GRADE SUS 890L  /  UNS N08904  /  EN 1.4539 Jiangyin Jiangnan Metal Co., Ltd.  ·  0086-189-2135-9659  ·  sales@steelforgepieces.com
Jiangyin Jiangnan Metal Open-die forgings · Seamless rolled rings · Since 1997

JIS G4303 · G4304 · G4305 — Super austenitic stainless steel

SUS 890L Forgings Rolled rings, flanges, discs, shafts, bars, sleeves and tube sheets, forged and solution treated in Jiangyin, Jiangsu, China.

SUS 890L is the Japanese designation for the alloy sold elsewhere as 904L: a low carbon, copper bearing austenitic stainless steel of roughly 20 % chromium, 25 % nickel, 4.5 % molybdenum and 1.5 % copper. It carries UNS number N08904 and EN number 1.4539. Jiangyin Jiangnan Metal Co., Ltd. forges SUS 890L to drawing as rolled rings, flanges, discs, shafts, sleeves, bushings and tube sheets, with ultrasonic testing to ASTM A388, EN 10228-3 or SEP 1921 and certificates to EN 10204 3.1 or 3.2.

Grade dataSUS 890L
JIS
SUS 890L
UNS
N08904
EN number
1.4539
Structure
Austenitic, non-magnetic
Proof stress
215 N/mm² min
Tensile
490 N/mm² min
Elongation
35 % min
Hardness
90 HRB / 187 HB max
PREN
About 35
01

What SUS 890L is

Carbon is held to 0.02 % maximum, which is low enough that chromium carbides do not form at the grain boundaries during welding, so no stabilising element is needed. The 23 to 28 % nickel is what gives the grade its resistance to chloride stress corrosion cracking. The 1 to 2 % copper is what separates it from 316L: copper is what carries the alloy through sulphuric and other reducing acids, particularly in the awkward mid concentration range.

Japan lists the grade under three product standards. SUS890L appears in JIS G4303 for bars, G4304 for hot rolled plate, sheet and strip, and G4305 for cold rolled plate, sheet and strip. Tube and pipe take their own names, SUS890LTB in JIS G3463 and SUS890LTP in JIS G3459. JIS G4303 also lists SUS317J5L, a second Japanese designation sharing the same international equivalent.

The limits are worth knowing before the grade is specified. In aggressive nitric acid SUS 890L is weaker than molybdenum free grades such as 304L and 310L. It also carries a heavy price, because nickel and molybdenum dominate the cost. Duplex 2205 has taken over a good share of the duties this alloy once held, offering comparable corrosion resistance at higher strength and lower cost, though 2205 is not suited above about 300 °C.

02

Chemical composition

Composition limits for SUS 890L to JIS G4304, weight %, balance iron
LimitCSiMnPSNiCrMoCu
Minimum–––––23.0019.004.001.00
Maximum0.0201.002.000.0450.03028.0023.005.002.00

Nitrogen is named in the JIS element list but carries no numeric limit; commercial heats usually run around 0.10 %. Flat rolled 904L to ASTM B625 allows sulphur to 0.035 % rather than the 0.030 % above, so the JIS limit is the tighter of the two.

03

Mechanical and physical properties

Room temperature mechanical requirements, solution treated
PropertyJIS SUS 890LASTM A182 F904L
0.2 % proof stress, min215 N/mm²215 MPa / 31 ksi
Tensile strength, min490 N/mm²490 MPa / 71 ksi
Elongation, min35 %35 % in 2 in.
Hardness, max90 HRB / 187 HBNot specified; 220 HBW often ordered
Typical physical properties, annealed condition
PropertyValue
Density7 900 kg/m³
Modulus of elasticity190 GPa
Mean thermal expansion, 0–100 °C15 µm/m·°C
Thermal conductivity at 20 °C11.5 W/m·K
Specific heat, 0–100 °C500 J/kg·K
Electrical resistivity952 nΩ·m
Magnetic responseNon-magnetic
Pitting resistance equivalentAbout 35
04

Equivalent designations

Cross reference for SUS 890L. Equivalents are close but rarely identical; the ordering specification governs
SystemDesignation
Japan, barSUS890L and SUS317J5L to JIS G4303
Japan, plate and stripSUS890L to JIS G4304 and JIS G4305
Japan, tube and pipeSUS890LTB to JIS G3463; SUS890LTP to JIS G3459
United StatesAISI 904L; ASTM 904L; forgings to ASTM A182 F904L
UNSN08904
EN1.4539, X1NiCrMoCu25-20-5
United Kingdom904S13 to BS 1501/3; 904S14 to BS 1554
SwedenSS 2562
South KoreaSTS890L to KS D 3698, KS D 3705 and KS D 3706
Romania2CuMoCrNi250 to STAS 3583
ISOX1NiCrMoCu25-20-5 to ISO 16143 and ISO 9328-7
Trade namesURANUS B6, NAS 255, FO 25-20 U, SOUDINOX B6

