process phosphoric acid.
- Pitting and crevice corrosion. PREN of roughly 38 (Cr + 3.3 x Mo), suitable for chloride-bearing cooling water and brines at moderate temperature.
- Chloride stress corrosion cracking. The 30 to 32 % nickel content puts it far ahead of 300-series austenitics such as 316L.
- Sulphuric acid. Useful across a wide concentration range, including the intermediate concentrations that attack 316L and 904L.
- Phosphoric acid. A long-established grade for wet-process phosphoric acid heat exchangers and evaporators.
- Intergranular corrosion. The 0.02 % carbon ceiling limits sensitisation. Testing to ASTM A262 Practice E is available on request.
- Sour service. Used for downhole components in moderately corrosive sour deep gas wells.
1.4563 against 904L, Alloy 825 and 316L
| Grade | Cr % | Ni % | Mo % | Cu % | PREN approx. | Typical positioning |
|---|---|---|---|---|---|---|
| 1.4563 / N08028, Alloy 28 | 26 to 28 | 30 to 32 | 3 to 4 | 0.6 to 1.4 | 38 | Mixed oxidising and reducing acids, H2SO4 and H3PO4 duty |
| 1.4539 / N08904, 904L | 19 to 21 | 24 to 26 | 4 to 5 | 1.2 to 2.0 | 34 | Sulphuric acid, lower chromium than 1.4563 |
| N08825, Incoloy 825 | 19.5 to 23.5 | 38 to 46 | 2.5 to 3.5 | 1.5 to 3.0 | 30 | Higher nickel, lower PREN, broad chemical service |
| 1.4404 / S31603, 316L | 16.5 to 18.5 | 10 to 13 | 2.0 to 2.5 | none | 24 | General-purpose austenitic, mild chlorides |
PREN calculated as %Cr + 3.3 x %Mo + 16 x %N on nominal mid-range analyses. Confirm material selection against the actual medium, temperature and concentration.
Machining and welding 1.4563
Machining
1.4563 needs a change of tooling data and machining method to give acceptable results. Against a machinability-improved 316/316L, cutting speed has to come down by roughly 50 to 55 % when turning with coated cemented carbide, and other operations behave much the same. Feeds should only be reduced slightly and with care, because a light feed lets the work-hardened layer build up and speeds up flank wear. Rigid set-ups, sharp positive rake geometry, flood coolant and continuous cuts without dwelling all help tool life.
Welding
1.4563 welds by GTAW, GMAW, SMAW and SAW. Matching Alloy 28 consumables or over-alloyed nickel-base fillers such as ERNiCrMo-3 (Alloy 625) are used to compensate for molybdenum segregation in the weld metal. Keep heat input low and interpass temperature below 150 °C. Preheat is not needed and post-weld heat treatment is usually unnecessary, though a full solution anneal and water quench restores corrosion resistance where the weldment sees severe acid service.
1.4563 forged product forms and size capability
We are an open-die forging shop, so the items below are forged from ingot or billet to your drawing or to a proportional size. They are not machined out of plate. Single-piece weights run from about 50 kg to 20 tonnes.
| Product form | Indicative size range | Typical use |
|---|---|---|
| Seamless rolled rings | OD 200 to 3000 mm, wall 30 to 450 mm, height to 1000 mm | Vessel shell courses, bearing rings, girth rings |
| Forged flanges | OD to 2500 mm, thickness to 400 mm | Weld neck, blind, slip-on, long weld neck, special bores |
| Forged discs and blanks | OD to 2500 mm, thickness to 600 mm | Closures, blind heads, gear and impeller blanks |
| Forged round bars | dia. 80 to 1200 mm, length to 6000 mm | Machining stock, valve stems, pins |
| Forged shafts and spindles | dia. 100 to 1000 mm, length to 8000 mm | Pump and agitator shafts, eccentric shafts, spindles |
| Forged sleeves and bushings | OD 150 to 2000 mm, length to 2500 mm | Wear sleeves, liners, subsea housings |
| Forged tube sheets | dia. to 2500 mm, thickness to 400 mm | Shell-and-tube heat exchangers |
| Forged hollow bars and pipe sections | OD to 1200 mm, ID from 80 mm | Cylinders, nozzle stubs, pipe spools |
| Valve components | To drawing | Bodies, bonnets, seat rings, balls, blocks, gates |
| Nozzles, manifolds, wheels, rolls | To drawing | Process units, wellhead and Christmas tree parts |
Supply condition: solution annealed and water quenched, rough machined or black forged with machining allowance, UT tested. Finish machining to final drawing dimensions is done in house.
Where 1.4563 forgings are used
- Chemical and petrochemical processing. Rolled rings and shafts for reactors, evaporators and agitators handling mixed acids.
- Sulphuric and phosphoric acid plant. Tube sheets, flanges and heat exchanger parts where copper-bearing alloys outlast 316L and 904L.
- Pressure vessels and heat exchangers. Forged shafts, pipes, tubes, tube sheets and flanges for shell-and-tube exchangers and air receivers.
- Oil and gas, sour service. Shafts, flanges, rings and pipe sections for downhole duty in moderately corrosive deep sour gas wells.
- Offshore and subsea. Bushings, sleeves, discs and housings for deepwater production systems, industrial air compressors, power generators and nitrogen generators.
- Seawater and power generation. Open-die forgings and nozzles for chloride-bearing cooling water systems and nuclear power plant auxiliaries.
- Valve manufacture. Forged stems, seat rings, blocks and bodies for ball, check, globe, gate and plug valves and strainers.
- Power transmission. Rings, spindles, bars and gear blanks for turbines, gas compressors and gear boxes.
