GRADE DATA SHEET UNS S31700 / AISI 317 / 1.4449 FORGING SPEC ASTM A182 F317 REV 2026-10-05 MARKDOWN VERSION
Jiangnan Metal Open-Die Forging Works · Jiangyin, China Request quote

Austenitic stainless steel · 19Cr 13Ni 3.5Mo

UNS S31700 Forgings Rings, flanges, bars, discs, tube sheets and shafts to ASTM A182 F317

UNS S31700 is the austenitic stainless steel also designated AISI Type 317, SAE 30317 and Werkstoff 1.4449. It carries 18.0 to 20.0 % chromium, 11.0 to 15.0 % nickel and 3.0 to 4.0 % molybdenum with carbon held to 0.08 % max, making it a modified Type 316 with more chromium, nickel and molybdenum for higher strength and better resistance to chloride pitting.

Jiangyin Jiangnan Metal Co., Ltd. melts this grade on site through the electric arc furnace, ladle furnace and vacuum oxygen decarburisation route, then forges, heat treats, machines and tests it in the same works. Rings go to 6,000 mm outside diameter and single pieces to 30,000 kg.

Grade identificationS31700
UNS
S31700
AISI
Type 317
Forging
ASTM A182 / ASME SA-182 F317
Werkstoff
1.4449
SAE
30317, J405 (30317)
Structure
Austenitic, non-hardenable by heat treatment
Anneal
1010–1121 °C (1850–2050 °F)
Melt route
EF → LF → VOD, ESR on request
Certification
EN 10204 3.1 or 3.2
01

Chemical composition

The limits below are the ASTM A182 grade F317 ranges for forgings, in weight percent. The same ranges apply in ASTM A240 for plate and ASTM A276 for bar, so one S31700 heat can cover forged, barred and plate items on a single job.

Table 1 — UNS S31700 composition, weight %
ElementSymbolASTM A182 F317 limitTypical
CarbonC0.08 max0.08
ChromiumCr18.0–20.019
NickelNi11.0–15.013
MolybdenumMo3.0–4.03.50
ManganeseMn2.00 max2
SiliconSi1.00 max1
PhosphorusP0.045 max0.045
SulfurS0.030 max0.030
IronFeBalance61

Limits: ASTM A182 grade symbol F317 (UNS S31700). Typical values: AZoM Grade 317 data sheet. Mill certificates state the actual heat analysis.

S31700 against S31703 (317L)

Both grades share the same chromium, nickel and molybdenum ranges. Carbon is the dividing line: 0.08 % maximum for 317, and 0.03 % maximum for 317L. The lower carbon level in 317L holds back carbide precipitation in the weld heat-affected zone, which is why welded vessels and scrubber internals are usually specified in 317L, while 317 keeps a modest strength advantage. If the part will be welded into a corrosive service, raise it with us before the heat is booked, because the choice has to be made at the melt stage and not afterwards.

02

Mechanical properties

Two different sets of figures are in circulation for this grade and they are not interchangeable. The specified minimums are what a forging has to reach to be accepted to ASTM A182 F317. The typical column is what annealed material normally tests at. Buy to the minimums, expect the typicals.

Table 2 — Specified minimums against typical annealed values
PropertyASTM A182 F317 minimumTypical, annealed
Tensile strength515 MPa / 75 ksi620 MPa / 89,900 psi
Yield strength, 0.2 % offset205 MPa / 30 ksi275 MPa / 39,900 psi
Elongation in 50 mm or 4D30 %45 %
Reduction of area50 %not stated
Hardness, Rockwell Bto order85 HRB
Modulus of elasticitynot specified193 GPa / 27,993 ksi
Poisson's rationot specified0.27–0.30

Minimums: ASTM A182 / A182M grade F317. Typical annealed values: AZoM Grade 317 data sheet. Heavy sections test lower than thin ones at the same chemistry, so agree the test location and acceptance values at enquiry stage.

