# Z7CND17-11-02

**AFNOR NF designation | EN equivalent X5CrNiMo17-12-2 (1.4401) | AISI 316**

Z7CND17-11-02 is the French AFNOR NF designation for a molybdenum-bearing austenitic
stainless steel. Jiangyin Jiangnan Metal Co., Ltd. forges it on open dies into seamless
rolled rings, flanges, discs, tubesheets, shafts and valve components, from 20 kg to
20 tonnes, to customer drawing.

Source page: https://www.steelforgepieces.com/Stainless-Steel/Z7CND17-11-02.html

## Key data

- **Designation:** Z7CND17-11-02, also written Z7CND17.11.02 or Z 7 CND 17-11-02.
- **Equivalents:** X5CrNiMo17-12-2 (1.4401), AISI 316 / UNS S31600, SUS316, 316S31, 0Cr17Ni12Mo2.
- **Chemistry:** Cr 16.0-18.0 %, Ni 10.0-14.0 %, Mo 2.0-3.0 %, C max 0.08 %, N max 0.10 %, balance iron.
- **Strength:** min 515 MPa tensile, 205 MPa yield at 0.2 % proof, 40 % elongation in 50 mm, solution annealed.
- **Reason for selection:** molybdenum raises pitting and crevice corrosion resistance in chloride service.
- **Supplied by:** Jiangyin Jiangnan Metal Co., Ltd., No.1 Chengxiqiao Road, Zhouzhuang Town,
  Jiangyin City, Jiangsu Province, China. Telephone +86 189 2135 9659.
  Email sales@steelforgepieces.com. EN 10204 3.1 certificate with every forging.

## What is Z7CND17-11-02 steel?

Z7CND17-11-02 is an austenitic stainless steel in the chromium-nickel-molybdenum family.
French drawings and older AFNOR-based specifications use this designation for the alloy
supplied elsewhere as 1.4401 or 316. Cross-reference tables place it alongside Z6CND17-11
and Z7CND17-12-02 as French counterparts of X5CrNiMo17-12-2.

The distinguishing element is molybdenum at 2 to 3 %. In 18/8 grades without molybdenum,
chlorides break down the passive film locally and start pits. Molybdenum stabilises that
film. It is the standard molybdenum-bearing austenitic grade, second in importance to
type 304.

### How the designation reads

The leading Z marks a highly alloyed stainless steel. The figure 7 gives carbon content in
hundredths of a percent. C, N and D stand for chromium, nickel and molybdenum, and 17-11-02
gives their nominal percentages. Total Materia lists the AFNOR grade with carbon at 0.07 %
maximum, while the 316-family limit in the table below is 0.08 % maximum. Where the purchase
order cites the French standard, the heat can be melted and certified to the 0.07 % cap.

### Forging practice

Melting is by EAF with VOD refining, and ESR where the order calls for it. Billet is heated
to about 1150-1260 C and finished above about 900-925 C. A reduction ratio of at least 3:1 is
held on critical sections. Forgings are solution annealed, rapidly cooled, and ultrasonically
inspected before machining.

## Chemical composition (mass %, balance iron)

| Element | C | Mn | Si | P | S | Cr | Mo | Ni | N |
|---|---|---|---|---|---|---|---|---|---|
| Minimum | - | - | - | - | - | 16.0 | 2.0 | 10.0 | - |
| Maximum | 0.08 | 2.0 | 0.75 | 0.045 | 0.03 | 18.0 | 3.00 | 14.0 | 0.10 |

Source: composition ranges published for the 316 grade to which Z7CND17-11-02 is
cross-referenced. Total Materia lists the AFNOR grade with C max 0.07 %. Composition is
verified on every heat and reported on the EN 10204 3.1 certificate.

## Mechanical properties, solution annealed

| Property | Value |
|---|---|
| Tensile strength Rm, minimum | 515 MPa |
| Yield strength Rp0.2, minimum | 205 MPa |
| Elongation in 50 mm, minimum | 40 % |
| Hardness, Rockwell B, maximum | 95 HRB |
| Hardness, Brinell, maximum | 217 HB |
| Typical tensile band, AFNOR grade | 530-740 MPa |
| Modulus of elasticity | 190-215 GPa |

Source: minima as specified for the 316 grade and matched by ASTM A182 F316, which requires
at least 515 MPa tensile and 205 MPa yield. Typical tensile band and modulus from Total
Materia for the AFNOR designation.

