DOC GRADE DATA SHEET  /  STEEL X5CrNiMoCuNb14-5  /  NO 1.4594 REV 2026-10-10  /  +86 189 2135 9659  /  sales@steelforgepieces.com
Jiangnan Metal Open-Die Forging Works · Est. 1997 Request Quote

Home / Stainless Steel / X5CrNiMoCuNb14-5

Martensitic precipitation hardening stainless steel

X5CrNiMoCuNb14-5 Forgings EN 1.4594 · FV520B · BS S143 · rings, flanges, shafts and bars forged to drawing

Jiangyin Jiangnan Metal Co., Ltd. melts and forges X5CrNiMoCuNb14-5 at one works in Jiangyin, Jiangsu, China. The grade carries roughly 14 percent chromium and 5 percent nickel with molybdenum, copper and niobium, and takes its strength from copper-rich precipitates formed during ageing. Against 17-4PH it adds molybdenum, which buys better resistance to intergranular and pitting attack.

Rings roll to 6,000 mm outside diameter, single pieces run to 30 tonnes, and the smallest order we accept is 10 kg. Send a drawing or a cut list and we will price it.

Grade Record1.4594
EN name
X5CrNiMoCuNb14-5
EN number
1.4594
Also
FV520B · BS S143 · UNS S45000
Standard
EN 10088-3
Type
Martensitic, precipitation hardening
Conditions
AT · P930 · P1000 · P1070
Density
7.8 kg/dm³, magnetic
PREN
19
Melting
EF + LF + VOD, ESR on request
Max piece
30 t, rings to 6,000 mm OD
Lead time
20 to 60 days
01

Designations and cross-reference

One steel, several names, and the limits behind them are not identical. The EN document and the original Firth Vickers specification disagree on chromium, niobium, phosphorus and sulphur, so the governing document belongs on the purchase order rather than the grade name alone.

Designations for X5CrNiMoCuNb14-5
SystemDesignationNote
EN nameX5CrNiMoCuNb14-5Listed in EN 10088-3 among the standard precipitation hardening grades
EN number1.4594Steel number
Trade nameFV520BFirth Vickers Silver Fox 520B
BritishBS S143Aerospace specification
UNSS45000Widely quoted as the equivalent; some databases treat S45000 (Alloy 450, XM-25) as a close relative rather than an exact match, so confirm against the end specification
02

Chemical composition

Both ranges are shown because buyers work to both. Our melt shop aims chemistry at the forging it will become, so a restricted range inside either column can be agreed before the heat is tapped.

Composition, percent by weight
ElementEN 1.4594 to EN 10088-3FV520B stock range
Carbon, C0.070 max0.07 max
Silicon, Si0.70 max0.70 max
Manganese, Mn1.00 max1.00 max
Phosphorus, P0.040 max0.035 max
Sulphur, S0.015 max0.025 max
Chromium, Cr13.0 to 15.013.20 to 14.70
Nickel, Ni5.0 to 6.05.00 to 6.00
Molybdenum, Mo1.2 to 2.01.20 to 2.00
Copper, Cu1.2 to 2.01.20 to 2.00
Niobium, Nb0.15 to 0.600.20 to 0.70
Iron, FeBalance, 72.6 to 79.5Balance

Niobium raises yield strength. Copper drives the hardening reaction and helps acid resistance. Molybdenum is what separates this grade from 17-4PH.

03

Mechanical properties

EN 10088-3 recognises one annealed and three precipitation hardened conditions for 1.4594 up to 100 mm thick. Name the condition as well as the grade when ordering, because the same steel covers a 350 MPa span in proof strength.

EN 10088-3, thickness d up to 100 mm, minima unless stated
ConditionRp0.2, MPaRm, MPaElongation A, %Hardness HB max
AT, solution annealed—1200 max—360
P930720930 to 110015—
P10008601000 to 120010—
P107010001070 to 127010—

Hardness values are guidance only. For rods, only the tensile strength values apply.

Traditional FV520B conditions

Typical values, rolled bar, longitudinal
Supply condition0.2% proof, N/mm²Tensile, N/mm²Elongation % minHardness HBIzod J min
Primary hardened
1050 C + 2 h at 750-850 C
———293 to 341—
Double overaged
1050 C + 2 h at 750-850 C + 2 h at 550 C
800925 to 109015277 to 34154
Correction to earlier published data

Some circulated copies of this grade sheet print the second overage step as a repeat of 750 to 850 C. The supply condition is named 750-550 C: the second step is two hours at 550 C. Ageing twice in the same band does not produce the overaged structure the figures above describe.