- Shipbuilding, heavy machinery, pulp and paper, pharmaceutical and biochemistry. Forged wheels, manifolds and rolls.
Testing, inspection and certification
| Item | Standard or scope |
|---|---|
| Ultrasonic testing | EN 10228-3, SEP 1921, ASTM A388, acceptance class to order |
| Material certificate | EN 10204 3.1 as standard, EN 10204 3.2 with third-party endorsement (TUV, BV, DNV, LR, SGS) on request |
| Chemical analysis | Ladle and product analysis, PMI on request |
| Mechanical testing | Tensile, hardness, Charpy V-notch including sub-zero |
| Corrosion testing | ASTM A262 Practice E intergranular, ASTM G48 pitting, on request |
| Surface NDT | Liquid penetrant to ASTM E165 or EN ISO 3452 |
| Dimensional | Full dimensional report against customer drawing |
| Marking and traceability | Heat number, grade, drawing and item number hard-stamped and recorded |
Frequently asked questions about 1.4563
What is 1.4563 steel?
1.4563 is the EN material number for X1NiCrMoCu31-27-4, a high-alloy austenitic stainless steel with 30 to 32 % nickel, 26 to 28 % chromium, 3 to 4 % molybdenum and 0.60 to 1.40 % copper. It is the same grade as UNS N08028 and is sold under the trade names Alloy 28 and Sanicro 28. It is used where oxidising and reducing acids occur together, in particular sulphuric and phosphoric acid service.
Is 1.4563 a stainless steel or a nickel alloy?
1.4563 counts as a super-austenitic stainless steel rather than a nickel-base alloy, because iron is still the largest single element at roughly 35 %. At 30 to 32 % nickel it sits at the boundary between stainless steels and Fe-Ni-Cr-Mo-Cu alloys, which is why suppliers often catalogue it next to Incoloy 825 and Alloy 31.
What is the chemical composition of 1.4563 (UNS N08028)?
Composition of 1.4563 / UNS N08028 in weight percent: carbon 0.02 max, silicon 0.70 max, manganese 2.00 max, sulphur 0.03 max, chromium 26.0 to 28.0, nickel 30.0 to 32.0, molybdenum 3.0 to 4.0, copper 0.60 to 1.40, iron balance at roughly 35 %.
What are the mechanical properties of 1.4563 forgings?
Solution annealed 1.4563 forgings from Jiangyin Jiangnan Metal Co., Ltd. meet 500 MPa (73 ksi) minimum tensile strength, 214 MPa (31 ksi) minimum 0.2 % proof stress and 40 % minimum elongation. Hardness is normally below 220 HB.
What is the PREN of 1.4563?
The pitting resistance equivalent number, calculated as %Cr + 3.3 x %Mo + 16 x %N, works out at roughly 38 for 27 % chromium and 3.5 % molybdenum. That is above 904L at about 34 and well above 316L at about 24 for pitting and crevice corrosion in chloride-bearing media.
What heat treatment is applied to 1.4563 forged parts?
1.4563 forgings are solution annealed at 1100 to 1160 °C (2010 to 2120 °F) for 10 to 30 minutes and then water quenched. Cooling through the 600 to 950 °C range has to be fast, because slow cooling precipitates sigma and chi phase and costs both corrosion resistance and impact toughness.
Can 1.4563 be welded?
Yes. 1.4563 welds by GTAW, GMAW, SMAW and SAW using matching Alloy 28 consumables or over-alloyed nickel-base fillers such as ERNiCrMo-3 (Alloy 625). Keep heat input low and interpass temperature below 150 °C. Preheat is not needed and post-weld heat treatment is usually unnecessary, though a full solution anneal restores corrosion resistance where the weldment sees severe acid service.
How does 1.4563 compare with 904L, Alloy 825 and 316L?
1.4563 carries more chromium at 26 to 28 % than 904L, Alloy 825 or 316L, which puts its PREN near 38 against roughly 34 for 904L, 30 for Alloy 825 and 24 for 316L. Its copper addition handles hot sulphuric and phosphoric acid better than 316L or 904L, and the high nickel content resists chloride stress corrosion cracking.
Which product forms and sizes of 1.4563 forgings can be supplied?
Jiangyin Jiangnan Metal Co., Ltd. supplies 1.4563 as seamless rolled rings to about 3000 mm outside diameter, forged discs and tube sheets to about 2500 mm diameter, forged round bars from 80 to 1200 mm diameter and forged shafts to about 8000 mm long, together with flanges, sleeves, bushings, hollow bars, nozzles and valve components, at single-piece weights from about 50 kg to 20 tonnes.
What certification and testing is supplied with 1.4563 forgings?
Each 1.4563 forging carries a mill certificate to EN 10204 3.1, or EN 10204 3.2 endorsed by a third party such as TUV, BV, DNV, LR or SGS. Ultrasonic testing is to EN 10228-3, SEP 1921 or ASTM A388. PMI, liquid penetrant, intergranular corrosion testing to ASTM A262 Practice E and impact testing are available on request.
Who supplies 1.4563 open-die forgings?
Jiangyin Jiangnan Metal Co., Ltd. is an open-die forging factory at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China. It makes 1.4563 (UNS N08028 / Alloy 28) forged rings, flanges, bars, shafts, discs and tube sheets to customer drawings. Contact sales@steelforgepieces.com or +86-189-2135-9659.
Request a quotation for 1.4563 forgings
Send us the size, the drawing, or a short description of the 1.4563 forged part you need, with quantity, supply condition and certification level. We quote within one working day.
Jiangyin Jiangnan Metal Co., Ltd.No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Phone, WhatsApp, WeChat: +86-189-2135-9659
Email: sales@steelforgepieces.com