GRADE SUH 310 / UNS S31000 STANDARD JIS G 4311 · JIS G 4312 WORKS Jiangyin, Jiangsu, China REV
Jiangyin Jiangnan Metal Melting works · Open-die forge · Ring mill Send drawing

Home / Stainless steel / SUH 310

Heat-resisting austenitic stainless · 25Cr-20Ni

SUH 310 Forgings Rolled rings, forged rings, flanges, bars, discs and shafts to JIS G 4311, melted and forged in one works

SUH 310 is the Japanese heat-resisting austenitic stainless steel carrying 24.0 to 26.0 percent chromium and 19.0 to 22.0 percent nickel, with carbon up to 0.25 percent. It is listed in JIS G 4311 for bars and wire rods and JIS G 4312 for plate, sheet and strip, and corresponds to AISI 310 and UNS S31000. The chromium builds a tenacious oxide and the nickel holds the structure austenitic, which is why the grade turns up in furnace hardware, carburising boxes and heat-treatment baskets rather than in chloride service.

Jiangyin Jiangnan Metal melts this grade on site through the electric arc furnace, ladle furnace and VOD route, then forges or ring-rolls it to drawing. The certificate traces the part back to its melt number, not to a purchased billet.

01

Chemical composition

Limits below are the JIS G 4311 and G 4312 chemistry for SUH 310. Iron makes up the balance.

SUH 310 composition, weight percent
CSiMnPSNiCrFe
0.25 max1.50 max2.00 max0.040 max0.030 max19.0–22.024.0–26.0bal.

Molybdenum and copper are not specified elements in the JIS chemistry for this grade. Where a purchase specification sets residual ceilings on them, we can hold those at the melt rather than screen for them afterwards. Note also that UNS S31000 permits phosphorus to 0.045 percent, slightly looser than the JIS 0.040 limit, so a part ordered to ASTM will not always satisfy a JIS chemistry check.

02

Mechanical properties

Room temperature values for solution treated bar.

SUH 310 solution treated, JIS G 4311
PropertyJIS minimumTypical published range, AISI 310 annealed
Proof stress, Rp0.2205 MPa205 to 310 MPa
Tensile strength, Rm590 MPa500 to 620 MPa
Elongation, A40 %30 to 47 %
Reduction of area, Z50 %—
Hardness201 HBW max185 to 207 HB
Fatigue strength at 107 cycles—206 to 228 MPa
Modulus of elasticity—196 to 204 GPa

One caution on elongation. The older JIS data gives 40 percent minimum, while the 2019 edition of G 4311 is published with 45 percent minimum for the solution treated condition. State the edition that governs your order and we will test against it.

A part ordered to ASTM A182 F310 and the same part ordered to JIS SUH 310 are not interchangeable on paper. The ASTM and ASME route for 310 and 310S is commonly written around 515 to 520 MPa minimum tensile with 205 MPa proof stress and 40 percent elongation, well below the 590 MPa the JIS bar standard asks for. Tell us which document governs and the test certificate will be written to it.

03

Physical properties

Density7.98 g/cm³
Melting range1400–1450 °C
Max service1050–1150 °C
Min service−200 °C
PREN24–26
MagneticNo
Indicative thermal and electrical data, SUH 310 and AISI 310
Thermal conductivity11 to 16 W/m·°C
Specific heat capacity490 to 530 J/kg·°C
Coefficient of thermal expansion15 to 17 µm/m·°C
Electrical resistivity72 to 90 µΩ·cm
Magnetic responseNon-magnetic in the solution treated condition

Expansion matters more than the number suggests. At 15 to 17 micrometres per metre per degree, a 2 metre furnace ring grows close to 30 mm on the way up to 1000 C. Clearance and location features need to be drawn for the hot condition, not the cold one.

