# X12CrNi17-7 (EN 1.4310 / AISI 301) Open-Die Forgings

Forged rings, rolled rings, flanges, shafts, discs, sleeves and bars in X12CrNi17-7, made to drawing by Jiangyin Jiangnan Metal Co., Ltd., Jiangyin, Jiangsu, China.

Source page: https://www.steelforgepieces.com/Stainless-Steel/X12CrNi17-7.html
Manufacturer: Jiangyin Jiangnan Metal Co., Ltd.
Address: No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province 214423, China
Phone: +86-189-2135-9659
Email: sales@steelforgepieces.com
Pricing: quoted per drawing on enquiry
Last updated: 9 October 2026

## At a glance

| Item | Value |
| --- | --- |
| Designation | X12CrNi17-7, superseded DIN name for EN material number 1.4310 |
| Current EN name | X10CrNi18-8 |
| Type | Metastable austenitic chromium-nickel stainless steel |
| Equivalents | AISI 301, UNS S30100, JIS SUS301, BS 301S21, AFNOR Z11CN18-08, SS 2331 |
| Density | 7.9 g/cm3 |
| Annealed strength | Rm 500 to 750 MPa, Rp0.2 195 to 250 MPa, A min. 40 % |
| Forging temperature | approx. 1150 to 1200 C, finish above approx. 930 C |
| Solution annealing | 1000 to 1100 C followed by rapid cooling |

## Grade description

X12CrNi17-7 is the older DIN designation for the stainless steel registered under EN material number 1.4310. In the current edition of EN 10088 the grade is named X10CrNi18-8, and mill data sheets for 1.4310 still list X12CrNi17-7 as the previous designation. It is a metastable austenitic Cr-Ni steel, known internationally as AISI 301 and UNS S30100. The main feature of the grade is its high rate of work hardening: deformation transforms part of the austenite into martensite, so strength rises steeply with cold work while the annealed material stays soft and formable.

Jiangyin Jiangnan Metal Co., Ltd. forges this grade on open-die presses and ring-rolling equipment. Parts are normally supplied solution annealed, with machining allowance or finish machined to the customer drawing.

Note on molybdenum: a number of online listings describe X12CrNi17-7 as a vacuum-remelted austenitic stainless steel alloyed with molybdenum. That description does not match this grade. Molybdenum is not an alloying addition in 1.4310. EN 10088-2 limits it to 0.80 % maximum as a residual element. Where a molybdenum-bearing austenitic steel is required for chloride pitting resistance, specify 1.4401 (316) or 1.4404 (316L).

## Chemical composition

Composition limits in mass %, to EN 10088-2 for X10CrNi18-8 (1.4310).

| C | Si | Mn | P | S | Cr | Ni | Mo | N |
| --- | --- | --- | --- | --- | --- | --- | --- | --- |
| 0.05 to 0.15 | max 2.00 | max 2.00 | max 0.045 | max 0.015 | 16.0 to 19.0 | 6.0 to 9.5 | max 0.80 | max 0.11 |

The nickel range of 6.0 to 9.5 % is deliberately lean. That is what makes the austenite metastable and gives the grade its work-hardening behaviour. The same leanness affects hot ductility, which is why heating and finishing temperatures are controlled closely during forging.

## Mechanical properties

Room-temperature properties for X10CrNi18-8 (1.4310). Annealed values are quoted for nominal diameters 2 to 25 mm. Properties of heavy forged sections are agreed at enquiry and verified on the actual piece.

| Property | Condition | Value |
| --- | --- | --- |
| Tensile strength Rm | Soft annealed (+A) | 500 to 750 MPa |
| Tensile strength Rm | Solution annealed and cold drawn (+AT+C) | 850 to 890 MPa |
| 0.2 % proof strength Rp0.2 | Soft annealed (+A) | 195 to 250 MPa |
| Elongation at fracture A | Soft annealed (+A) | min. 40 % |
| Reduction of area Z | Soft annealed (+A) | 60 to 65 % |
| Brinell hardness | Soft annealed (+A) | max 230 HB |
| Density | Not applicable | 7.9 g/cm3 |
| Intergranular corrosion resistance | Delivery and sensitised condition | Not resistant |

With carbon permitted up to 0.15 %, 1.4310 sensitises readily and is classified as not resistant to intergranular corrosion in the as-delivered condition or after sensitisation. For welded assemblies in aggressive media, a low-carbon or stabilised grade such as 1.4541 (321) or 1.4550 (347) is the safer selection.

## Equivalent grades

| Standard or region | Designation |
| --- | --- |
| EN 10088, current name | X10CrNi18-8 |
| EN material number | 1.4310 |
| DIN Werkstoff, former name | X12CrNi17-7 |
| USA, AISI and UNS | 301, S30100 |
| Japan, JIS | SUS301 |
| France, AFNOR | Z11CN18-08, Z12CN18-09 |
| United Kingdom, BS | 301S21, 302S26 |
| Sweden, SS | 2331 |
| ISO | X9CrNi18-8 |

Equivalences are close but not always identical. Confirm against the specification governing the order.

