# UNS S30100 / Type 301 Stainless Steel

**UNS S30100, designated Type 301 in the AISI and ASTM systems, is an austenitic chromium-nickel stainless steel with a nominal 17 percent chromium and 7 percent nickel and a carbon ceiling of 0.15 percent. It contains no molybdenum.**

The nickel content is lean by design, leaving the austenite metastable and giving the grade a very high work-hardening rate. Cold rolling raises tensile strength from a 515 MPa annealed minimum to a 1276 MPa minimum at full hard, so the grade is sold by temper rather than as a single property set.

Because that strength comes from rolling rather than from alloying or heat treatment, S30100 is standardised as a flat-rolled product in ASTM A240 and ASTM A666 and is not a listed grade in the stainless forging specifications.

Supplier of forgings in this grade: **Jiangyin Jiangnan Metal Co., Ltd.**, No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China. Telephone, WhatsApp and WeChat +86 189 2135 9659. Email sales@steelforgepieces.com. HTML version: https://www.steelforgepieces.com/Stainless-Steel/UNS-S30100.html

## Grade summary

| Field | Value |
|---|---|
| UNS number | S30100 |
| AISI and ASTM type | 301 |
| Structure | Austenitic, effectively non-magnetic when annealed, magnetic after cold work |
| Nominal composition | 17 Cr, 7 Ni, 0.15 C max |
| Molybdenum | None |
| Annealed minimum | 515 MPa tensile, 205 MPa yield, 40 percent elongation |
| Full hard minimum | 1276 MPa tensile, 965 MPa yield |
| Forging temperature | 1093 to 1204 C start, finish about 927 C |
| Solution anneal | 1010 to 1121 C, cool rapidly |
| Specified in | ASTM A240, ASTM A666 |
| Equivalents | EN 1.4310 X10CrNi18-8, JIS SUS 301, GB 12Cr17Ni7, BS 301S21, SS 2331 |

## 1. Specification status before ordering

| Specification | Scope | S30100 listed |
|---|---|---|
| ASTM A666/A666M | Annealed or cold-worked austenitic stainless steel sheet, strip, plate and flat bar | Yes, this is the grade the standard is best known for |
| ASTM A240/A240M | Chromium and chromium-nickel plate, sheet and strip for pressure vessels and general applications | Yes |
| ASTM A473 | Stainless steel forgings, general and low or high temperature service | No. The austenitic list runs S20100, S20200, S20500, S21900, S21904, S28200, S30200, S30215, S30300, S30400 upward. S30100 is absent |
| ASTM A182/A182M | Forged or rolled flanges, fittings, valves and parts for high temperature service | No. The austenitic family is F304, F304L, F316, F316L, F317, F317L, F321, F347 type grades |

Sources: ASTM A473-19 Table 1. ASTM A666/A666M title and scope. ATI 301 technical data sheet, which gives composition as represented by ASTM A240 and A666.

Three routes exist when a drawing calls for a 301 forging. Forge to S30100 chemistry with mechanical acceptance agreed in the purchase order rather than quoted from a forging standard. Substitute Type 304 or 304L, a listed grade in both A473 and A182, trading work-hardening rate for ductility and weldability. Substitute Type 316 or 316L where corrosion resistance governs.

## 2. Chemical composition

Weight percent, maximum unless a range is shown.

| Element | Limit | Note |
|---|---|---|
| Carbon | 0.15 max | High for an austenitic grade, drives sensitisation risk on welding |
| Chromium | 16.00 to 18.00 | Nominal 17 |
| Nickel | 6.00 to 8.00 | Nominal 7, lean by design |
| Manganese | 2.00 max | Not restricted further |
| Silicon | 0.75 max | ATI and A240 give 0.75 max, some grade tables show 1.00 max |
| Phosphorus | 0.045 max | Not restricted further |
| Sulfur | 0.030 max | Not restricted further |
| Nitrogen | 0.10 max | Higher nitrogen is the basis of 301LN |
| Molybdenum | Not specified | Not an alloying addition in this grade |
| Iron | Balance | Not restricted further |

Sources: ATI 301 technical data sheet. AZoM grade 301 composition table.

Variants: 301L cuts carbon to 0.03 percent max with nitrogen to 0.20 percent max and is covered by JIS G4305. 301LN is EN 10088-2 grade 1.4318, with 0.10 to 0.20 percent nitrogen and 16.5 to 18.5 percent chromium, and work-hardens faster than standard 301. Only plain 301 is specified in ASTM A666.

## 3. Minimum room-temperature mechanical properties

Per ASTM A240 and A666.

| Temper | Tensile min | Yield 0.2 percent min | Elongation in 50 mm min |
|---|---|---|---|
| Annealed | 515 MPa / 75 ksi | 205 MPa / 30 ksi | 40 percent |
| 1/16 hard | 620 MPa | 310 MPa | 40 percent |
| 1/8 hard | 690 MPa | 380 MPa | 40 percent |
| 1/4 hard | 862 MPa / 125 ksi | 517 MPa / 75 ksi | 25 percent |
| 1/2 hard | 1034 MPa / 150 ksi | 758 MPa / 110 ksi | 18 percent |
| 3/4 hard | 1207 MPa / 175 ksi | 931 MPa / 135 ksi | 12 percent |
| Full hard | 1276 MPa / 185 ksi | 965 MPa / 140 ksi | 9 percent |

Sources: ATI 301 technical data sheet, minimum room-temperature properties per ASTM A240 and A666. AZoM grade 301 temper table. Hardness varies with temper and is reported on the test certificate.

