Open-Die Forging Factory, Jiangyin, Jiangsu, China Tel 0086-189-2135-9659  |  sales@steelforgepieces.com
Jiangyin Jiangnan Metal Co., Ltd.Forged Rings, Flanges, Shafts, Discs Request a Quote
Home › Stainless Steel › X2CrNiMoCuN25-6-3

X2CrNiMoCuN25-6-3 (1.4507) Super Duplex Stainless Steel Forgings

Forged rings, seamless rolled rings, flanges, shafts, bars, discs, sleeves and tube sheets, made to drawing by Jiangyin Jiangnan Metal Co., Ltd.

X2CrNiMoCuN25-6-3, material number 1.4507, is a copper-bearing super duplex ferritic-austenitic stainless steel listed in EN 10088-1. At roughly 25 percent chromium, 6 to 8 percent nickel, 3 to 4 percent molybdenum with copper and nitrogen added, it holds about twice the proof strength of 300-series austenitic grades and resists chloride pitting, crevice attack and stress corrosion cracking. Copper also helps in sulphuric and phosphoric acid. Jiangyin Jiangnan Metal Co., Ltd. forges this grade to customer drawings from EAF plus VOD material, with ESR on request, solution annealed, ultrasonically tested and certified to EN 10204 3.1 or 3.2.

EN Number1.4507
TypeSuper Duplex
PRENabout 40
MeltingEAF+VOD / ESR
Forging Range1200 to 900 C
Sour Service28 HRC max

Designations and Cross-References

Cross-references for 1.4507 are not consistent between publishers, and the difference matters at the order stage. Metalcor cross-references 1.4507 to UNS S32520, Alloy F255, under the brand names URANUS 52N and Ferrinox 255. Virgamet lists 1.4507 against both UNS S32550, ASTM A182 grade F61 or Alloy 255, and UNS S32520, grade F59, and also gives SUS 329J4L, UR52N+ and X3CrNiMoCuN26-6-3-2 as related designations. Langley Alloys states that A182 F61 equates to UNS S32550, an approximation of Ferralium 255.

The chemistry windows behind these numbers are not the same. Nickel is the clearest case: EN 1.4507 calls for 6.0 to 8.0 percent, while UNS S32550 allows 4.5 to 6.5 percent. State the standard and UNS number you need on the enquiry and we will melt and certify to it.

Table 1. Chemical composition, weight percent. Single figures are maxima.
Standard / GradeCSiMnPSCrNiMoCuN
EN 1.4507
X2CrNiMoCuN25-6-3
0.030.702.000.0350.01524.0-26.06.0-8.03.0-4.01.0-2.50.20-0.30
UNS S32550
ASTM A182 F61
0.041.001.500.0400.03024.0-27.04.5-6.52.9-3.91.5-2.50.10-0.25
UNS S32520
ASTM A182 F59
0.030.801.500.0350.02024.0-26.05.5-8.03.0-5.00.5-3.00.20-0.35
JIS SUS 329J4L0.031.001.500.0400.03024.0-26.05.5-7.52.5-3.5not specified0.08-0.30

Balance iron. Ranges per EN 10088 and the ASTM and JIS cross-reference tables published by Metalcor and Virgamet. PREN = %Cr + 3.3 x %Mo + 16 x %N. Nickel Systems lists PREN 40 for S32550, Ferralium 255, against 36 for 2205 duplex and 41 for S32760 Zeron 100.

Mechanical Properties

Table 2. Room temperature properties, solution annealed condition
PropertyValueMetric
Tensile strength, min110 ksi760 N/mm²
0.2 percent proof stress, min80 ksi550 N/mm²
Elongation, min15 percent15 percent
Charpy V-notch at -46 C33 ft-lbf45 J
Hardness for sour service28 HRC max per NACE MR0175
Density7.8 g/cm³

Values are those we supply against for this grade. Minima vary with product form, section size and the edition of the governing standard, so confirm against your specification before ordering. Actual results are reported on the EN 10204 certificate.

