Open-die forging factory, Jiangyin, Jiangsu, China. EN 10204 3.1 and 3.2 certificates. Tel 0086-189-2135-9659  |  Email sales@steelforgepieces.com
Jiangyin Jiangnan Metal Co., Ltd. Open-die forgings, seamless rolled rings, forged flanges
Home › Stainless Steel › X2CrMnNiMoN26-5-4 (1.4467)

X2CrMnNiMoN26-5-4 (1.4467) Forgings

Duplex stainless open-die forged bars, seamless rolled rings, discs, shafts, hollow bars and valve bodies, made to drawing by Jiangyin Jiangnan Metal Co., Ltd.

X2CrMnNiMoN26-5-4 is a high-alloyed CrMnNiMoN stainless steel with the material number 1.4467, listed in the German Stahl-Eisen-Liste and grouped with the ferritic-austenitic (duplex) stainless steels. Part of the nickel normally used to stabilise austenite is replaced by manganese at 4.0 to 6.0 % and nitrogen at 0.30 to 0.45 %, so the grade reaches duplex alloying levels with only 3.5 to 4.5 % nickel.

Recorded applications are heat exchangers, propeller shafts, highly loaded components in urea plants, centrifugal separators, parts for petroleum extraction, turbine blades, low-pressure compressors and offshore equipment. Jiangyin Jiangnan Metal supplies the grade as open-die forgings and seamless rolled rings, ultrasonically tested and certified to EN 10204 3.1 or 3.2.

1. Designations and trade names

Designations recorded for X2CrMnNiMoN26-5-4
DesignationTypeRegister or holder
X2CrMnNiMoN26-5-4Steel nameStahl-Eisen-Liste
1.4467Material numberStahl-Eisen-Liste 2003, Germany
X 2 CrMnNiMoN 26 5 4Earlier written formStahl-Eisen-Liste 1990
X3CrMnNiMoN25-6-4Closely related gradeDIN cross-reference
BOEHLER A905Trade namevoestalpine BOEHLER Edelstahl
A905Trade nameSchoeller-Bleckmann Edelstahlrohr
BGH 4467Trade nameBGH Edelstahl Siegen GmbH

No established ASTM or UNS twin exists for this grade. Where a North American equivalent is needed, obtain written acceptance from the end user before any substitution.

2. Chemical composition of 1.4467

Specified chemical composition in mass %, balance iron
CSiMnPSCrNiMoN
max 0.03max 0.804.0 to 6.0max 0.030max 0.015 24.5 to 26.53.5 to 4.52.0 to 3.00.30 to 0.45

Using the formula PREN = %Cr + 3.3 x %Mo + 16 x %N, the composition limits above give a pitting resistance equivalent of roughly 36 at the low end and 44 at the high end. This is an arithmetic result from the specification range, not a guaranteed property. The actual value depends on the heat analysis, which is stated on the mill certificate supplied with every order.

3. Delivery condition and mechanical properties

As a duplex steel, 1.4467 develops its properties through solution annealing followed by rapid quenching, which dissolves intermetallic phases and sets the ferrite to austenite balance. Forgings are supplied solution annealed and quenched unless the order states otherwise.

Published mechanical data for this particular grade differs between open databases, and we do not quote figures we cannot stand behind. Guaranteed values for proof stress, tensile strength, elongation, impact energy and hardness are agreed order by order against the governing standard or your own specification, and are verified on test pieces taken from the forging in the delivery condition. As a family, duplex grades offer higher strength and better corrosion resistance than standard austenitic stainless steels, which is the main reason this grade is specified for loaded parts in aggressive media.

Delivery condition

Solution annealed and quenched. Black forged or rough machined as agreed.

Test location

Prolongation or sacrificial ring. Orientation to standard or to your drawing.

Optional testing

Ferrite content, intergranular corrosion, pitting to ASTM G48, low-temperature impact.