Buyers in Japan and Korea order this alloy as SUS890L or STS890L; buyers in Europe and North America order the same material as 904L or 1.4539. We work to whichever specification appears on the purchase order, and the certificate names the grade as you ordered it. Full data on the Western designation sits on the 904L forgings page.

05

Forging route and heat treatment

Stock is melted by electric furnace with ladle refining and vacuum oxygen decarburisation, by vacuum induction, or by either route followed by vacuum arc or electroslag consumable remelting where the order calls for it. Sufficient discard is taken from the ingot to clear piping and segregation.

Billets are hot worked between roughly 950 and 1150 °C. Working below 950 °C is avoided, because the alloy stiffens and turns crack sensitive. After forging, the standard condition is a solution treatment followed by rapid cooling. Mill datasheets give the solution treatment range as 1090 to 1175 °C. Where the order is placed to ASTM A182, the sequence is tighter: cool below 538 °C after hot working, solution treat at 1050 to 1150 °C, then liquid quench to below 260 °C.

The grade takes no strength from heat treatment and cannot be hardened thermally. Strength is raised only by cold work, and any cold worked part heading into stress corrosion cracking service should be solution treated again before it goes out.

Welding

All standard processes apply, using matching 904L electrodes and filler rods such as ER385 to AWS A5.9. The weld metal solidifies fully austenitic, so restrained joints are sensitive to hot cracking and joint design and heat input both matter. No preheat is used, and post weld heat treatment is normally not required.

Machining and surface condition

This is a clean, low sulphur grade and will not cut as freely as a free machining steel. It responds to standard methods with rigid setups, sharp tooling and positive feeds, and it bends cold to a small radius. Machined and fabricated surfaces should be pickled and passivated afterwards to restore the passive film.

06

Corrosion behaviour and service limits

The alloy was developed for sulphuric acid and keeps that reputation, but it also performs in phosphoric and acetic acid, in chloride bearing process water and in warm seawater. Service limits depend on concentration, temperature, aeration and contaminants, so a corrosion chart or a coupon test should settle any borderline duty rather than a datasheet.

SUS 890L against neighbouring grades
GradeCase for itCase for staying with SUS 890L
316LMuch lower cost, widely stocked.Far lower corrosion resistance in acids and chlorides.
Duplex 2205Higher strength at lower cost with very similar corrosion resistance.Not suited above about 300 °C, and SUS 890L holds the edge in sulphuric acid through its copper.
6 % Mo super austeniticsHigher pitting and crevice corrosion resistance. See Alloy 926 and Alloy 31.SUS 890L is the cheaper choice where 6 Mo performance is not needed.
Super duplexHigher corrosion resistance together with higher strength.Harder to forge and machine, and dearer in small quantities.
304L and 310LBetter in aggressive nitric acid, being molybdenum free.Both sit well behind in chlorides and reducing acids.

On temperature, the grade has good oxidation resistance but its structural stability falls away above about 400 °C, so it is not a high temperature material. In the other direction it stays tough into cryogenic service.

07

SUS 890L forged products

Every item is forged from a traceable heat and supplied as forged, proof machined or finish machined to drawing.

Seamless rolled rings

Ring rolled SUS 890L rings and rolled ring blanks for pumps, valves and vessels.

Forged flanges

Weld neck, blind, slip on, lap joint and special flanges to ASME B16.5, B16.47, EN 1092-1 or drawing.

Discs and tube sheets

Forged discs, tube sheets, covers and blind blanks for heat exchangers and reactors.

Shafts and spindles

Pump shafts, agitator shafts, eccentric shafts and stepped forged shafts.

Bars and hollow bars

Forged round and square bars, hollow bars for valve and fitting machining.

Sleeves and bushings

Forged sleeves, bushings, cylinders and hollow sections bored from solid.

Valve components

Valve bodies, bonnets, stems, seat rings and forged blocks.

Pipe and tube sections

Heavy wall forged pipe and tube sections where SUS890LTP or SUS890LTB sizes are not available.

