What is ASTM A182 F49
ASTM A182 Grade F49 is a super-austenitic stainless steel forging grade, UNS S34565, containing about 24 percent chromium, 17 percent nickel, 6 percent manganese, 4.5 percent molybdenum and 0.4 to 0.6 percent nitrogen. It belongs to the 6Mo, high-nitrogen family. Buyers specify it when chloride pitting and crevice corrosion have to be resisted at a strength level that ordinary austenitic grades cannot reach.
The high manganese content has a purpose. Manganese raises the solubility of nitrogen in austenite, which is what makes the 0.4 to 0.6 percent nitrogen addition possible in the first place. That nitrogen then does two jobs. It carries the largest weighting in the PREN formula, and it roughly doubles the yield strength against 316L.
Under EN designation the grade is X2CrNiMnMoN25-18-6-5. Some producer datasheets print it as X2CrNiMnMoNbN25-18-5-4, which reflects the optional niobium addition. Both point to material number 1.4565. Being fully austenitic, F49 is non-magnetic in the solution-annealed condition and cannot be hardened by heat treatment.
Chemical composition of A182 F49 and UNS S34565
The ASTM and EN chemistry windows are close but they are not the same. Chromium, nickel, sulfur and niobium all differ. Order against whichever standard your drawing names, and do not treat the two as interchangeable on a purchase order.
| Element | ASTM A182 F49 / ASME SA-182 F49 (UNS S34565) | EN 1.4565 / Alloy 24 |
|---|---|---|
| Carbon (C) | 0.030 max | 0.03 max |
| Silicon (Si) | 1.00 max | 1.00 max |
| Manganese (Mn) | 5.00 to 7.00 | 5.00 to 7.00 |
| Phosphorus (P) | 0.030 max | 0.03 max |
| Sulfur (S) | 0.010 max | 0.015 max |
| Chromium (Cr) | 23.00 to 25.00 | 24.0 to 26.0 |
| Nickel (Ni) | 16.00 to 18.00 | 16.0 to 19.0 |
| Molybdenum (Mo) | 4.00 to 5.00 | 4.00 to 5.00 |
| Nitrogen (N) | 0.40 to 0.60 | 0.30 to 0.60 |
| Niobium (Nb, Cb) | 0.10 max | 0.15 max |
| Iron (Fe) | Balance | Balance |
PREN, pitting resistance equivalent number
PREN is calculated as percent Cr plus 3.3 times percent Mo plus 16 times percent N. Applied to the ASTM A182 F49 limits, the result is about 42.6 at the lean end of the window and about 46.9 at the rich end, so a PREN in the mid-40s is normal for this grade. Those two figures are calculated from the specification range, not measured on a heat. The PREN of the material you actually receive follows from the heat analysis on the mill certificate.
Mechanical and physical properties
| Property | ASTM A182 F49, minimum | EN 1.4565, typical |
|---|---|---|
| Tensile strength, Rm | 795 MPa (115 ksi) | 800 to 950 MPa |
| Yield strength, Rp0.2 | 415 MPa (60 ksi) | 420 MPa |
| Elongation, 50 mm or 4D | 35 percent | 35 percent |
| Reduction of area | 40 percent | not stated |
| Hardness | not stated | about 230 HB 30 |
| Modulus of elasticity | not stated | 190 kN/mm2 |
| Charpy ISO-V at room temperature, over 10 mm | not stated | about 120 J longitudinal, 90 J transverse |
| Property | Value |
|---|---|
| Density | 8.0 g/cm3 |
| Specific heat capacity | 450 J/(kg K) |
| Thermal conductivity | 12 W/(m K) |
| Electrical resistivity | 0.92 ohm mm2/m |
Service temperature
Alloy 24 is treated as a wet corrosion material for service to roughly 400 C. The VdTUV material sheet 509 covers it for pressure applications from minus 196 C to plus 400 C. Check the design code governing your vessel or piping before you rely on either limit.
Forging and heat treatment
Our open-die practice follows the published window for the grade. Forging runs between roughly 1150 C and 950 C, followed by air cooling. F49 work hardens quickly and its hot working range is narrower than a 300-series austenitic, so we plan reheats to hold the finishing temperature above 950 C. Dropping below that invites intermetallic sigma and chi precipitation as heavy sections cool.
Solution annealing is done at 1170 to 1120 C with a water quench. The quench is not a detail that can be relaxed. It is the step that holds nitrogen and molybdenum in solution, and it is the reason the finished forging still has the corrosion resistance the alloy was bought for. Heavy rings and thick tube sheets are quenched with agitation so the cooling rate carries through section.
For welded fabrication the usual filler is a nickel-base consumable of the Alloy 59 type, material 2.4609. It is chosen so the weld metal PREN over-matches the parent material rather than becoming the first thing to pit in a chloride environment.
A182 F49 forged products we make
Everything listed here is produced to customer drawing or specification. Send a dimensioned drawing and we quote rough forged, proof machined or finish machined.
Seamless rolled rings
Radial-axial rolled rings for flanged joints, bearing housings, valve seat rings and pressure retaining parts.
Forged flanges
Weld neck, slip-on, blind, lap joint and special bore flanges to ASME B16.5, B16.47 or to drawing.
Round bar and shafts
Forged bar, stepped shafts, eccentric shafts, spindles and pump shafts for seawater and FGD duty.
Discs, blanks and tube sheets
Upset forged discs, blind discs, gear blanks and heat exchanger tube sheets in heavy section.
