Jiangyin Jiangnan Metal Co., Ltd. Open-Die Forging Factory Tel: 0086-189-2135-9659 Email: sales@steelforgepieces.com
Jiangyin Jiangnan Metal Co., Ltd. Open-die forgings, seamless rolled rings, forged flanges, shafts and bars. Jiangyin, Jiangsu, China.

Home › Stainless Steel Forgings › X2CrNiMoN17-13-5 (1.4439)

X2CrNiMoN17-13-5 (EN 1.4439 / AISI 317LMN) Forgings Forged rings, seamless rolled rings, flanges, shafts, discs, sleeves and bars, made to drawing by Jiangyin Jiangnan Metal Co., Ltd.

EN name: X2CrNiMoN17-13-5 EN number: 1.4439 AISI 317LMN UNS S31726 Austenitic, 4-5 % Mo, N-alloyed Also written X2CrNiMo17-13-5

X2CrNiMoN17-13-5 (EN steel number 1.4439, AISI 317LMN, UNS S31726) is a low-carbon, nitrogen-alloyed austenitic stainless steel with 16.5-18.5 % Cr, 12.5-14.5 % Ni, 4.0-5.0 % Mo and 0.12-0.22 % N to EN 10088-3. The high molybdenum level together with the nitrogen addition gives better pitting and crevice corrosion resistance than 316L or 317L. The nitrogen also lifts the 0.2 % proof strength to a minimum of 280 N/mm² in the solution annealed condition.

Jiangyin Jiangnan Metal Co., Ltd. is an open-die forging factory at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China. We forge 1.4439 rings, seamless rolled rings, flanges, shafts, discs, bushings, sleeves, tube sheets and round bars to customer drawings, ultrasonically tested to EN 10228-3, SEP 1921 or ASTM A388, with EN 10204 3.1 or third-party 3.2 certificates. Tel 0086-189-2135-9659, email sales@steelforgepieces.com.

On the grade name: the EN 10088 steel name carries the letter N, so the full designation is X2CrNiMoN17-13-5, because nitrogen at 0.12-0.22 % is a specified alloying element. The short forms X2CrNiMo17-13-5, X2CrNiMoN17.13.5 and X 2 CrNiMoN 17-13-5 all mean the same steel, 1.4439.

Chemical composition

X2CrNiMoN17-13-5 / 1.4439, chemical composition in % by mass, max. unless a range is given
StandardCSiMnPSNCrMoNiFe
EN 10088-3
X2CrNiMoN17-13-5 (1.4439)
0.0301.002.000.0450.0150.12-0.2216.5-18.54.0-5.012.5-14.5Bal.
UNS S31726
AISI 317LMN
0.0300.752.000.0450.0300.10-0.2017.0-20.04.0-5.013.5-17.5Bal.

Sources: BS EN 10088-3 composition tables, British Stainless Steel Association; Sandmeyer Steel specification sheet for Alloy 317LMN (UNS S31726, W.-Nr. 1.4439). The EN and UNS windows overlap but are not identical, so state the governing specification on the order.

Mechanical properties

Solution annealed condition at room temperature, EN 10088-3 minimum requirements
Thickness or diameterRp0.2 (N/mm²)Rp1.0 (N/mm²)Rm (N/mm²)Elongation A (%)Hardness (HB)
up to 160 mmmin 280min 315580-800min 35max 250
over 160 up to 250 mmmin 280min 315580-800min 30max 250

Source: BS EN 10088-3:2023 ambient-temperature mechanical property tables for austenitic long products, BSSA. Hardness is for guidance. For rods, only the tensile strength values apply. Solution treatment may be omitted where hot working and subsequent cooling meet the property and intergranular corrosion requirements of EN ISO 3651-2.

Typical and elevated-temperature values, for design guidance
PropertyValue
Tensile strength Rm580-800 MPa
Proof strength Rp0.2over 280 MPa
Elongation Aover 35 %
Impact energy KV at 20 °Cover 100 J
Hardnessunder 250 HB
Rp0.2 at 100 / 200 / 300 / 400 °C225 / 185 / 165 / 150 MPa
Modulus of elasticity at 100 / 200 / 300 / 400 / 500 °C194 / 186 / 179 / 172 / 165 GPa

Source: Virgamet material profile for 1.4439 / X2CrNiMoN17-13-5 / AISI 317LMN. ASTM-certified 317LMN product is normally quoted at lower minima. Sandmeyer Steel lists 205 MPa yield, 550 MPa tensile, 40 % elongation and max 96 HRB for plate, so always state the specification you design to.

