# UNS S31050 Forgings: EN 1.4466 / X1CrNiMoN25-22-2 / 310MoLN

**Supplier:** Jiangyin Jiangnan Metal Co., Ltd., open-die forging factory
**Address:** No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
**Phone:** +86-189-2135-9659
**Email:** sales@steelforgepieces.com
**Page:** https://www.steelforgepieces.com/Stainless-Steel/UNS-S31050.html
**Updated:** 5 October 2026

## Summary

UNS S31050 is a fully austenitic chromium-nickel-molybdenum stainless steel with low carbon (0.030 % max) and controlled nitrogen (0.10 to 0.16 %), nominally 25 % Cr, 22 % Ni and 2 % Mo. It is designated EN 1.4466 / X1CrNiMoN25-22-2 and is commonly called 310MoLN. It was developed for urea and nitric acid service. For forgings the governing specification is ASTM A182 grade F310MoLN.

UNS S31050 is not a duplex stainless steel. Nickel at 21 to 23 % together with the nitrogen addition stabilises the austenite phase.

## Forged shapes available

Seamless rolled rings and forged rings; flanges, blinds, tube sheets and nozzles; round bars, hollow bars and forged tube or pipe blanks; discs, disks and blocks; shafts, eccentric shafts, spindles, gear blanks and rolls; sleeves, bushings and wear rings; valve bodies, bonnets, stems and seat rings; custom open-die shapes to drawing.

## Chemical composition

ASTM A182 / A182M grade F310MoLN (UNS S31050), weight %:

| Element | Limit |
|---|---|
| C | 0.030 max |
| Mn | 2.00 max |
| P | 0.030 max |
| S | 0.015 max |
| Si | 0.40 max |
| Cr | 24.0-26.0 |
| Ni | 21.0-23.0 |
| Mo | 2.00-3.00 |
| N | 0.10-0.16 |
| Fe | Balance |

EN 1.4466 limits are close but tighten S to 0.010 max and Mo to 2.00-2.50. Nominal mill analysis for the equivalent Alleima 2RE69: C 0.020 max, Si 0.4 max, Mn 1.7, P 0.015 max, S 0.010 max, Cr 25, Ni 22, Mo 2.1, N 0.12.

The 0.10 to 0.16 % nitrogen addition stabilises and strengthens the austenite phase. A UNS S31050 datasheet that omits nitrogen, or that shows single digit nickel, is describing a different material.

## Mechanical properties

Minimum room temperature values for forgings, ASTM A182 F310MoLN:

| Property | Metric | Imperial |
|---|---|---|
| Tensile strength, min | 540 MPa | 78 ksi |
| Yield strength 0.2 %, min | 255 MPa | 37 ksi |
| Elongation in 2 in. or 4D, min | 25 % | 25 % |
| Reduction of area, min | 40 % | 40 % |

EN 1.4466 bar and plate is generally quoted at Rp0.2 250 MPa min with Rm 540-740 MPa. Alleima quotes Rp0.2 270 MPa min and Rm 580-780 MPa for 2RE69 tube and pipe, and notes that lower values can apply to bar, plate, sheet and forgings.

## Physical properties at 20 C

| Property | Value |
|---|---|
| Density | 7.9 g/cm3 (0.29 lb/in3) |
| Modulus of elasticity | 195 GPa |
| Thermal conductivity | 13-14 W/m C |
| Specific heat capacity | 485-500 J/kg C |
| Mean thermal expansion 30-100 C | 15.5 x 10-6 /C |
| Relative magnetic permeability | about 1.003 |
| Hardness | 95 HRB max (Alleima 2RE69) |

## Equivalent grades

| System | Designation |
|---|---|
| UNS | S31050 |
| EN material number | 1.4466 |
| EN name | X1CrNiMoN25-22-2 |
| Common name | 310MoLN |
| ASTM A182 grade symbol | F310MoLN |
| AFNOR | Z1 CND 25.22 AZ |
| DIN (obsolete) | X2 CrNiMo 25 22 2 |
| Proprietary | Alleima 2RE69 (formerly Sandvik), Industeel UREA 310Mo LN, also sold as 725LN |
| Related higher alloy grade | EN 1.4465 / X1CrNiMoN25-25-2 |

Not the same as UNS S31002 (310L, 2RE10), which has no molybdenum addition.

## Heat treatment

Supplied solution annealed. Published practice:

- Alleima 2RE69: 1070-1120 C (1960-2050 F), 5-15 minutes depending on size, then rapid cooling in water or air.
- Industeel UREA 310Mo LN plate: final full annealing at 1140-1180 C (2084-2156 F) followed by water quenching.

Hot working of 2RE69 is carried out between 1100 and 850 C. On forged sections the final cycle is set against the customer or urea licensor specification, and the furnace chart is recorded on the certificate.