Where these forgings are used

Chemical plant takes the largest share: rings, flanges, shafts and tube sheets for sulphuric, phosphoric and acetic acid service, fertiliser production, and pulp and paper processing. Marine and seawater work covers cooling equipment, pumps, gate valves on tanker ballast systems and desalination internals. Refinery and oil and gas users apply the grade to downhole and production equipment, wellhead and Christmas tree parts, and gas scrubbing plant. It also appears in heat exchangers, crystallisers, storage tanks, reactors, electrostatic precipitator components, and pharmaceutical and food processing equipment.

08

Testing, inspection and certification

Non-destructive testing is carried out to ASTM A388, EN 10228-3 or SEP 1921 as agreed on the order.

The standard package covers chemical analysis and PMI, tensile and proof strength with elongation, hardness, and dimensional inspection against the approved drawing. Intergranular corrosion testing to ASTM A262 or ASTM G28, pitting testing to ASTM G48 and similar order specific tests are placed with an accredited laboratory and the report is issued alongside the mill certificate; both need flagging at enquiry stage so they are scheduled before shipment rather than after.

Test specimens are taken from production forgings or from separately forged test blanks heat treated with the finished product, and are not removed until heat treatment is complete. Certificates are issued to EN 10204 3.1, or to EN 10204 3.2 witnessed by TUV, SGS, BV, LR or DNV.

09

The manufacturer

Jiangyin Jiangnan Metal Co., Ltd. is an integrated melting works and open-die forge at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China, operating since 1997.

Steel is melted on site rather than bought in as billet, so the certificate traces a part back to its melt number. Maximum heat size is 60 tonnes. Forging runs on 6,300 t, 4,000 t and 2,000 t hydraulic presses and on radial-axial ring mills to 6,000 mm outside diameter, with 14 heat treatment furnaces and a machine shop on the same site. The works holds CCS, BV, DNV, LR and NK approvals. Enquiries are handled by engineers who confirm the forging route, heat treatment condition, test package and certification before a price goes out.

Request a price for SUS 890L

Send the drawing or the rough sizes, the quantity, the governing specification, the delivery condition and the certificate type. Quotations normally come back within two working days. Minimum order is 10 kg with no minimum piece count, and normal lead time runs 20 to 60 days.

Jiangyin Jiangnan Metal Co., Ltd.
No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Tel 0086-189-2135-9659  ·  Email sales@steelforgepieces.com

Email the drawing Contact page
10

Questions we are asked about SUS 890L

Is SUS 890L the same as 904L?

For practical purposes, yes. SUS890L is the JIS designation in G4303, G4304 and G4305 for the alloy known internationally as 904L, UNS N08904 and EN 1.4539. The composition ranges match. What differs is the product standard, the test requirements and the wording on the certificate, so the order should always name one specification rather than both.

What is the UNS number for SUS 890L?

N08904. The EN number is 1.4539 and the EN name is X1NiCrMoCu25-20-5. In Korea the same grade is STS890L.

Which JIS standards cover SUS 890L?

JIS G4303 for bars, G4304 for hot rolled plate, sheet and strip, and G4305 for cold rolled plate, sheet and strip. Tube is SUS890LTB in JIS G3463 and pipe is SUS890LTP in JIS G3459. Forgings are most often ordered to ASTM A182 F904L instead, because JIS has no direct forging standard for this grade.

What are the mechanical minimums?

Proof stress 215 N/mm² minimum, tensile strength 490 N/mm² minimum, elongation 35 % minimum, hardness 90 HRB or 187 HB maximum, in the solution treated condition.

Can SUS 890L be hardened by heat treatment?

No. It is fully austenitic and takes no strength from thermal treatment. The supply condition is solution treated and rapidly cooled. Strength rises only through cold work, which should be removed by re-solution treating before stress corrosion cracking service.

Is SUS 890L magnetic?

No, it is non-magnetic. If a permeability limit matters for the application, state the figure on the enquiry.

What is the pitting resistance equivalent?

About 35, which puts it above 316L and below the 6 % molybdenum super austenitic grades.

What is the largest SUS 890L forging you can make?

Size depends on geometry and on which press or ring mill the job runs on. Rings roll up to 6,000 mm outside diameter and the heaviest single forging is 30 tonnes, but alloy content and section both affect what is sensible. Send the drawing with the finished dimensions and weight and we confirm the route and lead time.

How do I get a price?

Email the drawing or rough sizes, quantity, specification and certificate requirement to sales@steelforgepieces.com, or call 0086-189-2135-9659.

11

Related grades

Updated . Values are nominal and given for guidance; the purchase order and the governing specification take precedence. A plain text version of this page is available at SUS-890L.md.