Wall thicknesses are driven by the 205 MPa proof figure rather than the 515 MPa ultimate.
The fully austenitic structure keeps toughness to cryogenic temperature.

## Physical properties, typical

| Property | Value |
|---|---|
| Density | 8000 kg/m3 |
| Elastic modulus | 193 GPa |
| Mean thermal expansion, 0-100 C | 15.9 micrometre/m.C |
| Mean thermal expansion, 0-538 C | 17.5 micrometre/m.C |
| Thermal conductivity at 100 C | 16.3 W/m.K |
| Thermal conductivity at 500 C | 21.5 W/m.K |
| Specific heat, 0-100 C | 500 J/kg.K |
| Electrical resistivity | 740 nano-ohm.m |
| Melting range | 1370-1400 C |
| Magnetic response, annealed | Very low permeability, fully austenitic |

Source: typical physical properties published for 316-grade stainless steel. Values are
typical rather than guaranteed minima and are not normally certified.

## International equivalents

| Country or standard | Designation |
|---|---|
| France, AFNOR NF | Z7CND17-11-02, also Z6CND17-11 and Z7CND17-12-02 |
| European Union, EN | X5CrNiMo17-12-2 |
| EN material number | 1.4401 |
| United States, AISI | 316 |
| United States, UNS | S31600 |
| Germany, DIN and WNr | X5CrNiMo17-12-2 |
| Japan, JIS | SUS316 |
| United Kingdom, BS | 316S31 |
| Italy, UNI | X5CrNiMo17-12 |
| China, GB | 0Cr17Ni12Mo2 |
| Sweden, SS | 2347 |
| Czechia, CSN | 17346 |
| Austria, ONORM | X5CrNiMo17-12-2KW |
| Russia, GOST | 08KH16N11M3 |

Source: cross-reference table for Z7CND17-11-02 and X5CrNiMo17-12-2 (1.4401) per the
European Steel and Alloy Grades database. UNS number per the 316 grade comparison published
by Atlas Steels. Cross-standard equivalence is never exact. Confirm acceptance against the
governing design code before substituting a grade in a pressure-retaining part.

## Heat treatment, corrosion and service limits

**Solution annealing.** The grade cannot be hardened by thermal treatment. Heat to about
1010-1120 C and cool rapidly. Total Materia quotes 1050-1125 C followed by air or water quench
for the AFNOR grade. The actual cycle used is stated on the certificate.

**Corrosion.** The pitting resistance equivalent number of type 316 is about 24, calculated as
%Cr + 3.3(%Mo) + 16(%N). The alloy is subject to pitting and crevice corrosion in warm
chlorides and to chloride stress corrosion cracking above about 60 C. It is not resistant to
warm seawater. For warm chloride duty consider 904L or a duplex grade.

**Elevated temperature.** Oxidation resistance is good in intermittent service to 870 C and
continuous service to 925 C. Continuous use in the 425-860 C band is not recommended where
aqueous corrosion resistance afterwards is required.

**Welding and machining.** Weldability by all standard fusion methods is good. Heavy welded
sections require post-weld annealing for maximum corrosion resistance. The alloy work-hardens
during machining, so positive rake, rigid setups and heavy feeds are required.

## Forged products manufactured

Rings and hollow bodies: seamless rolled rings, forged rings, retaining rings, sleeves,
bushes, bushings, forged pipe and tube, barrels, casings, shells, cylinders, hubs, housings,
hollow bars, bored blocks.

Discs, plates and bars: forged discs and disks, tubesheets and tube plates, forged round
bars, blanks, blocks, channel covers, forged gears and gear blanks.

Valve components: valve bodies, body blocks, bonnets, closures, stems, seat rings, and parts
for ball, gate, globe, check and plug valves.

Flanges and nozzles: forged flanges, girth and cover flanges, long welding neck nozzles,
nozzle necks, self-reinforced FVC nozzles, forged manifolds.

Rotating parts: forged shafts, eccentric shafts, spindles, crankshafts, rolls and wheels.

