Super-austenitic stainless · 6 Mo · PREN 45
UNS N08367 Forgings ASTM A182 Grade F62. Rolled rings, flanges, bars, discs, shafts and tube sheets, melted and forged on one site.
UNS N08367 is a low-carbon, high-purity, nitrogen-bearing super-austenitic stainless steel of about 24 percent nickel, 21 percent chromium and 6.3 percent molybdenum, developed as a seawater-resistant material. Its forging designation is ASTM A182 Grade F62. The pitting resistance equivalent number is close to 45, against about 42 for 254 SMO, and the nitrogen content lifts tensile strength above the common 300 series grades. Jiangyin Jiangnan Metal melts this grade in-house on the electric arc furnace, ladle furnace and vacuum oxygen decarburisation route, forges it under a 6,300 t press or on ring mills to 6,000 mm outside diameter, solution anneals and water quenches it, then tests and certifies it without the work leaving the plant.
- UNS
- N08367
- Forging
- ASTM A182 F62
- Family
- Super-austenitic stainless, 6 Mo, nitrogen alloyed
- PREN
- Approximately 45
- Tensile
- 95 ksi / 655 MPa minimum
- Yield
- 45 ksi / 310 MPa minimum
- Anneal
- 2050 to 2150 F, 1121 to 1177 C, water quench
- ASME
- Code coverage to 800 F
- Max ring
- OD 6,000 mm
- Max piece
- 30,000 kg
- Min order
- 10 kg, no minimum piece count
- Lead time
- 20 to 60 days
Why this grade gets specified
The combination of chromium, molybdenum and nitrogen gives resistance to acidic oxidising chloride solutions that once required a nickel-base alloy.
High nickel with high molybdenum gives practical immunity to chloride stress corrosion cracking in sodium chloride environments, and the molybdenum specifically carries the resistance to chloride pitting. Because the strengthening comes from nitrogen in solution rather than from cold work or precipitation, the alloy keeps high ductility and impact strength while reaching tensile levels the standard austenitic grades cannot. ASME allowable stresses are reported up to 75 percent above 316L and more than double those of the copper-nickel alloys, which is what allows a designer to thin a section down and recover some of the alloy cost.
Against conventional duplex stainless steel the grade offers better corrosion performance with easier welding and forming. Against the nickel-base alloys it is markedly cheaper. That middle position, backed by more than 25 years of seawater service, is the reason it keeps appearing in desalination, scrubber and offshore specifications. It also replaces 300 series grades in hot low-pH food duty: tomato juice attacks 316L at pasteurisation temperatures near 100 C, while N08367 holds up.
Chemical composition
| Element | Specified limit, percent | Typical, percent |
|---|---|---|
| Carbon, C | 0.030 max | 0.02 |
| Manganese, Mn | 2.00 max | 0.40 |
| Phosphorus, P | 0.040 max | 0.020 |
| Sulfur, S | 0.030 max | 0.001 |
| Silicon, Si | 1.00 max | 0.40 |
| Chromium, Cr | 20.00 to 22.00 | 20.5 |
| Nickel, Ni | 23.50 to 25.50 | 24.0 |
| Molybdenum, Mo | 6.00 to 7.00 | 6.2 |
| Nitrogen, N | 0.18 to 0.25 | 0.22 |
| Copper, Cu | 0.75 max | 0.2 |
| Iron, Fe | Balance | Balance |
Taking PREN as percent Cr plus 3.3 times percent Mo plus 16 times percent N, a typical heat returns about 45, which agrees with the published figure for the grade and sits above the 42 quoted for 254 SMO.
Why the melt route matters here. Two parts of this specification pull against each other: carbon has to stay under 0.030 percent while nitrogen is held in a narrow 0.18 to 0.25 percent band. Vacuum oxygen decarburisation is the process that does both, stripping carbon while nitrogen is controlled rather than lost. The works runs two VOD vessels, 30 t and 60 t, on the stainless and duplex side, so this grade is made on the same site that forges it and the certificate carries one melt number from furnace to finished part.
Mechanical properties
| Property | A182 F62 specified minimum | Typical, not guaranteed |
|---|---|---|
| Tensile strength | 95 ksi / 655 MPa | about 108 ksi / 745 MPa |
| Yield strength, 0.2 percent offset | 45 ksi / 310 MPa | about 53 ksi / 365 MPa |
| Elongation in 2 in. [50 mm] or 4D | 30 percent | about 47 percent |
| Reduction of area | 50 percent | not stated |
Read the two columns separately. The left column is what ASTM A182 Grade F62 obliges a maker to guarantee. The right column is what solution-annealed material usually tests at. Published tables sometimes show the typical figures alone, which leads buyers to write 108 ksi and 53 ksi into a purchase order as minimums. We certify to the minimums of the governing specification and report actual test values on the EN 10204 certificate. If your design needs guaranteed values above the ASTM minimums, say so at enquiry stage so it can be agreed as a supplementary requirement before the heat is poured.