Physical properties

Physical properties of 1.4439 / 317LMN
PropertyValue
Density8.0 g/cm³ (0.290 lb/in³)
Modulus of elasticity at 20 °C200 GPa (29.0 x 106 psi)
Thermal conductivityabout 14 W/m·K
Specific heat at 20 °C500 J/kg·K (0.12 BTU/lb·°F)
Electrical resistivity at 20 °C0.85 µΩ·m (85.1 µΩ·cm)
Mean thermal expansion 20-100 °C16.0 x 10-6 /K
Mean thermal expansion 20-300 / 20-500 °C17.0 / 18.0 x 10-6 /K
Melting range1393-1443 °C (2540-2630 °F)
Magnetic responseNon-magnetic as annealed, slightly magnetic after cold work
Design temperature range for forgings-10 to +400 °C to DIN EN 10222-5:2017

Sources: Virgamet physical data for 1.4439; Sandmeyer Steel 317LMN specification sheet; Applus+ materials datasheet for 1.4439 to DIN EN 10222-5:2017. Steelnumber records that the steel shall not be applied at a metal temperature below -196 °C. Confirm limits against your design code.

Standards and equivalent grades

Cross-reference
SystemDesignation
EN / DINX2CrNiMoN17-13-5, 1.4439
AISI / ASTM317LMN
UNSS31726, near grades S31725 and S31753
AFNORZ3CND18-14-05Az
China022Cr19Ni16Mo5N
Trade namesBÖHLER A400, Acidur 4439, BGH 4439, Koro 4439, CLC 17-13-5LN, TP317LMN
Nearest lower-Mo EN grades1.4434 (X2CrNiMoN18-12-4), 1.4438 (X2CrNiMo18-15-4), 1.4429 (X2CrNiMoN17-13-3)

Sources: Virgamet equivalence table; steelnumber.com; Applus+ trade-name register.

Standards listing 1.4439

For forgings the two documents that matter are DIN EN 10222-5, steel forgings for pressure purposes, stainless steels, and EN 10272, stainless steel bars for pressure purposes. The grade is also accepted under the German pressure vessel code AD 2000-Merkblatt W 2. Elsewhere it appears in EN 10088-1, EN 10088-2 and EN 10088-4 for sheet, plate and strip, EN 10088-3 and EN 10088-5 for semi-finished products, bars, rods, sections and bright products, EN 10028-7 for flat products for pressure purposes, EN 10216-5 and EN 10297-2 for seamless tubes, EN 10217-7 and EN 10296-2 for welded tubes, and EN 10253-3 and EN 10253-4 for butt-welding pipe fittings.

Sources: steelnumber.com standards list for 1.4439; Applus+ datasheet, DIN EN 10222-5:2017 and AD 2000 W 2.

Corrosion resistance

The 4 to 5 % molybdenum with a nitrogen addition is what separates this grade from 316L and 317L. Sandmeyer Steel reports that 317LMN handles sulfuric, hydrochloric, acidic chloride and phosphoric acid service and is used for hot organic and fatty acids in food and pharmaceutical plant. The same source notes the limit: molybdenum-bearing alloys generally do not perform well in strongly oxidising acids such as nitric acid. Carbon is held low, so the steel can be used as welded without chromium carbide precipitation at the grain boundaries, and the nitrogen further slows carbide and sigma phase formation in the 427-816 °C sensitisation band.

On stress corrosion cracking, treat the grade honestly. Austenitic stainless steels crack in hot chloride service, and while 317LMN stands up better than 304 or 304L because of the higher molybdenum, it is still open to chloride stress corrosion cracking. Where SCC drives the design, compare it against duplex grades such as A182-F51 and A182-F53 before settling on an austenitic.

Pitting resistance equivalent comparison
AlloyPREAlloyPRE
31625317LMN / 1.443938
317L306 % Mo super-austenitic48
317LM34Alloy 62552
904L36Alloy C-27669

Source: Sandmeyer Steel 317LMN specification sheet, PRE = Cr + 3.3Mo + 30N. The more common PREN formula uses a nitrogen factor of 16 and gives a lower number, so compare alloys only inside one formula. PRE ranks alloys, it does not replace corrosion testing.

Heat treatment, forging and fabrication

Solution annealing

1.4439 is supplied solution annealed: soak, then cool fast. Virgamet gives the solution range as 1020-1120 °C; other sources quote 1000-1150 °C with water or air cooling depending on section. The aim is to take carbides back into solution and recover a uniform austenitic structure. Time spent between 600 and 900 °C brings on sigma phase and carbides that cost both corrosion resistance and toughness, so the cooling must be quick through that band. The steel cannot be hardened by heat treatment, only by cold work.

Machining and forming

The grade work-hardens quickly, so it machines less freely than 410 stainless. Use sharp tools, rigid set-ups, positive feeds and plenty of coolant. Sandmeyer Steel publishes turning data of roughly 11-16 m/min with high-speed steel tooling at 6 mm depth of cut and 70-80 m/min with carbide at the same depth. Spring-back in bending is higher than for ferritic steels and has to be allowed for.