Table 3 — Physical and thermal properties
PropertyMetricImperial
Density8.0 g/cm³0.289 lb/in³
Melting point1370 °C2550 °F
Thermal conductivity at 100 °C16.3 W/m·K113 BTU·in/hr·ft²·°F
Thermal expansion, 0–100 °C16 µm/m·°C8.89 µin/in·°F

Source: AZoM Grade 317 data sheet.

03

Designations and standards

S31700 runs through a long list of ASTM and ASME product specifications. Naming the right one on the purchase order matters, because the UNS number on its own fixes the chemistry but says nothing about heat treatment condition, testing or documentation.

Table 4 — Equivalent designations and product specifications
CategoryDesignation
UNSS31700
AISI / SAEType 317, SAE 30317, SAE J405 (30317)
GermanDIN / Werkstoff 1.4449
Forgings and forged fittingsASTM A182 grade F317, ASTM A403 and ASME SA403, ASTM A473
Bar, billet and wireASTM A276, ASTM A314, ASTM A479, ASTM A478, ASTM A580
Plate, sheet and stripASTM A240 and ASME SA240, ASTM A167
Pipe and tubeASTM A213, A249, A269, A312, A409, A511, A554, A632, A813, A814; ASME SA249, SA312, SA409
Military and federalQQ S763, MIL-S-862

Designation list: AZoM Grade 317 data sheet. Forging grade symbol F317 with its composition and property limits: ASTM A182.

04

Forging, heat treatment, machining and welding

Melting

Stainless grades at this works are melted in the electric arc furnace, refined in a ladle furnace and decarburised under vacuum, which is the route used where low carbon or tight nitrogen control is needed. Maximum heat size is 60 t. Protective-atmosphere electroslag remelting on the 3 t or 6 t furnace is available where a cleaner ingot, less segregation or better transverse properties are called for.

Hot working

Type 317 takes all the common hot working procedures. Working range is 1149 to 1260 °C (2100 to 2300 °F) and the steel should not be worked below 927 °C (1700 °F). Annealing after hot work restores corrosion resistance.

Heat treatment

Annealing is at 1010 to 1121 °C (1850 to 2050 °F) followed by cooling. The grade does not respond to hardening heat treatment, so strength above the annealed level can only come from cold work. Fourteen furnaces handle this in-house, including car-bottom furnaces with working chambers to 8,000 mm long and two pit furnaces 15,000 mm deep for vertical treatment of long shafts.

Cold working

Stamping, shearing, drawing and heading all work on this grade. Annealing after cold work brings internal stress down.

Machining

Type 317 is tougher than Type 304, so chip breakers are recommended. Avoid running constant feeds at low speed, which works the cut surface. On-site machining covers vertical turning to 5,000 mm swing, horizontal turning to 14,000 mm between centres, CNC turning and milling, and deep-hole drilling to 1,600 mm diameter by 10,000 mm.

Welding

Fusion and resistance welding both apply, using AWS E317, ER317 or 317L filler metal. Oxyacetylene welding is not recommended for this grade.

05

Corrosion behaviour

S31700 holds up in atmospheric exposure and in moderately oxidising and reducing conditions. The 3 to 4 % molybdenum, higher than Type 316 carries, is the main reason it resists pitting and crevice attack better than the standard chromium-nickel grades where chlorides are present.

In acid service, austenitic stainless steels of the 317 family are considerably more resistant than conventional chromium-nickel types to sulfuric acid solutions, and that resistance climbs with molybdenum content. ATI reports its 317L, 317LM and 317LMN grades as resistant to sulfuric acid up to 5 % concentration at temperatures as high as 49 °C, with better behaviour still below 38 °C.

Every austenitic grade loses ground as chloride concentration and temperature rise together. Where a scrubber, brine or high-chloride duty sits beyond what 317 will carry, the honest answer is a duplex or super-austenitic grade rather than a thicker 317 section. The same works forges A182 F51, A182 F53, A182 F55, A182 F44, 904L and Sanicro 28, so tell us the service conditions and we will say which one fits.

