X2CrNiMo17-12-2 (EN 1.4404 / AISI 316L) Open-Die Forgings
Also written X2CrNiMo17.12.2. Steel number 1.4404, UNS S31603, AISI 316L, BS 316S11, AFNOR Z3CND17-12-02, JIS SUS316L, SS 2348, UNE F.3533.
Grade summary
X2CrNiMo17-12-2 is the EN designation for stainless steel 1.4404, a low-carbon molybdenum-bearing austenitic grade equivalent to AISI 316L and UNS S31603. The 2 to 2.5 % molybdenum addition raises resistance to pitting and chloride attack above that of 304-type steels, and the carbon ceiling of 0.030 % gives resistance to intergranular corrosion in the as-welded condition without stabilising elements.
Jiangyin Jiangnan Metal Co., Ltd., an open-die forging factory at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China, forges this grade into rings, seamless rolled rings, flanges, round bars, discs, sleeves, bushings, shafts, tube sheets and forged pipes to customer drawings. Material is melted by EAF + VOD or ESR, solution annealed, ultrasonically tested to EN 10228-4 and certified to EN 10204 3.1 or 3.2. Enquiries: +86-189-2135-9659, sales@steelforgepieces.com.
- EN steel number1.4404
- UNS / AISIS31603 / 316L
- StructureAustenitic
- Density8.00 kg/dm3
- Solution anneal1030-1110 °C
- Hardnessmax 215 HB
Chemical composition of X2CrNiMo17-12-2 (1.4404)
The limits below are the EN 10088-3 analysis for semi-finished products, bars, rods and sections, which is the composition normally applied to forged bar and open-die forgings in this grade.
| C | Si | Mn | P | S | Cr | Ni | Mo | N |
|---|---|---|---|---|---|---|---|---|
| max 0.030 | max 1.00 | max 2.00 | max 0.045 | max 0.030 | 16.5-18.5 | 10.0-13.0 | 2.00-2.50 | max 0.10 |
Source: EN 10088-3 analysis for 1.4404. Sheet and strip supplied to EN 10088-2 with ASME SA240 316/316L dual certification is often held to tighter limits, typically Si max 0.75 % and S max 0.015 %. State the governing specification on the enquiry and the heat will be selected to suit the tighter window.
Mechanical properties
Values apply in the solution annealed condition. Two sets are given because forgings in this grade are ordered either to European or to ASTM and ASME rules, and the acceptance values differ.
| Thickness | Rp0.2 (MPa) | Rp1.0 (MPa) | Rm (MPa) | Elongation A (%) | Hardness (HB) |
|---|---|---|---|---|---|
| up to 160 mm | 200 | 235 | 500-700 | 40 | max 215 |
| over 160 up to 250 mm | 200 | 235 | 500-700 | 30 | max 215 |
Source: BS EN 10088-3:2023 tensile property table for austenitic standard grades, as summarised by the British Stainless Steel Association. Hardness is given for guidance in the standard.
| Tensile strength | Yield strength, 0.2 % offset | Elongation in 50 mm or 4D | Hardness |
|---|---|---|---|
| 485 MPa (70 ksi) | 170 MPa (25 ksi) | 30 % | max 217 HB |
Source: ASTM A182 acceptance values for grade F316L.
Physical properties at 20 °C
| Property | Value |
|---|---|
| Density | 8.00 kg/dm3 |
| Modulus of elasticity | 200 GPa |
| Thermal conductivity | 15.0 W/(m·K) |
| Specific heat capacity | 0.50 J/(g·K) |
| Electrical resistivity | 0.73-0.75 Ω·mm2/m |
| Mean coefficient of thermal expansion | 16.0 x 10-6/K at 20-100 °C; 17.5 x 10-6/K at 20-400 °C; 18.0 x 10-6/K at 20-500 °C |
| Microstructure | Austenitic, polishable |
Source: EN 10088-based material data sheets for 1.4404. Resistivity is quoted as 0.73 in one sheet and 0.75 in another, both within normal scatter for the grade.
Production route for X2CrNiMo17-12-2 forgings
Melting
Heats are produced by electric arc furnace with VOD refining, or by electro-slag remelting where a cleaner and more homogeneous ingot is needed for heavy sections, pressure parts or sour service. ESR is the usual choice when the finished part is thick-walled and will be volumetrically inspected to a tight acceptance class.
Forging
Open-die forging on hydraulic presses, with ring rolling for seamless rolled rings. The grade forges well. Reduction ratios are planned so that the centre of the section is genuinely worked rather than only upset, which is what gives forged 316L its advantage over cast material or parts machined from bar in pressure-retaining service.
Heat treatment
Solution annealing at approximately 1030 to 1110 °C followed by rapid cooling in water or air. Rapid cooling through the sensitisation range keeps chromium carbides in solution. Because carbon is capped at 0.030 %, the grade also resists intergranular attack after welding, verified where required by EN ISO 3651-2 or ASTM A262 Practice E.
Testing and certification
Ultrasonic examination to EN 10228-4, the part of that series covering austenitic and austenitic-ferritic stainless steel forgings. ASTM A388 is used where an ASTM procedure is called for. Liquid penetrant, PMI, intergranular corrosion testing, impact testing and hardness survey are available on request. Certificates are issued to EN 10204 3.1, or 3.2 with third-party witness such as TUV, BV, LR, DNV or ABS.
