Home / Stainless steel / SUS 317
Material datasheet · Austenitic stainless steel
SUS 317 Forgings AISI 317 · UNS S31700 · EN 1.4449 · ASTM A182 F317
SUS 317 is a molybdenum-bearing austenitic stainless steel, in effect a higher chromium, nickel and molybdenum version of 316. It contains 18.0 to 20.0 percent chromium, 11.0 to 15.0 percent nickel and 3.0 to 4.0 percent molybdenum, with carbon held to 0.08 percent maximum. The extra molybdenum is what the grade is bought for: it raises strength and improves resistance to pitting and crevice attack in chloride-bearing, moderately oxidising and reducing media, so 317 goes in where 316 is marginal.
This works forges the grade to drawing rather than to a stock list. Steel is melted on site, forged or ring-rolled, solution annealed, machined and tested without leaving the plant, so the certificate traces back to a melt number instead of stopping at a purchased billet.
- Type
- Austenitic
- UNS
- S31700
- Forging spec
- ASTM A182 / SA182 F317
- EN number
- 1.4449
- Key element
- Molybdenum 3.0–4.0 %
- Anneal
- 1010–1121 °C, then cool
- Hot work
- 1149–1260 °C
- Max ring OD
- 6,000 mm
- Max piece
- 30 t
- Minimum order
- 10 kg, no piece minimum
- Lead time
- 20 to 60 days
- Certificate
- EN 10204 3.1, or 3.2 witnessed
Chemical composition
The limits below are the ASTM A182 Grade F317 forging requirement. Chemistry is read at the furnace on a mobile optical emission spectrometer and confirmed on the finished part with a handheld analyser, so the analysis printed on the certificate is this plant's own rather than a supplier's.
| Element | Symbol | Specified | Nominal |
|---|---|---|---|
| Carbon | C | 0.08 max | – |
| Chromium | Cr | 18.0–20.0 | 19 |
| Nickel | Ni | 11.0–15.0 | 13 |
| Molybdenum | Mo | 3.0–4.0 | 3.5 |
| Manganese | Mn | 2.00 max | – |
| Silicon | Si | 1.00 max | – |
| Phosphorus | P | 0.045 max | – |
| Sulphur | S | 0.030 max | – |
| Iron | Fe | Balance | 61 |
Low-carbon 317L (UNS S31703) is available where post-weld sensitisation is a concern. State which of the two you need on the enquiry.
Mechanical properties
Two sets of numbers matter here and they are not interchangeable. The first is what a forging has to achieve on test to be certified. The second is what annealed material of this grade typically measures. Buyers write the first into the purchase order; the second is useful for early design estimates.
Specified minimums, ASTM A182 F317
| Property | Metric | Imperial |
|---|---|---|
| Tensile strength, min | 515 MPa | 75 ksi |
| Yield strength 0.2 % offset, min | 205 MPa | 30 ksi |
| Elongation in 50 mm or 4D, min | 30 % | 30 % |
| Reduction of area, min | 50 % | 50 % |
Typical annealed values
| Property | Value |
|---|---|
| Tensile strength | 620 MPa |
| Yield strength | 275 MPa |
| Elastic modulus | 193 GPa |
| Poisson's ratio | 0.27 to 0.30 |
| Elongation at break, 50 mm | 45 % |
| Hardness, Rockwell B | 85 |
Typical values are not acceptance criteria. Results shift with section size, forging reduction and where the test piece is cut. Tensile testing here runs on 600 kN and 300 kN machines to ASTM A370 and ISO 6892.
Physical properties
| Property | Metric | Imperial |
|---|---|---|
| Density | 8.0 g/cm³ | 0.289 lb/in³ |
| Melting point | 1370 °C | 2550 °F |
Forging and heat treatment route
SUS 317 takes all the common hot-working methods. Stock is heated to 1149 to 1260 °C and the pass schedule is planned so the workpiece is off the press before it drops below 927 °C. Working colder risks cracking and leaves residual strain that costs corrosion resistance later.
After forging or ring rolling, parts are solution annealed at 1010 to 1121 °C and cooled. That step returns carbides to solution and restores the corrosion performance the grade was specified for, so it is not optional on anything going into chloride service. The grade does not respond to hardening heat treatment. Strength above the annealed condition can only come from cold work, and cold-worked parts should be annealed afterwards to relieve internal stress.