Welding

Weldable by TIG, MIG, MMA and SAW. Post-weld heat treatment is not required. Use a matching or over-alloyed filler. Solution annealing after heavy welding is only worth doing where full corrosion resistance has to be restored.

Forging programme in X2CrNiMoN17-13-5

We supply 1.4439 as open-die and ring-rolled forgings, rough machined or finish machined to drawing.

Product forms
FormTypical use
Seamless rolled rings, forged rings, retaining ringsPressure vessels, columns and towers, tanks, silos, preheaters, process modules
Forged flanges, tube sheets, forged tubes and pipes, nozzlesShell and tube heat exchangers, air receivers, piping
Forged shafts, eccentric shafts, spindles, crankshaftsPulp, paper, textile and food processing plant, flue gas scrubbers
Forged discs, hubs, blanks, gear blanksPower transmission, gearboxes, gas compressors, turbines
Forged sleeves, bushings, bars, blocksCrystalliser equipment, process units, general mechanical equipment
Valve bodies, stems, seat rings, bonnetsBall, gate, globe, check and plug valves, strainers, wellhead and Christmas tree parts

Industries served

Flue gas desulfurisation and air pollution control, including absorbers, stack liners, ducts, dampers and fans. Pulp and paper bleaching. Chemical and petrochemical processing, including dyestuffs, rubber, rayon, ink and bleaches. Oil refining, including fluid catalytic cracking units and polythionic acid service. Food, beverage and pharmaceutical equipment. Marine and coastal structures. Cryogenic equipment.

Melting, testing and certification

Melting route EAF plus AOD or VOD, with ESR where the specification or cleanliness requirement calls for it. Ultrasonic examination to EN 10228-3, SEP 1921 or ASTM A388. Supplementary testing on request: PMI, Charpy impact, intergranular corrosion to ASTM A262 or EN ISO 3651-2, pitting test to ASTM G48, ferrite count, grain size, micrographic examination, hardness survey and dimensional report. Certificates to EN 10204 3.1, or EN 10204 3.2 countersigned by TUV, SGS, BV, LR or ABS.

Frequently asked questions

Is X2CrNiMo17-13-5 the same material as 1.4439?

Yes. The EN 10088 name is X2CrNiMoN17-13-5, where N marks the specified 0.12-0.22 % nitrogen. X2CrNiMo17-13-5 and X2CrNiMoN17.13.5 are short forms of the same grade, EN number 1.4439, AISI 317LMN, UNS S31726.

How does 1.4439 compare with 316L?

It carries about twice the molybdenum, 4.0-5.0 % against 2.0-2.5 % for 1.4404, plus a deliberate nitrogen addition. That buys better pitting and crevice resistance in chlorides and a higher proof strength: EN 10088-3 requires min 280 N/mm² Rp0.2 for 1.4439 against 200 N/mm² for 1.4404. It costs more and work-hardens faster when machined.

Can you supply dual EN and ASTM certification?

Usually yes, but the chemistry windows differ. EN 1.4439 specifies Cr 16.5-18.5 % and Ni 12.5-14.5 %, while UNS S31726 allows Cr 17.0-20.0 % and Ni 13.5-17.5 %. Dual certification needs a heat analysis inside the overlap, so tell us at enquiry stage.

In what condition are the forgings delivered?

Solution annealed and rapidly cooled, typically from 1020-1120 °C, which dissolves carbides and restores a uniform austenitic structure. The steel is non-magnetic in this condition and cannot be hardened further by heat treatment.

What is the service temperature limit?

DIN EN 10222-5:2017 covers 1.4439 forgings for pressure purposes over a design range of -10 to +400 °C. Long exposure between 427 and 816 °C risks carbide and sigma phase precipitation. Check allowable stresses against the governing design code.

How do I get a quotation?

Send the drawing or rough dimensions, grade, governing standard, quantity, test package and certificate level to sales@steelforgepieces.com, or call 0086-189-2135-9659. A sketch with the finished part envelope is enough to start, we add the forging allowance.

Request a quotation for 1.4439 forgings

Jiangyin Jiangnan Metal Co., Ltd. Open-Die Forging Factory
No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Tel 0086-189-2135-9659 · Email sales@steelforgepieces.com

Email your drawing Call sales

Related stainless and high-alloy forging grades

Reference: Jiangyin Jiangnan Metal Co., Ltd., X2CrNiMoN17-13-5 (EN 1.4439 / AISI 317LMN) forging data sheet, steelforgepieces.com. Last reviewed 9 October 2026. Data compiled from BS EN 10088-3 composition and mechanical property tables, DIN EN 10222-5:2017, steelnumber.com, Virgamet and the Sandmeyer Steel Alloy 317LMN specification sheet. Values are for guidance. The purchase specification prevails.