04

Equivalent grades

International grades of similar composition
Country or bodyDesignationSpecification
JapanSUH 310JIS G 4311, JIS G 4312
United StatesAISI 310, UNS S31000, F310 forgingsASTM A182, A336, A965, A276
EuropeX15CrNi 25-20 (1.4845), X15CrNiSi 25-20 (1.4841)EN, DIN
China20Cr25Ni20, 2Cr25Ni20, S31020GB
South KoreaSTR 310KS
United Kingdom310S31BS
FranceZ15CNS 25-20NF
Russia20Kh25N20S2GOST
ISOX15CrNi 25-21ISO

Cross references of this kind are close matches, not drop-in substitutions. Silicon in particular separates 1.4841 from 1.4845, and that difference changes scaling behaviour at the top of the temperature range.

SUH 310 against 310S

Buyers ask this almost every week. Chromium and nickel are the same in both, so the oxidation ceiling near 1150 C is the same. Carbon is what differs: 310S is held lower and welds more easily, while the higher carbon permitted in 310 and SUH 310 earns better strength at temperature. If the forging gets welded into an assembly, 310S is the safer line on the order. If it runs hot as a standalone part, SUH 310 is the one to specify. Both are on our melt list.

05

Forging and heat treatment

Hot work on the open-die presses or the ring mill, then solution treat and quench so the chromium carbides go back into solution and the structure finishes fully austenitic.

Works practice for SUH 310
OperationPractice
MeltingEF, LF and VOD. ESR remelt available where cleanliness or segregation control is specified.
Forging6,300 t, 4,000 t or 2,000 t press depending on section. Radial-axial ring rolling on the 6 m, 3 m or 1 m mill.
Solution treatment1050 to 1150 C, soak set by section thickness, then rapid quench. Carried out in the car-bottom or well furnaces on site.
QuenchWater as standard. Thin or complex sections quenched to control distortion, with the route agreed before production.
RecordsFurnace charts recorded against the heat treatment lot and issued with the certificate.

Welding, stated plainly

Supplier pages tend to call this grade freely weldable. The published ratings are more guarded. For AISI 310 the weldability ratings for TIG, MIG and plasma come out as fair rather than good, submerged arc is listed as not recommended, and the literature on 25Cr-20Ni austenitics with high silicon flags sensitivity to weld hot cracking. No preheat and no post-weld heat treatment are needed, and matching filler is normal. We raise the point because it changes fabrication planning after the forging leaves us, and finding out at the weld bench is expensive.

06

Shapes and working envelope

Every item is forged from a single piece of steel melted at this works. No welding, no casting, no billet of unknown origin.

SUH 310 product forms and size limits
FormItemsSize limit
Seamless rolled ringsRectangular and contoured section, gear ring blanks, slewing ringsto OD 6,000 mm
Forged ringsUpset and punched rings, retaining rings, valve seat ringsfrom OD 50 mm
FlangesWeld neck, blind, slip-on, lap joint, orifice, long weld neck blanksto 5,000 mm machined dia
Discs and tube sheetsSolid discs, tube sheets, covers, proof-machined for volumetric inspectionto 5,000 mm machined dia
Bars and blocksRound, flat and square bars, blocks for machined bodiesby drawing
Shafts and spindlesStepped shafts, pinion shafts, rolls, rotors, tie rodsto 14,000 mm turned length
Cylinders and sleevesHollow cylinders, sleeves, bushings, heavy-wall pipe sections bored from solidto 1,600 mm dia x 10,000 mm
Valve partsBodies, bonnets, stems, seat rings, nozzles, manifoldsby drawing
Single piece weightSet by the 60 t heat size and the 6,300 t pressto 30,000 kg

Minimum order is 10 kg with no minimum piece count, so a single prototype ring is worth asking about. Normal lead time runs 20 to 60 days depending on melt route and heat treatment.

07

Where SUH 310 is used

Specify it when a part has to hold its strength and keep its oxide skin in hot, oxidising air.