Toughness holds up in the cold. Impact energy of 40 J or better is reported down to minus 70 C. Reported fatigue strength is 490 to 620 MPa and shear strength 620 to 700 MPa, with elongation at break across the common variants in the 11 to 17 percent band.

04

Physical properties

Typical physical data
PropertyValuePropertyValue
Density7.8 kg/dm³MagnetisableYes
Elastic modulus200 GPaShear modulus76 GPa
Poisson ratio0.28PREN19
Thermal conductivity16 W/m·KThermal expansion11 µm/m·K
Specific heat470 J/kg·KThermal diffusivity4.4 mm²/s
Solidus1410 CLiquidus1450 C
Max service, corrosion450 CMax service, mechanical820 C
Electrical conductivity2.2 % IACSLatent heat of fusion280 J/g
05

Corrosion, welding, machining

Corrosion

Useful resistance in modest environments, with behaviour closer to austenitic grades than to plain martensitics. Low rusting rate in marine and industrial atmospheres, and useful resistance to some acid conditions. Better against intergranular and pitting attack than 17-4PH.

Welding

Welds by standard techniques with matching consumables. Oxy-acetylene is not recommended, as the weld can pick up carbon. Set the procedure and any post-weld treatment with your consumable supplier, since welding interacts with the ageing condition.

Machining

Hard going, as with any high-strength precipitation hardening steel. Roughing in the solution annealed condition and ageing afterwards usually costs less overall. We can supply proof-machined or near-net forgings to cut the metal you have to remove.

Galling

FV520B is noted for anti-galling behaviour, which is why it turns up in stems, sleeves and sliding valve parts rather than only in highly stressed shafts.

Heat treatment

Heating rate, soak time and cooling all shift with the size and shape of the piece, the furnace, the quench medium and how fast the work can be transferred. Treat the cycles quoted above as a starting point and agree the final schedule for your section before cutting metal.

06

Where the grade is used

The documented service record for this steel is narrower than the catch-all lists often published for it. These are the applications the grade is actually specified for.

  • Pump shafts and impellers, and fans.
  • Valves, valve stems and hydraulic equipment in oil and gas service.
  • Fasteners where strength has to come with corrosion margin.
  • Petrochemical, marine and nuclear engineering components, including nuclear transport flasks.
  • Steam turbine blades and other aircraft components.
  • Medical devices, and pharmaceutical plant.
07

Forged products and plant

Most forging suppliers in China buy billet. This works starts at the furnace, so the certificate traces a 1.4594 part back to its melt number rather than stopping at a purchased bar of unknown origin.

Shapes we forge in 1.4594

  • Seamless rolled rings from a punched preform on the radial-axial mills, rectangular or contoured section, from 50 mm up to 6,000 mm outside diameter.
  • Forged rings by upset and punch, for sections outside the ring mill envelope and for work that needs heavy reduction instead of rolling.
  • Flanges, weld neck, blind, slip-on, socket weld, lap joint and long weld neck.
  • Shafts and spindles, including stepped, gear and eccentric shafts, turned to 14,000 mm length and vertically quenched in the 15 m well furnaces.
  • Discs, tube sheets and blocks, machined to 5,000 mm diameter and supplied proof-machined for volumetric inspection.
  • Sleeves, bushings and hollow cylinders, bored from solid forged blanks to 1,600 mm diameter by 10,000 mm.
  • Valve and wellhead parts, bodies, bonnets, blocks, stems, seat rings and nozzles.
  • Round, flat and square bars as feedstock for machined parts and tooling.

Relevant plant

Equipment used on this grade
StepEquipmentCapacity
MeltingElectric arc furnace with ladle furnace refining25 t EF, ladle furnaces at 25 t and 50 t
Vacuum refiningVacuum oxygen decarburisation, for stainless and low-carbon work30 t and 60 t
RemeltingProtective-atmosphere electroslag furnace, where cleanliness is specified3 t and 6 t
ForgingHydraulic open-die presses6,300 t, 4,000 t, 2,000 t
Ring rollingRadial-axial ring mills6 m, 3 m and 1 m
Heat treatment14 furnaces, car-bottom and well typeChambers to 8,000 mm long, wells 15,000 mm deep
MachiningVertical and horizontal lathes, CNC, deep-hole drillingSwing to 5,000 mm, length to 14,000 mm

Maximum heat size is 60 tonnes and the heaviest single forging is 30 tonnes. No forging, heat treatment or machining step is subcontracted. The works has run since 1997 and employs 460 people, including 9 senior engineers, 32 intermediate engineers and 140 technicians.