06

Forged product forms

Each item is forged from one piece of steel melted in the same works. No welding, no casting, no bought-in billet of unknown origin. Supplied as-forged, proof-machined or finish-machined.

Seamless rolled rings

Rolled from a punched preform on radial-axial mills of 1 m, 3 m and 6 m. Rectangular or contoured section, to 6,000 mm outside diameter.

Forged rings

Upset and punched rings for sections outside the ring-mill envelope, retaining rings, gear ring blanks and valve seat rings. From 50 mm outside diameter.

Flanges

Weld neck, blind, slip-on, socket weld, lap joint, orifice, anchor, girth, swivel and long weld neck to ASME B16.5 and B16.47, covered by ASTM A182 F317.

Round bars and blocks

Round, flat and square bar for valve stems, fasteners and machined bodies, plus die and mould blocks.

Discs and tube sheets

Solid forged discs, tube sheets and covers for heat exchangers and pressure vessels, proof-machined for volumetric inspection. To 5,000 mm machined diameter.

Shafts and spindles

Stepped, gear, pinion and eccentric shafts, crankshafts, spindles and rolls, turned to 14,000 mm length.

Sleeves, bushings and cylinders

Hollow forged cylinders, sleeves, bushings and couplings bored from solid forged blanks, to 1,600 mm diameter by 10,000 mm.

Valve and wellhead parts

Bodies, bonnets, blocks, stems, seat rings, spools, nozzles and manifolds for ball, gate, globe, check and plug valves.

Typical service

Published application areas for Grade 317 are pulp and paper plant, textile processing and chemical equipment. In forged form the grade turns up in digesters, liquor tanks and paper machine parts, absorber towers, scrubbers, stack liners and recuperators, heat exchangers, boilers and pressure vessels, slurry tanks, pumps and valves, refinery and catalytic recovery systems, waste treatment and thermal oxidisers, and pharmaceutical and biochemical process equipment.

07

Size envelope

The limits below are set by specific machines on the floor, not by a general claim. The largest ring the mill can roll is 6,000 mm outside diameter, the largest press is 6,300 t and the heaviest single forging is 30 t.

Table 5 — Working envelope for UNS S31700 forgings
ProductLimitSet by
Seamless rolled ringsto OD 6,000 mm6 m radial-axial ring mill
Rings, smallfrom OD 50 mmUpset-and-punch route below ring-mill range
Shaftsto 14,000 mm turned lengthC61160 lathe; 15 m pit furnace for vertical quench
Discs, tube sheets, blocksto 5,000 mm dia5,000 mm vertical turning lathe
Bored cylinders and hollow shaftsto 1,600 mm dia × 10,000 mmCNC deep-hole drilling machine
Single piece weightto 30,000 kg60 t heat size, 6,300 t press
Minimum order10 kgNo minimum piece count
Lead time20 to 60 daysDepends on grade, section and heat treatment cycle
08

Testing and certification

Because the steel is melted here, the certificate traces a part back to its melt number instead of stopping at a purchased billet.

Ultrasonic examination follows the standard named on the order. For austenitic material the European standard is EN 10228-4, which sets out ultrasonic testing of austenitic and austenitic-ferritic stainless steel forgings; EN 10228-3 covers ferritic and martensitic forgings and does not apply to this grade. ASTM A388 covers contact pulse-echo examination of steel forgings by straight and angle beam techniques, including the distance-gain-size method.

Documents are issued as EN 10204 type 3.1, an inspection certificate of actual results from the lot supplied, signed by the works inspection department. Type 3.2 is available where an independent surveyor witnesses the testing and counter-signs the certificate. Positive material identification, dye penetrant examination, impact testing, intergranular corrosion testing to ASTM A262, hardness survey and dimensional reports can all be added. The works holds CCS, BV, DNV, LR and NK approvals.

09

Questions we are asked

What is UNS S31700 stainless steel?

