Open-die forging factory, Jiangyin, Jiangsu, China Tel +86-189-2135-9659  |  sales@steelforgepieces.com
Jiangyin Jiangnan Metal Co., Ltd. Forged bars, rolled rings, hollow bars, discs and blocks

X2CrMoTi18-2 Forgings, EN 1.4521 / AISI 444 / UNS S44400

Forged round, square, flat and hexagonal bar, hollow bar, sleeve, bush, cylinder and shell, forged and seamless rolled rings, discs, blocks and plates, all made to drawing at our works in Jiangyin, China.

Datasheet reviewed 9 October 2026. Values are taken from published grade datasheets listed under references.

Grade at a glance

X2CrMoTi18-2 (EN material number 1.4521) is a low carbon ferritic chromium stainless steel with molybdenum added. Chromium runs 17 to 20 %, molybdenum 1.80 to 2.50 %, carbon is held at 0.025 % maximum and the structure is stabilized with titanium. It contains no nickel and is the European equivalent of AISI 444, UNS S44400 and JIS SUS444. Corrosion resistance is quoted as equal to 1.4401 and 1.4404 (316 and 316L), with excellent resistance to chloride stress corrosion cracking. Annealed proof strength is 320 N/mm² minimum with tensile 450 to 650 N/mm², the steel is magnetizable, and it is forged from 1050 down to 750 °C and annealed at 750 to 900 °C.

  • EN 1.4521
  • EN name X2CrMoTi18-2
  • AISI 444
  • UNS S44400
  • JIS SUS444
  • Structure ferritic
  • Nickel none
  • Magnetic yes

1. Designations and equivalent grades

Table 1. International designations for X2CrMoTi18-2. Source: Metalcor and Virgamet datasheets.
SystemDesignationRemark
EN, Europe1.4521, X2CrMoTi18-2Listed in EN 10088-2 and EN 10028-7
AISI / SAE, USA444
UNS, USAS44400, also listed as S44401S44401 covers the Ti and Nb stabilized variant
JIS, JapanSUS444
China019Cr19Mo2NbTi, 00Cr18Mo2Current and former designations
SS, Sweden2326
UNE, SpainF-3123
NF, FranceZ3CDT18-02, Z3CDFT18-02
STAS, Romania2TiMoCr180
Mill nameSupra 444/4521Outokumpu trade name for the grade
Related, not interchangeable1.4523 (X2CrMoTiS18), 1.4605 (X2CrAlTi18-2)1.4523 carries 0.15 to 0.35 % sulphur for machinability, 1.4605 is aluminium stabilized without molybdenum

2. Chemical composition

Table 2. Composition in per cent by mass. EN row from Metalcor and Virgamet, AISI row from the UNS S44401 limits quoted by Virgamet, JIS row from Virgamet.
SpecificationCSiMn PSCrMo NTi
EN 1.4521 max 0.025max 1.00max 1.00max 0.040max 0.015 17.0 to 20.01.80 to 2.50max 0.0300.15 to 0.80, to 4 x (C + N) + 0.15
AISI 444, S44400 / S44401 max 0.030max 1.00max 0.50max 0.040max 0.030 17.5 to 19.51.75 to 2.50max 0.035Ti and Nb stabilized
JIS SUS444 max 0.025max 1.00max 1.00max 0.040max 0.030 17.0 to 20.01.75 to 2.50max 0.025stabilized
Typical mill analysis 0.02 182Nb and Ti

Balance iron. Using both titanium and niobium gives a fully stabilized ferritic structure at a lower titanium level, which helps surface quality on the finished part.

3. Mechanical properties, annealed

Table 3. Room temperature values in the annealed condition. EN 10088-2 rows as published in the Outokumpu Supra range datasheet, supplier row from Metalcor.
Basis and product formRp0.2 (N/mm²)Rm (N/mm²)Elongation
EN 10088-2, cold rolled coil and sheetmin 320420 to 640A80 min 20 %
EN 10088-2, hot rolled coil and sheetmin 300400 to 600A80 min 20 %
EN 10088-2, quarto platemin 300420 to 620A min 20 %
Supplier datasheet value, Metalcormin 320450 to 650A5 min 20 %
Hardnessmax 200 HB30 (Metalcor), max 185 HB (Virgamet)
Modulus of elasticity at 20 °C220 kN/mm²

Ferritic grades of this type carry higher proof strength than the common austenitics while keeping elongation around 20 %. Properties actually achieved in a forging depend on section size, forging reduction, test position and the annealing cycle, so the acceptance values are fixed on the order rather than taken from flat product tables.

