Open-die forging factory since 1997. Jiangyin, Jiangsu, China. CCS, BV, DNV, LR, NK. +86 189 2135 9659  |  sales@steelforgepieces.com
Jiangyin Jiangnan Metal Co., Ltd.Steel melting, open-die forging, ring rolling Get a quote

Z6CNDT17-12 Forgings and Seamless Rolled Rings

AFNOR designation for titanium-stabilised 17Cr-12Ni-2Mo austenitic stainless steel. EN X6CrNiMoTi17-12-2 (1.4571), AISI 316Ti, UNS S31635. Forged to drawing in Jiangyin, China, from steel melted on site.

EN equivalent1.4571
UNSS31635
Tensile, Rm500-700 MPa
Proof, Rp0.2 min200 MPa
Hardness max215 HB
PREN23.1-26.7
Max ring OD6,000 mm
Max piece weight30 t

Summary

Z6CNDT17-12 is the French AFNOR designation for a titanium-stabilised austenitic chromium-nickel-molybdenum stainless steel. The European equivalent is X6CrNiMoTi17-12-2, material number 1.4571. The American equivalent is AISI 316Ti, UNS S31635. Titanium at five times the carbon content binds carbon as titanium carbide, so the steel keeps its resistance to intergranular corrosion after welding. Molybdenum at 2.0 to 2.5 percent gives better pitting and crevice resistance than 1.4301. The cost of the titanium addition is machinability, since titanium carbonitrides form during cutting and wear tooling.

Jiangyin Jiangnan Metal Co., Ltd. forges the grade as rings, seamless rolled rings, flanges, shafts, discs, tube sheets, sleeves, bushings and bars, from steel melted in its own shop, with EN 10204 3.1 or 3.2 certification. Minimum order 10 kg, rings to 6,000 mm outside diameter, single pieces to 30 t.

1. The grade

The designation follows the older French naming system. Z marks a high-alloy steel, 6 stands for about 0.06 percent carbon, C N D T are chromium, nickel, molybdenum and titanium, and 17-12 gives the nominal chromium and nickel contents.

Two alloying additions define the grade. Molybdenum at 2.0 to 2.5 percent lifts resistance to pitting and crevice attack above that of a plain 18/10 steel. Titanium is a stronger carbide former than chromium and holds carbon as TiC, so chromium stays in solution through welding and through the 425 to 815 C sensitisation range. That is why the grade can be welded without a solution anneal afterwards for corrosion reasons.

Specification note. Z6CNDT17-12 is a legacy designation. The AFNOR forging standard it belongs to, NF A36-607, austenitic stainless steel parts obtained by flat die forging or drop forging for boilers and pressure vessels, is listed by AFNOR as cancelled. New orders are normally written against EN 10088-3, EN 10222-5 (steel forgings for pressure purposes, martensitic, austenitic and austenitic-ferritic stainless steels) or ASTM A182 F316Ti. We forge to the AFNOR limits where a legacy drawing calls for them. State this on the enquiry.

2. Equivalent grades and governing standards

Z6CNDT17-12 international cross reference
System or countryDesignation
France, AFNOR NFZ6CNDT17-12, Z6CNT17-12, Z8CNDT17-12
EN, WerkstoffX6CrNiMoTi17-12-2, 1.4571
Germany, DINX6CrNiMoTi17-12-2, X10CrNiMoTi18-10
USA, AISI and UNS316Ti, TP316Ti, UNS S31635
Japan, JISSUS316Ti, 316Ti
UK, BS320S31, 320S18, 321S12
Italy, UNIX6CrNiMoTi17-12
China, GB0Cr18Ni12Mo2Ti, 1Cr18Ni12Mo2Ti, 06Cr17Ni12Mo2Ti
Sweden, SS2350, 2350-02
Poland, PNH17N13M2T
Czechia, CSN17348
Russia, GOST08Kh17N13M2T, 10Kh17N13M2T
Spain, UNEF.3535
Standards in which the grade or its equivalents appear
StandardScope
NF A36-607Austenitic stainless steel parts obtained by flat die forging or drop forging for boilers and pressure vessels, grades and types. Cancelled.
NF A35-574Stainless steel for general purposes, semi-finished products, bars and wire rod
NF A35-573Stainless steels for general purposes, plates, wide strips and strips
NF A35-578Stainless steel for high-temperature application
NF A36-209Austenitic and austenitic-ferritic stainless steel plates for boilers and pressure vessels
EN 10088-3Stainless steels, semi-finished products, bars, rods, wire, sections and bright products, grade 1.4571
EN 10222-5Steel forgings for pressure purposes, martensitic, austenitic and austenitic-ferritic stainless steels
ASTM A182, ASME SA-182Forged or rolled alloy and stainless steel pipe flanges, forged fittings, valves and parts, Grade F316Ti