4. Forged product forms in X2CrMnNiMoN26-5-4

Open-die forged shapes available in 1.4467
FormDescription
BarsForged round bars and rods, square, rectangular, flat and hex bars.
Hollow forgingsHollow bars, sleeves, bushes and bushings, pipes, tubes, barrels, casings, shells, cylinders, hubs and housings.
RingsSeamless rolled rings and open-die forged rings.
Blocks and discsForged blocks, discs, disks and plates.
ShaftsMarine, ship and pump propeller shafts, shaftings, spindles, eccentric shafts, crankshafts.
Valve partsCheck, control, globe, gate, ball and plug valve bodies, valve blocks, stems and seat rings.
Rotating partsTurbine blades, gears, wheels, rolls, manifolds and nozzles.

5. Typical applications

The applications below are those recorded for 1.4467 in materials registers, matched against the forged parts we produce.

Heat exchangers

Tube sheets, forged flanges, shells and channel sections.

Marine and seawater

Propeller shafts, seawater and injection pump parts, desalination plant components.

Urea and chemical plant

Highly loaded urea plant components, reactor internals, pulp and paper plant parts.

Oil, gas and offshore

Valve blocks for offshore duty, subsea and deepwater production hardware, wellhead parts.

Rotating equipment

Turbine blades, low-pressure compressor parts, centrifugal separators.

Process industry

Pumps, mixers, pressure-retaining bodies and forged fittings.

6. Manufacturing and inspection route

Melting

Material for 1.4467 forgings is procured on an EAF plus VOD route, or ESR remelted where the part calls for tighter cleanliness and lower segregation. Nitrogen control matters in this grade, so the heat analysis is reviewed before forging is released.

Forging

Open-die forging on hydraulic presses with a controlled temperature window and a recorded total reduction ratio, followed by solution annealing and rapid quenching. Ring blanks are produced on a radial and axial rolling mill for seamless rolled rings.

Non-destructive testing

Ultrasonic testing to EN 10228-3, SEP 1921 or ASTM A388, to the quality class nominated on your order. Liquid penetrant, dimensional and visual inspection are standard. Positive material identification is available on request.

Certification

Each shipment is released with an inspection certificate to EN 10204 3.1, or EN 10204 3.2 witnessed by a third party such as TUV, BV, DNV, LR or SGS when this is specified at order stage.

Welding

Where welding is involved, 1.4467 is listed as a base material for 25 Cr super duplex rutile covered electrodes of the 2507 and E2594-16 type. Procedure qualification should be carried out on the actual heat and thickness.

7. Frequently asked questions

What is the material number of X2CrMnNiMoN26-5-4?

1.4467, as listed in the Stahl-Eisen-Liste. The grade is described there as a high-alloyed CrMnNiMoN stainless steel and is grouped with the ferritic-austenitic duplex steels.

Why does this grade contain so much manganese?

Manganese and nitrogen both stabilise austenite. Carrying 4.0 to 6.0 % manganese and 0.30 to 0.45 % nitrogen lets the grade hold a duplex ferrite and austenite structure at only 3.5 to 4.5 % nickel, instead of the higher nickel a conventional duplex would need.

Is 1.4467 the same as 2205 or 2507?

No. All three are duplex stainless steels, but the alloy balance is different, in particular much more manganese and less nickel in 1.4467. Do not substitute one for another without written approval from the design authority.

What sizes can you forge?

Bars, rings, discs and shafts are made to drawing. Send the finished dimensions, the machining allowance you want and the quantity, and we will confirm feasibility, forging weight and lead time.

What is the minimum order quantity?

We take single prototype forgings as well as series production. Since 1.4467 is a specialty grade, lead time is driven mainly by raw material availability, so allow time for heat procurement on a first order.

Can you supply machined parts?

Yes. Forgings can be supplied black, heat treated, rough machined to your sketch, or finish machined. The machining allowance is fixed on the forging drawing before production starts.

Quotation for X2CrMnNiMoN26-5-4 and 1.4467 forgings

Send your drawing, size list or specification. We reply with price, forging weight, test scope and lead time, normally within one working day.

8. Related duplex and corrosion-resistant grades

Buyers comparing X2CrMnNiMoN26-5-4 usually also look at A182 F51, A182 F53, A182 F55, A182 F61, A182 F44, 904L, Sanicro 28, Nitronic 50 and Nitronic 60. All are available from us as open-die forgings and seamless rolled rings.

Composition and designation data on this page are given for guidance. The governing documents for any supply are the order specification and the mill certificate issued with the goods. Page last reviewed .