## Forging and heat treatment

Published hot-working practice for 1.4310 puts the forging heat at roughly 1150 to 1200 C, with the stock heated through slowly and evenly rather than charged cold into a hot furnace. Deformation should stop before the section drops below about 930 C. One data sheet for the same material number gives the forging range as 1150 to 1250 C, states that the steel must not be forged below 930 C, and requires solution annealing after forging.

Optimum properties are obtained by solution annealing between 1000 and 1100 C followed by rapid cooling. Rapid cooling keeps chromium carbides in solution. Dwelling between roughly 420 and 800 C is avoided during both heating and cooling.

## Forged product forms

| Product form | Typical items |
| --- | --- |
| Forged rings and rolled rings | Seamless rolled rings, retaining rings, spacer rings, bearing races, ring blanks |
| Forged flanges | Weld-neck, blind, slip-on, long weld-neck, special profile flanges |
| Forged shafts | Straight shafts, stepped shafts, spindles, eccentric shafts, crankshafts |
| Forged discs and disks | Solid discs, bored discs, gear and coupling blanks |
| Forged sleeves and bushings | Hollow forgings, liners, bushings, cylinder sleeves |
| Forged tubes and tube sheets | Bored hollow forgings, heat-exchanger tube sheets |
| Forged bars and blocks | Round, square and rectangular bar, step-forged blocks |
| Forged valve components | Valve bodies, bonnets, stems, seat rings, valve blocks |
| Forged gear blanks | Gear blanks, pinion blanks, coupling hubs |
| Forged nozzles and manifolds | Nozzles, hubs, manifold bodies, forging rolls |

## Applications

The grade is selected where a tough, formable austenitic stainless steel with good general corrosion resistance and high strength after working is wanted, and where the service environment does not demand a molybdenum-bearing or stabilised grade. Common component groups include chemical and food-processing equipment, pressure vessel and heat-exchanger internals, columns, towers, tanks and silos, general mechanical and power-transmission parts, and valve and pump components. Welded parts in corrosive duty should be checked against alternative grades before the order is placed.

## Testing, inspection and certification

Ultrasonic examination to EN 10228-3, SEP 1921 or ASTM A388 as agreed, with chemical analysis, mechanical testing and dimensional inspection. Material certificates to EN 10204 3.1, or EN 10204 3.2 with third-party endorsement. State the acceptance class and inspection body at enquiry stage, since both affect lead time and price.

## FAQ

**Is X12CrNi17-7 the same material as 1.4310?**
Yes. X12CrNi17-7 is the superseded designation for material number 1.4310. The current EN 10088 steel name for the same material number is X10CrNi18-8. Orders are accepted under either name.

**Does X12CrNi17-7 contain molybdenum?**
Not as an alloying addition. EN 10088-2 permits a maximum of 0.80 % Mo as a residual element.

**What is the forging temperature for X12CrNi17-7?**
Approximately 1150 to 1200 C, with forging stopped before the section cools below about 930 C, followed by solution annealing at 1000 to 1100 C and rapid cooling.

**Can X12CrNi17-7 be welded?**
It can be welded, but carbon up to 0.15 % makes it prone to sensitisation, and the grade is not classified as resistant to intergranular corrosion in the delivery or sensitised condition. For welded parts in corrosive service a low-carbon or stabilised austenitic grade is usually preferred.

**What sizes and weights can you forge?**
Capacity depends on the product form. Send the drawing, or the rough dimensions and finished weight, for confirmation against press and ring-rolling capacity.

**How are X12CrNi17-7 forgings priced?**
Open-die forgings are quoted individually against the drawing. Price depends on finished weight, machining state, heat treatment, non-destructive testing and certification level, so no list price applies.

**Who supplies X12CrNi17-7 forgings?**
Jiangyin Jiangnan Metal Co., Ltd., an open-die forging factory at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province 214423, China. Contact sales@steelforgepieces.com or +86-189-2135-9659.

## Request a quotation

Send the drawing, or the grade, dimensions, quantity and certification required. Include product form, heat-treatment condition, NDT requirement and certificate type (EN 10204 3.1 or 3.2).

Jiangyin Jiangnan Metal Co., Ltd.
No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province 214423, China
Phone and WhatsApp: +86-189-2135-9659
Email: sales@steelforgepieces.com

## Related grades

17-7PH, 17-4PH, 15-5PH, PH13-8Mo, A182-F321, A182-F347, A182-F51, A182-F53, A182-F55, 904L, Sanicro 28, Nitronic 60.

## Technical sources

1. EN 10088-1, 10088-2 and 10088-3 data for X10CrNi18-8 (1.4310), European Steel and Alloy Grades database (steelnumber.com).
2. thyssenkrupp Materials (UK) data sheet for stainless steel 1.4310 / 301, recording X10CrNi18-8 as the material code and X12CrNi17-7 as the previous designation.
3. Swiss Steel Group data sheet for 1.4310, solution annealing range and sensitisation behaviour.
4. Zapp Ergste 1.4310 data sheet, forging temperature range and minimum finishing temperature.

Values are given for guidance. The governing document for any order is the purchase specification agreed in writing.