3. Chemical composition

The three systems are equivalent, not identical. The AFNOR window is the tightest on carbon, silicon and nickel. ASTM is the widest on molybdenum and nickel. A heat that passes 1.4571 can fail Z6CNDT17-12 on carbon or nickel, so the governing standard has to be fixed before the melt is booked.

Composition limits in weight percent
ElementAFNOR Z6CNDT17-12EN 1.4571, X6CrNiMoTi17-12-2ASTM 316Ti, UNS S31635
C0.060 max0.08 max0.08 max
Si0.75 max1.00 max1.00 max
Mn2.00 max2.00 max2.00 max
P0.040 max0.045 max0.045 max
S0.015 max0.015 max, see note0.030 max
N0.020 maxnot specifiednot specified
Cr16.00 to 18.0016.5 to 18.516.0 to 18.0
Ni10.50 to 12.5010.5 to 13.510.0 to 14.0
Mo2.00 to 2.502.00 to 2.502.0 to 3.0
Ti5 x (C+N) min, 0.70 max5 x C min, 0.70 max0.70 max
FeBalance

Published EN data sheets differ on the sulphur ceiling for 1.4571. Both 0.015 and 0.030 percent appear in circulation. Confirm against the edition of EN 10088-3 being purchased to.

The stabilisation ratio matters more than any single figure. Some specifications write it as 5 x C, others as 5 x (C+N). State which applies, since it changes the titanium aim in the ladle.

4. Mechanical properties at room temperature

Values are for the solution-annealed condition. Forgings are tested on a representative test piece under the governing standard.

Room-temperature properties, solution annealed
PropertyEN 10088-3, 1.4571, dia 160 mm or lessPublished 316Ti and Z6CNDT17-12 data
Tensile strength Rm500 to 700 MPa515 MPa min
Proof strength Rp0.2200 MPa min205 MPa min
Proof strength Rp1.0235 MPa minnot stated
Elongation A, longitudinal40 percent min40 percent min in 50 mm
Hardness215 HB maxnot stated
Impact energy KV at 20 C100 J min, drawn barnot stated
Other product forms of the 1.4571 equivalent, for reference
FormRm, MPaRp0.2, MPaA, percent
Hot-rolled peeled bar500 to 700over 200not stated
Drawn bar500 to 950over 200over 25
Hot-rolled plate520 to 670over 220over 40
Cold-rolled strip540 to 690over 240over 40
Seamless hot-rolled tubenot statedover 190over 40

5. Proof strength at elevated temperature

Solution-annealed condition. These are the figures a pressure vessel or piping designer needs when the part runs hot.

Elevated-temperature proof strength, 1.4571 and Z6CNDT17-12, MPa
Temperature, C100150200250300350400450500550
Rp0.2 min185175165155145140135131129127
Rp1.0 min215205192183175169164160158157

Published data gives a maximum service temperature of about 550 C for this grade, and notes that 316Ti can be held in service for long periods at up to 500 C without loss of corrosion resistance. The grade is also suitable for low-temperature service.

6. Physical properties

Physical properties at 20 C unless stated
PropertyValueUnit
Density8.0kg/dm3
Modulus of elasticity200GPa
Thermal conductivity15W/m.K
Specific heat capacity500J/kg.K
Electrical resistivity0.75ohm.mm2/m
Magnetisabilitylow, relative permeability 1.3 max-
PREN23.1 to 26.7-

Thermal conductivity is low and thermal expansion is high, so thin sections distort more readily than carbon steel during heating and quenching. This shows up on long shafts and thin-walled rings during heat treatment. Although the structure is austenitic, the grade can show some magnetic response, so a magnet is not a reliable way to identify it.