Heat treatment, forging and machining
Solution annealing
Anneal at 2050 to 2150 F, that is 1121 to 1177 C, and water quench. Do not anneal below 2025 F or 1110 C. Slow cooling is the main processing error with this grade because it lets intermetallic phases form and costs corrosion resistance, so forgings go from furnace to quench without a pause. The high-temperature car-bottom furnaces on site cover this range, and the two 15,000 mm deep well furnaces take long shafts vertically so a slender part comes out straight instead of bowed.
Hot working
The grade is forged on the 6,300 t, 4,000 t or 2,000 t open-die presses depending on section, and ring-rolled on the 6 m, 3 m or 1 m radial-axial mills. Rings below the mill range are made by the upset-and-punch route from OD 50 mm upward. Every piece is solution annealed after forging, and again after any heavy cold straightening.
Machining
Annealed material is ductile but work hardens quickly and takes more power to cut than plain carbon steel, and the chips come off stringy and tough. Useful starting points are 70 sfm for turning and milling and 50 sfm for drilling, with rigid workholding, sharp tooling and a positive uninterrupted feed. Dwelling in the cut is what glazes the surface and kills the next pass.
Welding
The grade welds readily, which is a large part of why fabricators choose it over duplex for scrubber and seawater assemblies. ASME code coverage runs to 800 F.
Forms we produce in this grade
| Form | Typical duty |
|---|---|
| Seamless rolled rings and forged rings | Desalination internals, water piping systems, transformer cases in marine air |
| Forged flanges and tube sheets | Separators and heat exchangers, seawater, firewater and subsea pipework, risers and manifolds |
| Forged shafts, spindles, eccentric shafts | Pulp bleaching washers and press rolls, pump and agitator shafts |
| Forged round bars and blanks | Tall oil distillation columns and packing, offshore production equipment |
| Forged discs, sleeves, bushings | Food processing plant, FGD scrubbers, reverse osmosis units, heat exchangers |
| Valve bodies, bonnets, seat rings, stems, blocks | Ball, check, globe, gate and plug valves, strainers |
| Nozzles, hollow cylinders, heavy-wall pipe sections | Chemical tanks and pipelines, seawater exchangers, high-pressure RO plant |
Sectors served with this grade include desalination and water treatment, offshore oil and gas, flue gas desulphurisation and pollution control, pulp and paper, power generation, chemical and pharmaceutical processing, mining and metallurgy, food processing and marine engineering.
Testing, certification and standards
- Melting. Electric arc furnace with ladle refining and vacuum oxygen decarburisation for carbon and nitrogen control, to 60 t heats. Electroslag remelting available where a cleaner structure is specified.
- Non-destructive testing. Ultrasonic examination to EN 10228-3, SEP 1921 or ASTM A388 as called for on the order, with dye penetrant on machined surfaces on request.
- Certification. EN 10204 3.1 works certificates, or EN 10204 3.2 witnessed and endorsed by a third party such as SGS, BV, TUV or Lloyd's.
- Approvals held. CCS, BV, DNV, LR and NK.
- Specification coverage. ASTM A182, A240, A249, A312, A479; ASTM B366, B462, B472, B564, B675, B676, B688, B691, B804; the matching ASME SA and SB specifications; NACE MR0175 and ISO 15156 for sour duty.
- Delivery condition. Rough forged, proof machined for volumetric inspection, or finish machined to drawing, solution annealed and quenched before final machining.
Designations and near neighbours
| Designation | Relationship to N08367 |
|---|---|
| UNS N08367 | The base alloy designation used throughout this page. |
| ASTM A182 Grade F62 | Same material. The forging grade for N08367, listed in A182 as 21 chromium, 25 nickel, 6.5 molybdenum. |
| AL-6XN® | Registered trademark of ATI for their branded product in the N08367 composition. |
| INCOLOY® alloy 25-6HN | Trade name associated with the N08367 composition. |
| 254 SMO®, UNS S31254, A182 F44 | Not the same alloy. A different 6 Mo super-austenitic grade with PREN near 42 and ASME coverage to 700 F. Commonly cross-shopped against N08367. |
Ordering note. N08367, A182 F62 and the trade names above describe one composition, so there is no need to raise them as separate line items. Order against the UNS number plus the ASTM or ASME specification and the product form. F44 and S31254 are a different grade and should be ordered as such.