Forging and Heat Treatment

Hot working runs between 1200 and 900 degrees Celsius. After forging, parts are solution annealed at 1020 to 1100 degrees Celsius and quenched quickly. Slow cooling through the critical range lets sigma and other intermetallic phases form, which cuts toughness and corrosion resistance, so quench rate is controlled and recorded on every batch.

1.4507 appears in EN 10088-2 for flat products and EN 10088-3 for bars, rods, sections and bright products. EN 10250-4 covers open steel die forgings in stainless steel for general engineering purposes. Machining follows 300-series practice, allowing for higher strength and work hardening: rigid setups, positive rake tooling, heavy feeds at reduced surface speed, and plenty of coolant.

Forged Products We Make in This Grade

Where It Is Used

Offshore Oil and Gas

Subsea and deepwater production systems, risers, manifolds, seawater and firewater pipework, pressure vessels, downhole parts.

Chemical Processing

Phosphoric, sulphuric and nitric acid plant, reactors, heat exchanger and separator parts, pumps, valves, shafts.

Desalination

High pressure reverse osmosis plant, seawater piping, pump casings and shafts in chloride-bearing water.

Power and FGD

Flue gas desulphurisation equipment, power generation hardware, corrosion-resistant structural parts.

Pulp, Paper and Mining

Abrasive slurry service, metallurgical and mineral processing equipment, waste water plant.

Rotating Equipment

Gearboxes, turbines, gas compressors, air and nitrogen generators, transmission shafts and gear blanks.

Testing and Certification

Frequently Asked Questions

What is X2CrNiMoCuN25-6-3?
A copper-bearing super duplex ferritic-austenitic stainless steel, EN material number 1.4507, listed in EN 10088-1. The EN composition runs 24.0 to 26.0 percent chromium, 6.0 to 8.0 percent nickel, 3.0 to 4.0 percent molybdenum, 1.0 to 2.5 percent copper and 0.20 to 0.30 percent nitrogen.
What is the UNS equivalent of 1.4507?
Metalcor cross-references 1.4507 to UNS S32520, Alloy F255, sold as URANUS 52N and Ferrinox 255. Virgamet lists both UNS S32550, A182 grade F61 or Alloy 255, and UNS S32520, grade F59. The chemistry windows differ, most visibly in nickel, so give the exact UNS number and standard on the order.
What is the PREN of this grade?
Nickel Systems publishes a PREN of 40 for UNS S32550, Ferralium 255, against 36 for 2205 duplex and 41 for S32760 Zeron 100. PREN is percent Cr plus 3.3 times percent Mo plus 16 times percent N. A value at or above 40 is the usual threshold for super duplex.
What solution annealing temperature applies?
1020 to 1100 degrees Celsius followed by rapid quenching, per Virgamet data for 1.4507 and S32550. Hot forging and rolling is done between 1200 and 900 degrees Celsius. Quenching fast enough to avoid sigma phase is what keeps toughness and corrosion resistance.
Can you supply to NACE MR0175?
Yes. Supply hardness is held to 28 HRC maximum, ultrasonic testing is to EN 10228-3, SEP 1921 or ASTM A388, and certification is EN 10204 3.1 or 3.2.
What sizes and quantities do you take?
We work from customer drawings on open-die forgings and seamless rolled rings. Send the drawing, grade, governing standard, quantity and NDT requirement to sales@steelforgepieces.com and we will come back with feasible size, weight, lead time and price.
How is a price obtained?
Forgings in this grade are made to order, so there is no list price. Price depends on finished weight, input bar or ingot size, machining allowance, heat treatment, NDT class and certification level. Send a drawing and we will quote within one working day.

Related Grades

Request a Quotation

Send a drawing or dimensions and we will quote within one working day. Direct from the forging shop.

Jiangyin Jiangnan Metal Co., Ltd., Open-Die Forging Factory
No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Tel 0086-189-2135-9659  |  sales@steelforgepieces.com

Email Your Drawing Call the Factory

Data compiled from EN 10088-1, EN 10088-2, EN 10088-3, EN 10250-4, ASTM A182 and published grade datasheets. Given for guidance and not as a warranty. Order-specific results appear on the EN 10204 certificate. Reviewed October 2026.