Machining is tougher going than on 304. Chip breakers help, and a constant feed at moderate speed works better than running slow. Discs and tube sheets are supplied proof-machined so the ultrasonic probe sits on a clean surface.
Melting
Electric arc furnace with ladle refining and vacuum oxygen decarburisation, which is the route that holds carbon down in a grade capped at 0.08 percent. Heats to 60 t.
Forging
Hydraulic presses at 6,300 t, 4,000 t and 2,000 t, five hammers from 750 kg to 5 t, and radial-axial ring mills at 1 m, 3 m and 6 m.
Heat treatment
14 furnaces, including car-bottom chambers to 8,000 by 2,000 by 2,000 mm and two 15 m well-type furnaces for quenching long shafts vertically.
Machining
Vertical lathes to 5,000 mm swing, horizontal lathes to 14 m between centres, CNC deep-hole drilling to 1,600 by 10,000 mm.
Product forms in SUS 317
Everything is made to drawing or to a stated rough size. There is no catalogue of fixed dimensions and no minimum piece count: the floor is 10 kg by weight.
| Form | Covers | Size limit |
|---|---|---|
| Seamless rolled rings | Rectangular and contoured section, gear ring blanks, slewing rings, bearing races | OD 50 to 6,000 mm |
| Forged rings | Upset and punched rings, retaining rings, valve seat rings | Outside the ring-mill envelope |
| Flanges | Weld neck, blind, slip-on, socket weld, lap joint, orifice, long weld neck | To ASME B16.5 and B16.47 |
| Bars and blocks | Round, flat and square bar, blanks for machined valve bodies | Press and lathe limits |
| Discs and tube sheets | Solid discs, tube sheets, covers, hubs, proof-machined for ultrasonic testing | To 5,000 mm machined diameter |
| Shafts and spindles | Stepped shafts, eccentric shafts, spindles, rolls, pinions | To 14,000 mm turned length |
| Cylinders and sleeves | Bored hollows, sleeves, bushings, nozzles, heavy-wall pipe sections | To 1,600 by 10,000 mm bored |
| Valve parts | Bodies, bonnets, stems, seat rings, blocks, manifolds | To drawing |
Heaviest single piece in any of these forms is 30 t, set by the 60 t heat size and the 6,300 t press.
Where the grade is used
317 is a pulp and paper, textile and chemical process grade before anything else. Common end uses for forged components in it fall into four groups.
Pulp and paper
Digesters, liquor tanks, paper machine components, and the flanges, tube sheets and valve parts that go with them. This is the classic home for the extra molybdenum.
Chemical process
Absorber towers, heat exchangers, pressure vessels, slurry tanks, stack liners and scrubber internals, where service is moderately oxidising or reducing and chloride is present.
Refining and recovery
Catalytic recovery systems, recuperators, and the forged pipe sections, tube sheets and flanges that go into them.
Valves and rotating parts
Bodies, stems and seat rings for ball, gate, globe, check and plug valves, plus shafts, gear blanks and spindles in power transmission duty.
Designations and product standards
SUS 317 is the Japanese-style designation for this grade. Orders are normally placed against the UNS number or the ASTM product specification, and that is what the certificate will reference.
| System or product form | Designation |
|---|---|
| UNS | S31700 |
| AISI / SAE | 317, SAE 30317 |
| EN / DIN | 1.4449 |
| Forgings and piping components | ASTM A182 / ASME SA182 F317 |
| Plate and sheet | ASTM A240 / ASME SA240 |
| Bar and shapes | ASTM A276, A473, A479 |
| Pipe and tube | ASTM A312, A213, A249, A269 |
| Fittings | ASTM A403 / ASME SA403 |
| Low-carbon variant | 317L, UNS S31703 |
Testing and certification
The works runs its own laboratory. A SUS 317 forging is released against a documented route: melt analysis, mechanical testing on a representative test piece, non-destructive examination, dimensional inspection, then certification.