4. Physical properties at 20 °C

Table 4. Physical properties. Source: Metalcor datasheet 1.4521.
PropertyValue
Density7.7 g/cm³
Modulus of elasticity220 kN/mm²
Specific heat capacity430 J/(kg K)
Thermal conductivity23 W/(m K)
Electrical resistivity0.8 Ω mm²/m
MagnetizableYes, ferritic structure

5. Corrosion behaviour

The combination of 18 % chromium with 2 % molybdenum is what lifts this grade above the plain 17 % chromium ferritics. Metalcor records corrosion resistance equal to 1.4401 and 1.4404, the 316 and 316L austenitics, together with excellent resistance to stress corrosion cracking caused by chlorides. Outokumpu describes resistance to localized corrosion as close to the 1.4401 acid proof austenitic for its 18 % chromium, 2 % molybdenum ferritic product. Taking the pitting resistance equivalent in its usual form, Cr + 3.3 Mo, the typical analysis of 18 % chromium and 2 % molybdenum gives roughly 25.

In chloride bearing solutions pitting and crevice attack are still possible, and the outcome depends on chloride concentration, temperature, pH, redox potential and crevice geometry. Service life is usually decided by details rather than by the grade alone: avoid stagnant crevices in the design, pickle or mechanically clean weld and forging scale, and clean the surface at intervals where the duty allows it.

The practical argument for choosing 1.4521 over 304 or 316 is the resistance to chloride stress corrosion cracking, which is the failure mode that restricts austenitic grades in warm chloride service, together with the absence of nickel.

6. Forging and heat treatment

Table 5. Working and heat treatment data for 1.4521. Source: Virgamet datasheet.
OperationTemperatureCooling
Open-die forging1050 down to 750 °CWater, air or gas
Hot rolling1050 down to 750 °CWater, air or gas
Annealing750 to 900 °CAir or gas, furnace cooling only in special cases
HardeningNot possible, ferritic grade, strength comes from composition and the annealed condition

Our route for this grade

Certified billet or ingot with stabilized chemistry is soaked, then upset and drawn inside the 1050 to 750 °C window on our hydraulic presses, or ring rolled where the item is a ring. Work is reheated rather than finished below the bottom of the range, and time at the top of the range is kept short because ferritic steels coarsen if held hot. The piece is then annealed between 750 and 900 °C with air or gas cooling, rough machined, and checked for dimensions, chemistry by spectro or PMI, hardness and tensile properties. Certification is EN 10204 3.1 as standard. Ultrasonic testing, dye penetrant, extra tensile positions, impact testing and third party inspection by SGS, BV or TUV are added when the order calls for them.

7. Welding, machining and forming

Welding

Metalcor gives filler metal 1.4430, the 316L type, as suitable for this grade. Keep heat input low, use clean inert shielding, and remove weld oxide by pickling or mechanical cleaning so that the passive film reforms. Expect lower ductility across the weld than in the parent metal, and treat heavy sections with more care than thin ones.

Machining

The grade work hardens far less than the austenitics, so chip control and tool life are more predictable. Use sharp tooling, a rigid set-up and plenty of coolant. Where free cutting behaviour matters more than corrosion performance, 1.4523 is the sulphur bearing relative, but it should not be substituted without agreement because sulphur lowers corrosion resistance.

Cold forming

Stabilized 18 % chromium ferritics bend, fold and draw well, and Outokumpu describes its 444/4521 product as having excellent deep drawability. On forged items this matters mainly for downstream operations such as flaring or swaging on hollow bar.

8. Where the grade is used

Metalcor lists cold heading parts and heat exchanger tubes as the applications for 1.4521, and the grade is supplied by mills mainly as sheet, plate, tube and fittings. Wider literature for the 18 % chromium, 2 % molybdenum ferritic covers hot water tanks and water heaters, heat exchangers, boiler and flue components, solar water heating, and pipework for water service. In forged form we most often make valve and pump parts, flange and ring blanks, tube sheet hardware, sleeves and shafts for hot water and brackish water duty, and nickel free parts for customers who have specified the grade to avoid chloride stress corrosion cracking.

One point worth raising early in an enquiry: potable water approvals such as the German DVGW or Swiss SVGW marks are granted to a named manufacturer for a named product and production route, never to a steel grade in general. If your project needs a specific approval, tell us at enquiry stage and we will confirm in writing what certification can be supplied with the forged item.