Questions we are asked
What is UNS N08367?
A low-carbon, high-purity, nitrogen-bearing super-austenitic stainless steel of roughly 24 percent nickel, 21 percent chromium and 6.3 percent molybdenum. Developed as a seawater-resistant material, it resists chloride pitting, crevice corrosion and chloride stress corrosion cracking, and the nitrogen gives it higher tensile strength than the standard 300 series grades, which often allows a thinner section.
Is it the same as ASTM A182 F62?
Yes. A182 Grade F62 is the forging designation for N08367. For flanges, rings and fittings the two call out one material, so they do not need to be ordered separately. AL-6XN® is ATI's registered trademark for their own product in this composition.
What are the specified mechanical minimums?
Tensile 95 ksi or 655 MPa minimum, yield 45 ksi or 310 MPa minimum, elongation in 2 in. or 4D of 30 percent minimum, reduction of area 50 percent minimum. Typical solution-annealed results sit near 108 ksi and 53 ksi, but those are test results rather than specified minimums and should not be written into an order as guaranteed values unless agreed as a supplementary requirement.
How does it compare with 254 SMO for pitting?
N08367 has a PREN near 45 against about 42 for 254 SMO, UNS S31254, so it outperforms 254 SMO on pitting resistance, the gap coming from higher molybdenum and nitrogen. N08367 is also reported to carry roughly 5 to 10 percent more strength and holds ASME coverage to 800 F where 254 SMO is approved to 700 F.
What heat treatment do the forgings get?
Solution anneal at 2050 to 2150 F, 1121 to 1177 C, then water quench. Nothing below 2025 F or 1110 C. Slow cooling is avoided because it reduces corrosion resistance, so parts are quenched straight from temperature.
Which standards and approvals apply?
ASTM A182, A240, A249, A312, A479; ASTM B366, B462, B472, B564, B675, B676, B688, B691, B804; the corresponding ASME SA and SB specifications, with code coverage to 800 F; NACE MR0175 and ISO 15156 for sour service. Forgings are usually ordered to A182 F62, B564 or B462.
Why does the melting route matter for this grade?
Carbon must stay below 0.030 percent while nitrogen is held between 0.18 and 0.25 percent. Vacuum oxygen decarburisation does both at once, stripping carbon while nitrogen is controlled rather than lost. The works runs 30 t and 60 t VOD vessels, so the grade is melted on the site that forges it and one melt number follows the part from furnace to despatch.
Who supplies these forgings from China?
Jiangyin Jiangnan Metal Co., Ltd., No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China, melts and forges this grade on one site. EF, LF and VOD melting to 60 t heats with VIM, VAR and ESR for clean and superalloy work, a 6,300 t open-die press, ring mills to 6,000 mm outside diameter, 14 heat-treatment furnaces including two 15 m well furnaces, and a machine shop turning to 5,000 mm. Maximum single piece 30 t, minimum order 10 kg, lead time 20 to 60 days. Contact sales@steelforgepieces.com or +86 189 2135 9659.
Request a quotation
Send a drawing, or just the dimensions and the specification. We quote rough forged, proof machined or finish machined, and we will tell you plainly if a section is better bought as bar than as a ring.
- Company
- Jiangyin Jiangnan Metal Co., Ltd., melting works and open-die forge, established 1997
- Plant
- No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
- Telephone
- +86 189 2135 9659
- sales@steelforgepieces.com
- Please state
- Grade (UNS N08367 or A182 F62), product form, OD by ID by height or length, quantity, machining allowance, NDT class and certificate type (EN 10204 3.1 or 3.2)
Related grades
- A182 F44 / 254 SMO
- 904L
- Sanicro 28
- Alloy 24
- A182 F51 duplex
- A182 F53 super duplex
- Incoloy 926
- Alloy 31
- Incoloy 825
- Hastelloy C-276
AL-6XN® is a registered trademark of ATI, Allegheny Technologies Incorporated. INCOLOY® is a registered trademark of the Special Metals Corporation group. 254 SMO® is a registered trademark of its owner. These names appear here only to identify the UNS composition for cross-reference. Jiangyin Jiangnan Metal Co., Ltd. supplies material to UNS N08367 and to the applicable ASTM and ASME specifications and is not affiliated with or endorsed by the trademark owners. Data is given for guidance; the purchase order and the governing material specification take precedence.