## Corrosion resistance

Data published for the equivalent Alleima 2RE69:

- Urea and carbamate corrosion: excellent resistance at high pressure and temperature.
- Nitric acid: iso-corrosion performance in aerated nitric acid better than ASTM 304L.
- Intergranular corrosion: highly resistant after welding. Huey values on TIG welded unsensitised specimens typically below 0.12 mm per year, selective attack usually under 10 micron.
- Pitting and crevice corrosion: critical pitting temperature in neutral chloride solution higher than ASTM 316L, crevice resistance considerably better than 316L.
- Chloride stress corrosion cracking: slightly more resistant than 304 and 316 types in laboratory tests.
- Erosion corrosion: good, which is why the grade is used for urea stripper ferrules.

Forged material should be qualified against the actual service conditions and licensor requirements.

## Applications

High pressure urea plant equipment: stripper tubes and ferrules, carbamate condensers, decomposers, reactor coils. Alleima lists 2RE69 against urea specifications from Stamicarbon, Saipem, Kellogg and Urea Casale, with ASME Boiler and Pressure Vessel Code Section VIII Divisions 1 and 2 approval and ASME Code Case 2038-5 for forgings.

Also used in nitric acid coolers and condensers cooled with polluted cooling water, heating coils and pipe in NPK plants, separator and heat exchanger parts, pulp and paper, chemical and pharmaceutical production, waste treatment thermal oxidisers, seawater desalination, valve components and compressor or pump parts.

## Welding

TIG or GTAW preferred, no preheat, heat input below about 1.0 kJ/mm, interpass temperature below 100 C, string bead technique. Filler ISO 14343 S 25 22 2 N L for TIG and MIG, ISO 3581 E 25 22 2 N L B for MMA. ISO 14343 S 25 22 2 N L wire or strip for overlay welding of tube sheets and high pressure vessels. Metalcor lists filler 1.4455 for 1.4466.

## Manufacturing and quality scope

| Item | Scope |
|---|---|
| Melting | EAF + VOD, ESR remelt on request |
| Forming | Open-die forging, ring rolling, upsetting, drawing out |
| Heat treatment | Solution annealing with water or air quench, furnace charts recorded |
| Ultrasonic testing | EN 10228-3, SEP 1921, ASTM A388 |
| Other NDT | Liquid penetrant, dimensional inspection, PMI on request |
| Mechanical testing | Tensile, impact, hardness |
| Corrosion testing | Intergranular corrosion and Huey type testing on request |
| Certification | EN 10204 3.1, or 3.2 with third party witness |
| Machining | Rough or finish machining to drawing |

## Frequently asked questions

**Is UNS S31050 a duplex stainless steel?**
No, it is fully austenitic. Nickel at 21 to 23 % plus 0.10 to 0.16 % nitrogen stabilises the austenite. It is often confused with duplex grades such as A182 F51 (S31803) and A182 F53 (S32750), which hold far less nickel and have a two phase austenitic-ferritic structure.

**What is the difference between S31050 (310MoLN) and S31002 (310L, 2RE10)?**
Both are low carbon 25 Cr austenitic grades. S31050 adds 2 to 3 % molybdenum and 0.10 to 0.16 % nitrogen, which suits it to urea carbamate service. S31002 has no molybdenum addition and is aimed mainly at nitric acid.

**Which specification should forgings be ordered to?**
ASTM A182 / A182M grade F310MoLN covers pipe flanges, forged fittings, valves and pressure parts. European equivalents sit under EN 10088-3, EN 10028-7 and EN 10216-5. Alleima also cites SEW 400 and ASME Code Case 2038-5 for forgings.

**What is the maximum size you can forge?**
It depends on the geometry and the ingot available in this grade. Send the drawing with finished dimensions for confirmation of forged weight, achievable envelope and lead time.

**Can you supply certificates and third party inspection?**
Yes. EN 10204 3.1 as standard, and EN 10204 3.2 with a third party inspector such as a classification society or a nominated agency.

**Is S31050 magnetic?**
Effectively non magnetic in the solution annealed condition. Relative magnetic permeability is about 1.003 for the equivalent 2RE69.

## How to order

Send the drawing, or OD, ID, length and thickness, with quantity, governing specification, heat treatment condition, NDT level and certificate type to sales@steelforgepieces.com, or call +86-189-2135-9659.

## Data sources

ASTM A182 / A182M grade F310MoLN composition and mechanical requirements. Alleima 2RE69 (UNS S31050) material datasheet. Metalcor 1.4466 / 310MoLN datasheet. AZoM 310 MoLN datasheet. Industeel UREA 310Mo LN datasheet. EN 10088 and EN 10216-5 designations. Manufacturing and testing scope is that of Jiangyin Jiangnan Metal Co., Ltd.