9. Forged product forms

Table 6. Open-die forged forms supplied in EN 1.4521 / AISI 444. Confirm the size range for your item at enquiry.
FormCoversUsual condition
BarRound bar and rod, square, rectangular, flat and hexagonal barAnnealed, black or rough turned, cut to length
Hollow sectionsHollow bar, sleeve, bush, cylinder, barrel, casing, shell, hub, housing, pipe and tube blanksAnnealed, bored and rough machined
RingsForged rings, seamless rolled rings, flange blanks, wear and retaining ringsAnnealed, faces rough machined
Discs and blocksDiscs, blanks, blocks, plates, slabs, stepped shaftsAnnealed, saw cut or rough machined
To drawingShafts, stems, bodies, bonnets, tube sheets, near net shapesAs specified on the drawing

10. Standards and basis of supply

The grade appears in EN 10088-2 for sheet, plate and strip and in EN 10028-7 for stainless flat products for pressure purposes, and as Type 444 UNS S44400 in ASTM A240. Because the published product forms are flat products, tube and fittings, forged bars, rings and shaped parts in this grade are normally ordered against agreed technical delivery conditions: chemistry to EN 10088, plus the mechanical values, test positions, heat treatment condition and testing set by the purchaser, often framed by EN 10250-4 for stainless open-die forgings or by ASTM A182. We state the exact basis on the quotation and repeat it on the certificate so that nothing is open to argument at incoming inspection.

11. Questions we are asked

What is X2CrMoTi18-2?
The EN name for material 1.4521, a ferritic chromium stainless steel with molybdenum added. Carbon is 0.025 % maximum, chromium 17 to 20 %, molybdenum 1.80 to 2.50 %, titanium stabilized, no nickel. Equivalent to AISI 444, UNS S44400 and JIS SUS444.
Is it as corrosion resistant as 316?
Metalcor records corrosion resistance equal to 1.4401 and 1.4404 with excellent resistance to chloride stress corrosion cracking, and Outokumpu describes resistance to localized corrosion as close to the 1.4401 austenitic. It is not a substitute in every medium: strong mineral acids or high chloride concentrations call for a higher alloyed austenitic, duplex or super duplex grade.
What temperatures are used for forging and annealing?
Forging and hot rolling run from 1050 down to 750 °C with cooling in water, air or gas. Annealing is 750 to 900 °C, air or gas cooled, with furnace cooling only in special cases. The grade cannot be hardened by heat treatment.
Is it magnetic, and is there nickel in it?
It is magnetizable because the structure is ferritic, and it contains no nickel.
Which filler metal for welding?
Filler 1.4430, the 316L type, per the Metalcor datasheet. Keep heat input low and clean the weld afterwards. Welds have lower ductility than the parent material.
Will you make a single piece?
Yes. Open-die forging suits one offs and small batches as well as repeat quantities. Send the drawing with the grade, quantity, heat treatment condition and testing you need and we will quote.
What certification comes with the material?
EN 10204 3.1 as standard, showing heat number, chemical analysis, mechanical test results and heat treatment. Ultrasonic testing, PMI, dye penetrant, hardness survey, dimensional report and third party inspection are available when specified on the order.

12. Request a quotation

Send the drawing or specification for your X2CrMoTi18-2 bars, rings, hollow bars, discs or blocks and we will come back with price, forged weight and lead time.

Jiangyin Jiangnan Metal Co., Ltd., open-die forging factory

No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Tel, WhatsApp and WeChat +86-189-2135-9659
Email sales@steelforgepieces.com

Email an enquiry Contact page

References

  1. Metalcor GmbH, datasheet 1.4521 / AISI 444 / UNS S44400: designations, composition, mechanical and physical properties, filler metal, applications. metalcor.de
  2. Virgamet, 1.4521, X2CrMoTi18-2, AISI 444, UNS S44401: equivalent grades, composition comparison, hardness, forging and annealing data. virgamet.com
  3. Outokumpu, Supra range datasheet, Supra 444/4521 (EN 1.4521, UNS S44400), November 2022: EN 10088-2 strength values, corrosion comparison, formability. outokumpu.com
  4. Steelnumber, X2CrMoTi18-2 / 1.4521 to EN 10088-2. steelnumber.com
  5. EN 10088-2, EN 10028-7, EN 10250-4 and ASTM A240 for the governing delivery conditions.

Figures above are standard minima or typical datasheet values for the grade and are given for guidance. They are not a guarantee of the properties of a particular forging, which depend on section size, reduction, test position and heat treatment as agreed on the order. Check requirements against the specification that governs your application.