| Stage | Method | Reference |
|---|---|---|
| Chemical analysis | Optical emission spectrometry, infrared carbon and sulphur | ASTM E415, ASTM E1019 |
| Alloy verification | Handheld analyser, positive material identification | PMI |
| Tensile | 600 kN and 300 kN universal testing machines | ASTM A370, ISO 6892 |
| Impact | Pendulum machine with low-temperature bath | ASTM A370 |
| Ultrasonic | Digital flaw detection on proof-machined surfaces | ASTM A388, EN 10228-3 |
| Magnetic particle | Where applicable to the component | ASTM E709 |
| Grain size | Metallography | ASTM E112 |
| Certificate | Mill test certificate, or witnessed by a third-party inspection body | EN 10204 3.1 / 3.2 |
Intergranular corrosion testing to ASTM A262 or G28 and pitting resistance to ASTM G48 are placed with an accredited outside laboratory and reported alongside the mill certificate. Ask at enquiry stage so they are scheduled before shipment rather than added afterwards.
Questions about this grade
What is SUS 317 stainless steel?
SUS 317 is the Japanese-style designation for the 317 molybdenum-bearing austenitic stainless steel, covered elsewhere as AISI 317, UNS S31700 and EN 1.4449. It runs 18.0 to 20.0 percent chromium, 11.0 to 15.0 percent nickel and 3.0 to 4.0 percent molybdenum with carbon at 0.08 percent maximum, which makes it a higher chromium, nickel and molybdenum version of 316 with more strength and better corrosion resistance.
How does SUS 317 differ from 316?
Molybdenum. SUS 317 carries 3.0 to 4.0 percent against roughly 2 to 3 percent in 316, with chromium and nickel also lifted. That extra molybdenum buys resistance to pitting and crevice attack in chloride-bearing and moderately reducing service, which is the reason the grade shows up in pulp and paper and scrubber duty where 316 is borderline. It costs more, so it is worth confirming the service genuinely needs it.
What does a SUS 317 forging have to test at?
Under ASTM A182 Grade F317 the minimums are 515 MPa tensile strength, 205 MPa yield strength, 30 percent elongation in 50 mm or 4D, and 50 percent reduction of area. Published typical values for annealed material sit above that at roughly 620 MPa tensile, 275 MPa yield, 45 percent elongation and Rockwell B 85, with an elastic modulus of 193 GPa. Write the specification minimums into the order, not the typical figures.
What are the forging and annealing temperatures?
Hot work between 1149 and 1260 °C, and stop before the piece falls below 927 °C. Solution anneal afterwards at 1010 to 1121 °C followed by cooling. The grade cannot be hardened by heat treatment, only by cold work, and cold-worked parts should be annealed to relieve stress.
How large a SUS 317 part can this works produce?
Seamless rings roll up to 6,000 mm outside diameter on the 6 m radial-axial mill, with 3 m and 1 m mills for smaller sizes. The heaviest single forging is 30 tonnes, worked on 6,300 t, 4,000 t and 2,000 t presses. Downstream equipment sets the practical limits: furnaces take work to 8,000 by 2,000 by 2,000 mm, two 15 m well furnaces allow long shafts to be quenched vertically, vertical lathes machine to 5,000 mm swing and horizontal lathes to 14 m between centres.
Is there a minimum order, and how long does it take?
Minimum order is 10 kg with no minimum piece count, so a single part is quotable. Lead time runs 20 to 60 days from order confirmation. SUS 317 sits at the lower end of that band because it is melted through the electric arc furnace and refined without a remelting step. Witnessed inspection or outside corrosion testing needs scheduling, so flag either at enquiry stage and it will be built into the quoted date.
Can 317L be supplied instead?
Yes. 317L, UNS S31703, is the low-carbon variant and is the usual choice where components will be welded and then exposed to aggressive service, since the lower carbon limits carbide precipitation at the weld. State which of the two you need on the enquiry, because the two are not interchangeable on a certificate.
Request a quotation
Quotations come from a drawing or a written specification. Sending the six items below in the first email removes a round trip and usually gets a price back within two working days.
| # | Item | Example |
|---|---|---|
| 1 | Grade or specification | ASTM A182 F317 / UNS S31700 |
| 2 | Dimensions, or a drawing in PDF, DWG, DXF or STEP | OD 1200 x ID 900 x H 260 mm |
| 3 | Quantity and expected repeat volume | 8 pcs, about 3 per year |
| 4 | Delivery condition | Proof-machined |
| 5 | Heat treatment and testing | Solution annealed, UT to ASTM A388 |
| 6 | Certification and destination port | EN 10204 3.2 witnessed, Rotterdam |