UNS S31700 is the austenitic stainless steel also designated AISI Type 317, SAE 30317 and Werkstoff 1.4449. It contains 18.0 to 20.0 % chromium, 11.0 to 15.0 % nickel and 3.0 to 4.0 % molybdenum, with carbon held to 0.08 % maximum. It is a modified version of Type 316 carrying more chromium, nickel and molybdenum, which raises its strength and its resistance to pitting and crevice corrosion in chloride-bearing media. Forgings in this grade are ordered to ASTM A182 grade F317.

What are the ASTM A182 F317 minimum mechanical properties?

ASTM A182 grade F317 requires a minimum tensile strength of 515 MPa (75 ksi), minimum yield strength of 205 MPa (30 ksi), minimum elongation of 30 % in 50 mm or 4D, and minimum reduction of area of 50 %. Annealed material normally tests well above those figures, at around 620 MPa tensile, 275 MPa yield, 45 % elongation and 85 HRB.

What is the difference between 317 and 317L?

Chromium, nickel and molybdenum ranges are the same in both grades. The difference is carbon: Type 317 (UNS S31700) permits up to 0.08 %, while Type 317L (UNS S31703) is limited to 0.03 % maximum. Lower carbon reduces carbide precipitation in the weld heat-affected zone, so 317L is usually chosen for welded fabrication, while 317 keeps a small strength advantage.

How is UNS S31700 heat treated?

Annealing is at 1010 to 1121 °C (1850 to 2050 °F) followed by cooling. The grade does not respond to hardening heat treatment and can only be hardened by cold work. Hot working runs at 1149 to 1260 °C (2100 to 2300 °F) and should not continue below 927 °C (1700 °F), with annealing afterwards to restore corrosion resistance.

Can UNS S31700 be welded?

Yes. Type 317 is welded by fusion and resistance methods using AWS E317, ER317 or 317L filler metal. Oxyacetylene welding is not recommended for this grade.

What size UNS S31700 forgings can you produce?

Rings roll to 6,000 mm outside diameter on the 6 m radial-axial mill, presses go to 6,300 t, and single pieces reach 30,000 kg from heats up to 60 t. Shafts turn to 14,000 mm, discs and tube sheets machine to 5,000 mm diameter, and hollows bore to 1,600 mm diameter by 10,000 mm long. Minimum order is 10 kg with no minimum piece count, and normal lead time is 20 to 60 days.

What testing and certification come with the forgings?

Forgings are ultrasonically examined to the standard named on the order, normally ASTM A388 or EN 10228-4 for austenitic stainless steel. Documents are issued as EN 10204 type 3.1 inspection certificates, or type 3.2 where an independent surveyor witnesses testing and counter-signs. The works holds CCS, BV, DNV, LR and NK approvals.

Where is UNS S31700 used?

Published application areas for Grade 317 are pulp and paper plant, textile processing and chemical equipment. In forged form the grade is used for absorber towers, scrubbers and stack liners, heat exchangers and pressure vessels, digesters and liquor tanks, valve bodies, bonnets, stems and seat rings, slurry tanks, pumps and nozzles.

How do I get a price for UNS S31700 forgings?

Price depends on the drawing, the finished weight and the quantity, so there is no list price for this grade. Send a drawing or the finished dimensions, the specification such as ASTM A182 F317, the quantity and any testing or certification requirements to sales@steelforgepieces.com, or call +86 189 2135 9659.

10

Ask for a price

Send a drawing and we will quote the process route, heat treatment, testing, lead time and price. Where there is no drawing yet, outside diameter, inside diameter, length or thickness and approximate finished weight are enough for a first figure.

  1. Drawing or finished dimensions, with machining allowance if you want it proof-machined.
  2. Specification, for example ASTM A182 F317, and the delivery condition.
  3. Quantity and required delivery date.
  4. Testing and documentation: ultrasonic standard and acceptance class, EN 10204 3.1 or 3.2, any PMI, PT or corrosion testing.

sales@steelforgepieces.com   +86 189 2135 9659

Jiangyin Jiangnan Metal Co., Ltd., No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China.