7. Corrosion behaviour

Intergranular corrosion

Resistant both as delivered and as welded. Titanium ties up carbon, so chromium carbides do not precipitate at grain boundaries.

Pitting and crevice

Better than 1.4301 because of the molybdenum addition. PREN 23.1 to 26.7.

Seawater and high chloride

Not resistant, pitting can occur. For seawater duty use a 6 Mo grade such as A182 F44 or a duplex such as F51.

Acids

Resistant to organic acids such as formic acid, and to sulphuric acid in low and medium concentrations, within the limits of the published data.

Published sources are not consistent on this grade in nitric acid and in some strong mineral acids. Corrosion data depends on medium, temperature and concentration. Treat the table above as a screening guide and verify against the actual service conditions before selecting the grade.

8. Forging and heat treatment

Thermal processing of Z6CNDT17-12 and 1.4571
OperationTemperatureCooling
Heating for forging1150 to 1180 C-
Forging range1180 down to 950 C, hot forming cited as 1200 down to 900 CWater after forging, air after hot forming
Solution annealing1020 to 1120 CWater or air, rapid

Forgeability is good and the grade suits both open-die forging and drop forging. In our shop the forging is cogged or ring-rolled from an on-site melt, returned to the furnace as often as the reduction schedule needs, then solution annealed in one of fourteen heat treatment furnaces. Soak time is set by ruling section. Long shafts are quenched vertically in a 15 m well-type furnace to hold distortion down, which matters for a steel with this expansion coefficient.

9. Welding and machining

Welding

Good weldability with all common processes except gas welding. A filler metal is not strictly required. Where one is used, 1.4430 is a commonly recommended choice. Post-weld heat treatment is not needed and welding does not impair resistance to intergranular corrosion. In bare-wire processes much of the titanium is lost across the arc, which is why matching or niobium-stabilised fillers are often specified.

Machining

Moderate to poor, and worse than other chromium-nickel-molybdenum stainless steels. Titanium carbonitrides form during cutting and accelerate tool wear. This is not a free-machining grade and it is the wrong choice for demanding high-speed machining. Rigid setups, sharp positive-rake tooling and a steady feed that keeps the tool below the work-hardened layer are the usual measures. Cold forming and cold pressing present no particular difficulty.

10. Forged product forms in Z6CNDT17-12

Open-die and ring-rolled forms produced in this grade
FormTypical partsSize envelope
Seamless rolled ringsRing blanks, bearing rings, retaining rings, flange blanks, contoured ringsOD 50 to 6,000 mm
Forged ringsValve seat rings, gear rings, heavy sections outside the mill envelopeUpset and punch route
Forged flangesWeld neck, blind, slip-on, socket weld, lap joint, orifice, long weld neckASME B16.5, B16.47, API 6A
Shafts and spindlesStepped shafts, eccentric shafts, valve stems, pins, rollsto 14,000 mm turned length
Bars, blocks and blanksRound, flat and square bar, gear blanks, wheels, manifoldsper drawing
Discs and tube sheetsSolid discs, tube sheets, covers, blind plates, hubsto 5,000 mm machined
Cylinders, sleeves, bushingsHollow cylinders, liners, couplings, heavy-wall pipe sectionsbore to 1,600 x 10,000 mm
Valve and pump partsBodies, bonnets, blocks, seat rings, nozzles, spoolsper drawing

Supplied as forged with machining allowance, proof-machined for ultrasonic inspection, or finish-machined to drawing. Single pieces up to 30 tonnes. Minimum order 10 kg with no minimum piece count, so a one-off replacement part can be quoted.

11. Where the grade is used

Chemical and petrochemical

Pressure vessel flanges, tube sheets, covers, nozzles, chemical transport containers, heat exchanger components, piping parts in contact with process chemicals.

Oil, gas and offshore

Subsea and deepwater production hardware, compressor and generator components, spools and valve parts.

Pulp, paper and refining

Digesters, liquor tanks, paper machine components, refinery catalytic recovery systems and recuperators.

Food and pharmaceutical

Food preparation and storage equipment, in particular in acidic environments, and pharmaceutical production hardware.

Marine and shipbuilding

Apparatus engineering, pipeline construction and shipbuilding components, covered by CCS, BV, DNV, LR and NK approvals.