Sleeves, bushings and hollows
Trepanned or mandrel forged hollow sections, sleeves, bushings and cylinder liners.
Valve and pressure parts
Valve bodies, bonnets, stems, seat rings, blocks and forged nozzles for chemical process service.
Where A182 F49 is used
Alloy 24 and S34565 resist intergranular corrosion and perform well against pitting, crevice corrosion and stress corrosion cracking in seawater and other chloride-bearing media. It is often specified in place of a duplex grade, Alloy 31 or a nickel-base alloy when those are either not strong enough or not economic. Published fields of application cover the chemical process industry, flue gas desulphurisation plant in power stations and on large sea-going vessels, seawater desalination and other seawater systems, heat exchangers, and the food and pharmaceutical industries. The grade also appears in the German technical approval Z-30.3-6 for swimming pool and tunnel work, in resistance class IV.
Within those sectors, the parts customers order from us in F49 include FGD absorber and scrubber internals, seawater ballast and cooling system components, seawater pump and valve parts, desalination plant piping components, bleaching equipment for pulp and paper, acid cleaning and pickling equipment, and offshore hardware that has to carry load as well as resist chlorides.
Testing, inspection and documents
Ultrasonic testing is carried out to EN 10228-4, the part of the EN 10228 series written for austenitic and austenitic-ferritic stainless steel forgings. ASTM A388 is used where a customer specification calls for it. This is worth stating plainly, because EN 10228-3 is quoted for stainless forgings surprisingly often, including on the earlier version of this page. Part 3 applies to ferritic and martensitic steel forgings and is the wrong reference for F49.
The test scope we can offer covers spectrometer chemical analysis, room temperature tensile and Charpy V-notch impact testing, hardness survey, intergranular corrosion testing to ASTM A262 practice E, pitting testing to ASTM G48, PMI verification, dimensional inspection and liquid penetrant examination.
Material certificates are issued to EN 10204 type 3.1, signed by an authorised inspection representative independent of the production department. Where third-party witness is required, EN 10204 type 3.2 certificates countersigned by an independent body such as TUV, SGS, BV, DNV or Lloyd's Register can be arranged at order stage.
Frequently asked questions
Is ASTM A182 F49 the same as UNS S34565 and EN 1.4565
F49 is the identification symbol used in ASTM A182. UNS S34565 is the unified number for the same alloy. EN 1.4565, also sold as Alloy 24, is the corresponding European grade. The composition limits differ slightly. Chromium is 23.00 to 25.00 percent in ASTM against 24.0 to 26.0 percent in EN, nickel is 16.00 to 18.00 against 16.0 to 19.0, and sulfur is 0.010 max against 0.015 max.
What is the PREN of A182 F49
Applying PREN equals percent Cr plus 3.3 times percent Mo plus 16 times percent N to the ASTM A182 F49 limits gives about 42.6 at the low end and about 46.9 at the high end, so the mid-40s is typical. The figure for a given order depends on the heat analysis and is traceable from the mill certificate.
What are the minimum mechanical properties of A182 F49
ASTM A182 requires 795 MPa (115 ksi) minimum tensile strength, 415 MPa (60 ksi) minimum yield, 35 percent minimum elongation in 50 mm or 4D, and 40 percent minimum reduction of area.
Can A182 F49 be hardened by heat treatment
No. It is fully austenitic and is supplied solution annealed, typically 1120 to 1170 C followed by a water quench. Strength comes from nitrogen held in solid solution and from any retained cold work, not from a hardening transformation.
Which ultrasonic testing standard applies
EN 10228-4, which covers ultrasonic testing of austenitic and austenitic-ferritic stainless steel forgings. EN 10228-3 covers ferritic and martensitic forgings and does not apply to F49. ASTM A388 is used when specified.
What documents come with the forgings
EN 10204 type 3.1 as standard, covering heat chemistry, mechanical test results, the heat treatment record and NDT results. Type 3.2 with third-party countersignature is available on request. Ultrasonic results are reported to EN 10228-4 or ASTM A388.
What sizes and weights can you forge
We are an open-die shop working to drawing across a wide range of rings, bars, discs, shafts and hollows. Send the drawing or the rough dimensions and finished weight and we will confirm it against our press and ring rolling capacity, with price and lead time.
Request a quotation for A182 F49 forgings
Send a drawing, rough dimensions or your specification and we will come back with price and lead time, normally within 24 hours on a working day.
sales@steelforgepieces.com | +86 189-2135-9659 | No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Standards referenced
- ASTM A182 / A182M, forged or rolled alloy and stainless steel pipe flanges, forged fittings, valves and parts for high temperature service, Grade F49, UNS S34565.
- ASME SA-182 Grade F49, composition and mechanical property requirements.
- EN 10088-2, stainless steels, technical delivery conditions, material 1.4565, X2CrNiMnMoN25-18-6-5.
- EN 10228-4, non-destructive testing of steel forgings, part 4, ultrasonic testing of austenitic and austenitic-ferritic stainless steel forgings.
- EN 10204, metallic products, types of inspection documents, 3.1 and 3.2.
- ASTM A388 ultrasonic examination, ASTM A262 intergranular attack, ASTM G48 pitting and crevice corrosion.
- VdTUV Werkstoffblatt 509, pressure application approval for 1.4565.
Figures on this page are taken from published standards and alloy producer datasheets and are given for guidance. They do not replace the mill certificate for a specific heat and are not a design warranty. Check every value against the code governing your application.
Prepared by the technical department of Jiangyin Jiangnan Metal Co., Ltd. Last reviewed .