The documented uses for this grade are furnace parts, carburising boxes, heat-treatment baskets and jigs, oil burner parts, heat exchangers, electrical parts, and welding filler wire and electrodes. In forged form we see it most often as furnace rolls and roller-hearth hardware, kiln and annealing line fixtures, burner and combustion chamber components, radiant tube flanges and supports, thermal oxidiser internals, and reformer and cracking furnace hardware in petrochemical plant.

Where to use something else

SUH 310 is a high-temperature grade, not a chloride grade. Published ratings put it at moderate resistance in seawater and in sour oil and gas, the PREN sits around 24 to 26, and there is slight susceptibility to chloride stress corrosion cracking. For seawater, desalination, subsea or wellhead duty we would quote A182 F51, F53 or F55 duplex, 904L, A182 F44 or Incoloy 825. Where service is hotter or more carburising than 310 will take, step up to AISI 330, Incoloy 800H, Inconel 601 or Inconel 617.

08

Testing and certificates

The melt number on the certificate traces back to the furnace, because the furnace is ours.

Standard inspection scope
ItemStandard or scope
Ultrasonic examinationEN 10228-3, SEP 1921 or ASTM A388, to the class stated on the order
Chemical analysisLadle and product analysis against JIS G 4311 or the governing specification
Mechanical testingTensile, hardness, impact where specified, test location agreed before production
MetallurgicalGrain size, intergranular corrosion testing where required
CertificationEN 10204 3.1, or 3.2 witnessed by a third party
Works approvalsCCS, BV, DNV, LR, NK
09

Questions we are asked

What is SUH 310 steel?

A Japanese heat-resisting austenitic stainless steel with 24.0 to 26.0 percent chromium, 19.0 to 22.0 percent nickel and carbon to 0.25 percent, listed in JIS G 4311 for bars and wire rods and JIS G 4312 for plate, sheet and strip. It is the JIS counterpart of AISI 310 and UNS S31000.

What is SUH 310 equivalent to?

UNS S31000 and AISI 310 in the United States, 1.4845 or 1.4841 in Europe, 20Cr25Ni20 in China, STR 310 in South Korea, 310S31 in Britain, 20Kh25N20S2 in Russia. For forgings the matching American specifications are ASTM A182 F310, A336 F310 and A965 F310. The full table is in section 04.

How hot can SUH 310 run?

Type 310 resists oxidation in dry air to roughly 1150 C, and published maximum service figures span 1050 to 1150 C. Thermal cycling lowers that, and around 1035 C is the figure usually applied to intermittent service, because repeated heating and cooling makes the scale spall.

Is SUH 310 magnetic?

No. It is austenitic and classed as non-magnetic. Parts ship solution treated and non-magnetic. Heavy cold work can raise a slight response.

310 or 310S?

Carbon is the only real difference. Lower in 310S, which welds more easily. Higher in 310 and SUH 310, which holds strength better at temperature. Same chromium, same nickel, same oxidation ceiling.

Will it stand up to seawater or sour service?

Not well enough to recommend. Ratings for AISI 310 come out moderate in seawater and in sour oil and gas, PREN around 24 to 26, with slight susceptibility to chloride stress corrosion cracking. Duplex, 904L, A182 F44 or a nickel alloy is the right answer for those duties.

How small or large can you go?

From 10 kg with no minimum piece count, up to a 30 tonne single piece. Rolled rings reach 6,000 mm outside diameter, shafts 14,000 mm turned length, discs and tube sheets 5,000 mm machined diameter.

How do I get a price?

Email the drawing in PDF, DWG or STEP to sales@steelforgepieces.com or call +86 189 2135 9659. Include quantity, the governing specification, delivery condition, NDT class and the certificate level you need. Drawings received in the morning are normally quoted the same working day.

Quote SUH 310 to your drawing

Material, forging, heat treatment, machining, NDT and certification come back as one price from one works. Minimum 10 kg. Lead time 20 to 60 days.

sales@steelforgepieces.com

+86 189 2135 9659
No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Monday to Saturday, 08:00 to 17:30 China Standard Time