Power and rotating equipment

Turbine and gas compressor parts, gearbox blanks, power transmission rings, pressure vessel and pipeline construction.

12. Testing, inspection and certification

Because the steel is melted here, chemistry is verified at the furnace rather than inherited from a billet supplier certificate, and the melt number follows the part through forging, heat treatment, machining and shipment.

Standard and optional testing for Z6CNDT17-12 forgings
TestMethod or standardScope
Chemical analysisASTM E415 optical emission, ASTM E1019 for C and SEvery heat, in house
TensileASTM A370, ISO 6892Every order, in house
Impact, Charpy VASTM A370, down to minus 60 COn request, in house
Ultrasonic testingASTM A388, EN 10228-3, SEP 1921To the class stated on the order
Magnetic particle, PMIASTM E709, handheld alloy analyserOn request
Grain size and metallographyASTM E112On request
Intergranular corrosionASTM A262, ASTM G28Accredited third-party laboratory
Pitting resistanceASTM G48Accredited third-party laboratory
CertificateEN 10204 3.1 standard, 3.2 witnessed by BV, DNV, LR, SGS, TUV or your inspectorEvery shipment

13. The plant behind the part

Most forging suppliers in China buy billet. This works melts its own steel, which for a titanium-stabilised grade is a metallurgical point rather than a sales one, since the titanium aim and the carbon plus nitrogen balance are set in our ladle instead of being accepted as delivered.

Capability relevant to Z6CNDT17-12 forgings
StageEquipmentCapacity
MeltingElectric arc furnace, ladle furnace, vacuum oxygen decarburisation60 t max heat, VOD 30 t and 60 t
Remelting, optionalProtective-atmosphere ESR, VIM, VARESR 3 t and 6 t, VIM 3 t, VAR 6 t
ForgingHydraulic open-die presses, hammers6,300 t, 4,000 t, 2,000 t, hammers 750 kg to 5 t
Ring rollingRadial-axial ring mills6 m, 3 m, 1 m, max OD 6,000 mm
Heat treatment14 furnaces, including 3 high-temperature and 2 well-typechamber to 8,000 x 2,000 x 2,000 mm, 15 m deep pit
MachiningVertical and horizontal lathes, CNC, deep-hole drilling5,000 mm swing, 14 m centres, bore 1,600 x 10,000 mm

Operating since 1997 with 460 staff, including 9 senior engineers and 32 intermediate engineers. Class approvals CCS, BV, DNV, LR and NK. Exports to North America, Europe, the Middle East and Asia-Pacific.

14. Request a quotation

A price comes back within two working days of a complete enquiry. Six items are what the estimator needs. Anything missing means a round trip of questions first.

What to include in a Z6CNDT17-12 enquiry
No.ItemExample
1Grade and governing standardZ6CNDT17-12 to AFNOR limits, or 1.4571 to EN 10222-5
2Dimensions or drawingOD 1200 x ID 900 x H 260 mm, PDF, DWG, DXF, STEP
3Quantity and repeat volume12 pieces, about 4 times per year
4Delivery conditionAs forged, proof-machined or finish-machined
5Heat treatment and testingSolution annealed 1050 C water quench, UT to ASTM A388, ASTM A262 Practice E
6Certification and destinationEN 10204 3.2 witnessed by DNV, Rotterdam

Jiangyin Jiangnan Metal Co., Ltd.

Open-die forging factory with its own melt shop, established 1997.

Plant

No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China, 214423

Phone

+86 189 2135 9659
Monday to Saturday, 08:00 to 17:30, UTC+8

Email

sales@steelforgepieces.com
English and Chinese

Terms

Minimum order 10 kg, lead time 20 to 60 days, quotation in 2 working days, EN 10204 3.1 or 3.2

Open a pre-filled enquiry email

15. Questions we are asked about this grade

What is Z6CNDT17-12 steel?

It is the AFNOR designation for a titanium-stabilised austenitic chromium-nickel-molybdenum stainless steel. The European equivalent is X6CrNiMoTi17-12-2, material number 1.4571. The American equivalent is AISI 316Ti, UNS S31635. Titanium at five times the carbon content binds carbon as titanium carbide, so the steel resists intergranular corrosion in the as-welded condition, and molybdenum at 2.0 to 2.5 percent improves pitting and crevice resistance over 1.4301.