Applicable standards
| Standard | Scope |
|---|---|
| EN 10250-4 | Open die steel forgings for general engineering purposes, stainless steels |
| EN 10222-5 | Steel forgings for pressure purposes, martensitic, austenitic and austenitic-ferritic stainless steels |
| EN 10088-1, -2, -3 | List of stainless steels; sheet, plate and strip; semi-finished products, bars, rods, wire and sections |
| EN 10272 | Stainless steel bars for pressure purposes |
| EN 10269 | Steels and nickel alloys for fasteners with specified elevated or low temperature properties |
| ASTM and ASME A182 (F316L), A276, A479 | Forged fittings, flanges and valve parts; stainless bars and shapes |
| AD 2000 W2 and W10 | German pressure vessel material rules |
| NACE MR0175 and ISO 15156-3 | Materials for H2S-containing oil and gas production environments |
| EN 10228-4, ASTM A388 | Ultrasonic testing of austenitic stainless steel forgings |
| EN ISO 3651-2, ASTM A262 Practice E | Resistance to intergranular corrosion |
| EN 10204 3.1 and 3.2 | Types of inspection document for metallic products |
Forged product forms in X2CrNiMo17-12-2
- Forged and seamless rolled ringsRing-rolled to near-net section for vessel shells, bearing races, swivel and turret rings.
- Forged flangesWeld neck, slip-on, blind, long weld neck, orifice and special-bore flanges to ASME B16.5, B16.47 or drawing.
- Forged round bars and shaftsPump shafts, agitator shafts, eccentric shafts, spindles and valve stems.
- Forged discs and disksBlanks for tube sheets, closures, valve bodies and gear blanks.
- Forged sleeves and bushingsHollow forgings bored from solid for pumps, compressors and subsea hardware.
- Forged tubes and pipesThick-wall hollows and forged nozzles where seamless pipe sizes are unavailable.
- Forged tube sheetsHeat exchanger tube sheets, drilled and grooved to specification.
- Valve componentsBodies, bonnets, seat rings, stems and blocks for ball, gate, globe, check and plug valves.
See also the general pages for forged round bars, forged pipes and forged products.
Typical applications
Molybdenum-enhanced corrosion resistance, good weldability and a wide usable temperature range make 1.4404 one of the most widely specified forging grades in process industry. Published application areas for the grade include the chemical and petrochemical industries, food production, pharmaceutical manufacture, mechanical and plant engineering, construction, energy technology, offshore technology, aviation, automotive, electrical equipment, medical technology and valve construction.
Customers order this grade most often for pressure vessel and heat exchanger internals, piping systems and flange sets, pulp and paper digester and liquor tank hardware, brine and process water handling equipment, subsea and deepwater production hardware, compressor and nitrogen generator components, food and pharmaceutical process equipment, and valve trim and bodies.
When another grade suits better
1.4404 is not a universal answer. In warm high-chloride or seawater service its pitting resistance is limited next to 6 % molybdenum or duplex grades, and buyers move to A182 F44, 904L or a duplex such as F51 or F53. Where higher strength is needed at comparable corrosion resistance, the nitrogen-alloyed and duplex grades carry roughly double the proof strength. For continuous service at furnace temperatures the heat-resistant grade X15CrNiSi25-20 (1.4841, AISI 314) is used instead, since it is scaling resistant to around 1150 °C. Send the service conditions with the enquiry and the grade can be reviewed before the order is placed.
Frequently asked questions
What is X2CrNiMo17-12-2 equivalent to?
It is EN steel number 1.4404, equivalent to AISI 316L and UNS S31603, and corresponding to BS 316S11, AFNOR Z3CND17-12-02, JIS SUS316L, SS 2348 and UNE F.3533. Forgings are frequently ordered dual-certified as 1.4404 together with ASTM A182 F316L.
What is the difference between 1.4404 and 1.4401, or 316L and 316?
Both are molybdenum-bearing austenitic grades with essentially the same EN mechanical minimums, Rp0.2 of 200 MPa and tensile of 500 to 700 MPa up to 160 mm thickness. The difference is carbon. 1.4404 is the low-carbon variant, which is why it is preferred for welded fabrications where sensitisation and later intergranular corrosion are a concern.
Can X2CrNiMo17-12-2 forgings be welded?
Yes. The grade welds well by gas-shielded, arc and resistance welding, and the low carbon content means resistance to intergranular corrosion is retained as welded, without post-weld solution annealing in most applications. Supplier data sheets describe autogenous or gas fusion welding as limited.
Which ultrasonic testing standard applies?
EN 10228-4, which covers ultrasonic testing of austenitic and austenitic-ferritic stainless steel forgings. EN 10228-3 is the ferritic and martensitic part of the same series and does not apply to 1.4404, although it is often mis-cited for stainless. ASTM A388 is used where the order calls for an ASTM procedure.
What sizes can be forged?
Size is limited by press and ring mill capacity and by the finished geometry, so quotations are made against a drawing or a sketch giving outside diameter, inside diameter, height or length, and the machining allowance to be left on. With the drawing and the governing specification you will receive a weight, a lead time and a price.
What certificates are issued?
EN 10204 3.1 as standard, or EN 10204 3.2 with a third-party inspection body witnessing the tests. Chemical analysis, tensile results, hardness, heat treatment records, NDT reports and heat traceability are included.
Request a quotation
A quotation needs the grade and governing specification, the drawing or rough dimensions with machining allowance, the quantity, the heat treatment and test requirements, and the certificate type. Send those details to sales@steelforgepieces.com and a price normally follows within one working day.
Technical data compiled from EN 10088-3, EN 10250-4, EN 10222-5, ASTM A182 and published 1.4404 material data sheets. Figures are for guidance and are not a guarantee of properties. The governing purchase specification always takes precedence. Page reviewed and updated 9 October 2026 by the technical sales team of Jiangyin Jiangnan Metal Co., Ltd.