08

Testing and documents

Standard scope of inspection
ItemStandard or scope
Ultrasonic testingEN 10228-3, SEP 1921 or ASTM A388, to the class you specify
Chemical analysisPer heat, to EN 10088-3 or the document named on the order
Mechanical testingTensile, hardness and impact for the ordered condition
Surface NDTPenetrant or magnetic particle on request
CertificateEN 10204 3.1 mill certificate, or EN 10204 3.2 endorsed by a third party
Works approvalsCCS, BV, DNV, LR, NK
09

Ordering

Send these six things and you will get a price and a date rather than a request for more information.

  • Grade and governing document, for example X5CrNiMoCuNb14-5 to EN 10088-3, or FV520B to BS S143.
  • Drawing or finished and rough sizes. PDF, DWG and STEP all work.
  • Delivery condition: AT, P930, P1000, P1070, or double overaged.
  • Quantity and the date you need it on site.
  • NDT class and acceptance criteria.
  • Certificate type, EN 10204 3.1 or 3.2.

Quote a 1.4594 forging

Jiangyin Jiangnan Metal Co., Ltd., No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China. Minimum order 10 kg with no minimum piece count, lead time 20 to 60 days, export to North America, Europe, the Middle East and Asia-Pacific.

Send the enquiry

+86 189 2135 9659  ·  sales@steelforgepieces.com

10

Questions

What is X5CrNiMoCuNb14-5

Steel number 1.4594, a martensitic precipitation hardening stainless steel in EN 10088-3. It carries 13 to 15 percent chromium, 5 to 6 percent nickel, 1.2 to 2.0 percent molybdenum, 1.2 to 2.0 percent copper and 0.15 to 0.6 percent niobium, with carbon capped at 0.070 percent. Strength comes from copper-rich particles precipitating in a martensitic matrix during ageing.

Is it the same as FV520B

Yes. X5CrNiMoCuNb14-5 and 1.4594 are the EN name and number for FV520B, originally Firth Vickers Silver Fox 520B, also specified as BS S143, with UNS S45000 widely quoted as the equivalent. The limits are not word for word identical between documents, so name the one that governs your order.

How does it compare with 17-4PH

Both harden by copper precipitation in a martensitic matrix. 1.4594 adds 1.2 to 2.0 percent molybdenum, which 17-4PH does not have, and resists intergranular and pitting attack better, with behaviour compared to 304 where the rusting rate is low. 17-4PH is stocked more widely and generally costs less. Pick 1.4594 when you need corrosion margin alongside the strength.

What strength can I specify

Up to 100 mm thick, EN 10088-3 offers AT at 1200 MPa tensile maximum, P930 at 720 MPa proof and 930 to 1100 MPa tensile, P1000 at 860 MPa proof and 1000 to 1200 MPa tensile, and P1070 at 1000 MPa proof and 1070 to 1270 MPa tensile. The double overaged FV520B route typically gives 800 MPa proof, 925 to 1090 MPa tensile, 15 percent elongation and 54 J Izod on longitudinal rolled bar.

Can it be welded

Yes, by standard techniques with matching consumables. Skip oxy-acetylene, which risks carbon pick-up. Agree procedure and any post-weld treatment with your consumable supplier.

What sizes can you forge

Rings from 50 mm up to 6,000 mm outside diameter, shafts turned to 14,000 mm, discs and tube sheets machined to 5,000 mm diameter, bored cylinders to 1,600 mm by 10,000 mm, and single pieces up to 30 tonnes. Minimum order is 10 kg with no minimum piece count.

What does the certificate cover

Heat analysis, mechanical results for the ordered condition, and the ultrasonic report to EN 10228-3, SEP 1921 or ASTM A388. Issued as EN 10204 3.1, or 3.2 with third-party endorsement. Because the steel is melted here, the certificate traces back to the melt number.

11

Related grades

Sources

  • EN 10088-3, technical delivery conditions for semi-finished products, bars, rods, wire, sections and bright products, grade 1.4594, conditions AT, P930, P1000 and P1070.
  • British Stainless Steel Association, grade notes on FV520B and the tabulated EN 10088-3 properties for martensitic and precipitation hardening long products.
  • Published FV520B stockholder data for the composition range, double overaged properties, corrosion behaviour and welding guidance.
  • EN 10228-3, SEP 1921 and ASTM A388 for ultrasonic examination of forgings; EN 10204 for inspection documents.

Data is for guidance in material selection and is not a warranty of properties for a given component. What a forging achieves depends on section size, forging ratio and heat treatment, and belongs in the contract. Reviewed 10 October 2026.