Is Z6CNDT17-12 the same as 1.4571 and 316Ti?

Equivalent, not identical. AFNOR limits carbon to 0.060 percent, silicon to 0.75 percent, chromium to 16.0 to 18.0 and nickel to 10.5 to 12.5. EN 1.4571 allows carbon to 0.08 percent, silicon to 1.00 percent, chromium 16.5 to 18.5 and nickel 10.5 to 13.5. ASTM 316Ti allows molybdenum to 3.0 percent and nickel to 14.0 percent. A heat certified to 1.4571 does not automatically meet the narrower AFNOR window, so name the governing standard on the purchase order.

What is the chemical composition of Z6CNDT17-12?

To the AFNOR limits: C 0.060 max, Si 0.75 max, Mn 2.00 max, P 0.040 max, S 0.015 max, Cr 16.00 to 18.00, Mo 2.00 to 2.50, Ni 10.50 to 12.50, N 0.020 max, Ti from 5 x (C+N) up to 0.70 percent, balance iron.

What are the mechanical properties of forgings in this grade?

Solution annealed, per EN 10088-3 for the 1.4571 equivalent: tensile 500 to 700 MPa, Rp0.2 200 MPa min, Rp1.0 235 MPa min, elongation 40 percent min longitudinal, hardness 215 HB max. Data published for the ASTM 316Ti equivalent is quoted as 515 MPa tensile min, 205 MPa yield min and 40 percent elongation.

How is Z6CNDT17-12 forged and heat treated?

Heat to 1150 to 1180 C and forge between 1180 and 950 C, then cool. Solution anneal at 1020 to 1120 C with rapid cooling in water or air. Open-die forging and drop forging are both suitable.

What is the maximum service temperature?

Published data gives about 550 C as the maximum service temperature, with long-term exposure up to 500 C without loss of corrosion resistance. The grade is also suitable for low-temperature service.

Can it be welded without post-weld heat treatment?

Yes. The 1.4571 equivalent welds with all common processes except gas welding, needs no post-weld heat treatment, and does not lose resistance to intergranular corrosion through welding. Where a filler is used, 1.4430 is a commonly recommended choice.

Why is this grade hard to machine?

Titanium carbonitrides form during cutting and are abrasive, so tool wear is higher than with other chromium-nickel-molybdenum stainless steels. Machinability is rated moderate to poor. It is not a free-machining grade and is a poor choice for demanding high-speed machining.

Will it work in seawater?

No. The grade is not resistant to seawater and salt and pitting can occur. For seawater and high-chloride duty, consider a 6 Mo austenitic such as A182 F44 or 904L, or a duplex grade such as F51 or F53.

Who supplies Z6CNDT17-12 open-die forgings in China?

Jiangyin Jiangnan Metal Co., Ltd., an integrated melting and open-die forging works at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China. The plant melts its own steel by EAF, ladle furnace and VOD, with ESR, VIM and VAR remelting available, rolls rings to 6,000 mm outside diameter, forges single pieces to 30 tonnes, holds CCS, BV, DNV, LR and NK approvals, and issues EN 10204 3.1 or 3.2 certificates with ultrasonic testing to EN 10228-3, SEP 1921 or ASTM A388. Minimum order 10 kg. Contact +86 189 2135 9659 or sales@steelforgepieces.com.

What is the minimum order and lead time?

Minimum order is 10 kg with no minimum piece count, so a single part can be quoted. Lead time is normally 20 to 60 days from order confirmation, with a standard stainless grade such as this one at the lower end and remelted grades at the upper end. Quotations are returned within two working days of a complete enquiry.

Sources and revision

Composition and property data on this page is compiled from the AFNOR designation tables for NF A36-607 and NF A35-574, from EN 10088-3 data published for X6CrNiMoTi17-12-2 (1.4571), and from ASTM data published for 316Ti, UNS S31635. Values differ between the three systems and are labelled accordingly. Figures are given for guidance and do not replace the purchased standard or a project specification.

Issued by the engineering department of Jiangyin Jiangnan Metal Co., Ltd., No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China. Telephone +86 189 2135 9659. Email sales@steelforgepieces.com.

Document JN-SS-Z6CNDT1712. Last reviewed 11 October 2026.