Heat-exchanger components: shell-and-tube exchanger parts, channel and shell sections,
tubesheets to drawing.

## Manufacturing range

| Parameter | Range |
|---|---|
| Outside diameter, rings and discs | 100-4,000 mm |
| Single-piece weight | 20 kg to 20 t |
| Length, shafts and bars | up to 8,000 mm |
| Melting route | EAF plus VOD, with ESR on request |
| Delivery condition | Solution annealed |
| Ultrasonic testing | EN 10228-3, SEP 1921 or ASTM A388 |
| Other NDT | Penetrant testing, hardness survey |
| Certification | EN 10204 3.1, or 3.2 with third-party witness |
| Machining | As-forged, rough-machined or finish-machined to drawing |
| Lead time, typical | 25-40 days after drawing approval |
| Pricing | Quoted per enquiry against customer drawing |

Magnetic particle testing is not applicable to a fully austenitic forging.

## Applications

Chemical and petrochemical processing: pressure vessels, tanks, heat exchangers, piping
systems, shafts and spindles.

Heat exchangers and refinery service: tubesheets, flanges, tubes, channel covers, catalytic
recovery systems, recuperators.

Valves and pipeline hardware: bodies, bonnets, stems, seat rings, strainer bodies. ASTM A182
F316 is the specification most often cited for these parts.

Offshore and onshore energy: bushings, sleeves, discs and housings for subsea and deepwater
production systems, air compressors, power generators, nitrogen generators.

Pulp, paper and food processing: digesters, liquor tanks, paper machine components, food
equipment and storage.

Power transmission: rings, spindles, bars and gear blanks for turbines, gas compressors and
gearboxes.

## Manufacturer

**Jiangyin Jiangnan Metal Co., Ltd.**
Open-die forging factory.
No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China.
Telephone: +86 189 2135 9659
Email: sales@steelforgepieces.com
Website: https://www.steelforgepieces.com/

## FAQ

**What is Z7CND17-11-02 equivalent to?**
X5CrNiMo17-12-2 (1.4401) in Europe, AISI 316 / UNS S31600 in the United States, SUS316 in
Japan, 316S31 in the United Kingdom, 0Cr17Ni12Mo2 in China, SS 2347 in Sweden, CSN 17346 in
Czechia, 08KH16N11M3 in Russia.

**What does the designation mean?**
A highly alloyed steel of about 0.07 % carbon with nominally 17 % Cr, 11 % Ni and 2 % Mo.

**What is the chemical composition?**
C max 0.08 %, Mn max 2.0 %, Si max 0.75 %, P max 0.045 %, S max 0.03 %, Cr 16.0-18.0 %,
Mo 2.0-3.0 %, Ni 10.0-14.0 %, N max 0.10 %, balance iron.

**What are the mechanical properties?**
Minimum 515 MPa tensile, 205 MPa yield at 0.2 % proof, 40 % elongation in 50 mm, 95 HRB and
217 HB maximum, solution annealed.

**Can it be forged?**
Yes. Hot worked from about 1150-1260 C, finished above about 900-925 C, then solution
annealed and rapidly cooled.

**What heat treatment applies?**
Solution annealing only, about 1010-1125 C with rapid cooling. The grade cannot be hardened
by thermal treatment.

**How corrosion resistant is it?**
PREN of type 316 is about 24. Subject to chloride stress corrosion cracking above about 60 C.
Chloride tolerance in potable water falls from about 1000 mg/L at ambient to about 500 mg/L
at 60 C.

**Is it magnetic?**
Fully austenitic with very low magnetic permeability in the annealed state. Cold work can
induce some ferromagnetic response.

**Difference between Z7CND17-11-02, Z7CND17-12-02 and Z6CND17-11?**
All three cross-reference to X5CrNiMo17-12-2 (1.4401) and differ in the nominal carbon and
nickel figures carried in the name.

**What certification is supplied?**
EN 10204 3.1 mill test certificate as standard, 3.2 with third-party witness on request.
Ultrasonic testing to EN 10228-3, SEP 1921 or ASTM A388.

**Minimum order quantity?**
Single pieces accepted. Price breaks at three, ten and twenty-five pieces.