Some tables list annealed 301 as 758 MPa tensile, 276 MPa yield and 60 percent elongation. Those are typical values, not specification minimums. ATI gives typical annealed figures of about 724 MPa, 276 MPa and 55 to 60 percent. Use 515, 205 and 40 percent for acceptance and design.

Low temperature and fatigue: annealed material holds Charpy V-notch energy of roughly 150 J, 110 ft-lb, from plus 23 C to minus 196 C with no ductile to brittle transition. Typical tensile strength rises from about 724 MPa at room temperature to about 1896 MPa at minus 196 C with elongation near 30 percent. Endurance limit is 30 to 45 percent of tensile strength, about 241 MPa annealed and about 552 MPa at full hard.

## 4. Physical properties, annealed

| Property | Value |
|---|---|
| Density | 7.88 to 8.03 g/cm3 |
| Modulus of elasticity in tension | 193 GPa, 28 million psi |
| Melting range | 1399 to 1421 C |
| Mean thermal expansion 20 to 100 C | 16.6 to 16.9 micrometre/m/C |
| Mean thermal expansion 20 to 500 C | 18.2 to 18.6 micrometre/m/C |
| Thermal conductivity at 100 C | 16.2 to 16.3 W/m.K |
| Thermal conductivity at 500 C | 21.4 W/m.K |
| Specific heat 0 to 100 C | 500 J/kg.K |
| Electrical resistivity at 20 C | 695 to 720 nanoohm.m |
| Magnetic permeability, annealed | 1.02 max at 200 H |

Sources: ATI 301 technical data sheet. AZoM grade 301 physical property table.

## 5. Forging and heat treatment

- Forging: start 1093 to 1204 C (2000 to 2200 F), finish about 927 C (1700 F).
- Solution anneal: 1010 to 1121 C (1850 to 2050 F), cool rapidly through the carbide precipitation range. Water quench heavy sections, air cool thin sections.
- Stress relief after cold work: 371 to 538 C (700 to 1000 F), five minutes to five hours.
- The grade cannot be hardened by heat treatment. Strength comes from cold work.

Strain-hardened austenite partly transforms to martensite, so a part that is non-magnetic as forged and annealed can become magnetic after cold sizing or roll forming. Time in the 427 to 816 C band precipitates grain-boundary carbides, which underlies both sensitisation and the welding limits below. Rapid work hardening makes machining and cold forming more demanding than on Type 304.

## 6. Corrosion, oxidation and welding

AZoM rates corrosion resistance on a par with Type 304 and good in mildly corrosive conditions at ambient temperature. ATI states that corrosion properties are not as good as the 18-8 chromium-nickel steels and that susceptibility to carbide precipitation during welding restricts use in favour of 304 or 304L. Carbon reconciles the two views: at up to 0.15 percent carbon the grade is far more sensitisation-prone than 304L, so the gap widens once a part is welded or held in the sensitising range.

| Condition | Guidance |
|---|---|
| Oxidation | Good to about 840 C. Weight gain reaches 10 mg/cm2 in 1000 h at 871 C, so not suggested at or above 871 C |
| Elevated temperature design | Short-time tensile data supports design to roughly 370 to 425 C. Above that, design on creep and stress-rupture data. No significant creep advantage over other 18-8 grades |
| Welding | All standard methods. Recommended filler 308L. Anneal plain 301 weldments for maximum corrosion resistance. 301L and 301LN need no post-weld anneal |
| Spot welding | Common for assembling cold-rolled 301 parts, with no material loss of component strength |

Sources: ATI 301 technical data sheet. AZoM grade 301.

## 7. Verified applications

Railway and subway car structural components, airframe sections, highway trailer components, truck and trailer bodies, automotive mouldings and trim, wheel covers, wiper blade clips and holders, springs, hose clamps, stove element clips, curtain walls, screen frames, roof drainage systems, conveyor belts and kitchen equipment. Supplied as cold rolled strip, sheet and plate.

Sources: ATI 301 technical data sheet. AZoM grade 301. Atlas Steels 301, 301L and 301LN data sheet.

Type 301 is sometimes listed against pressure vessels, shell and tube exchangers, subsea and deepwater production systems, fluid catalytic cracking units, polythionic acid service, wellheads and Christmas trees. Those duties belong to other grades, typically 321 and 347H, F316L, or duplex and super duplex such as F51, F53 and F55, and are not supported for S30100.

## 8. Forging capability

Jiangyin Jiangnan Metal melts its own steel. Carbon, alloy, stainless and duplex grades run through the electric arc furnace, ladle furnace and vacuum oxygen decarburisation, then through the presses, the ring mill, 14 heat-treatment furnaces and the machine shop without leaving the site, so certification traces a part back to its melt number.

| Form | Envelope | Set by |
|---|---|---|
| Seamless rolled rings | OD 50 to 6,000 mm | 6 m radial-axial ring mill, upset and punch route below ring-mill range |
| Forged rings and sleeves | Sections outside the ring-mill envelope | 6,300 t, 4,000 t and 2,000 t open-die presses |
| Discs, tube sheets, blocks | Up to 5,000 mm machined diameter | 5,000 mm vertical turning lathe |
| Shafts and spindles | Up to 14,000 mm turned length | C61160 horizontal lathe, 15 m well furnace |
| Bored cylinders, hollow shafts | Up to 1,600 mm dia by 10,000 mm | CNC deep-hole drilling machine |
| Single-piece weight | Up to 30,000 kg | 60 t maximum heat, 6,300 t press |

Ultrasonic examination to EN 10228-3, SEP 1921 or ASTM A388. Certification to EN 10204 3.1, or 3.2 witnessed by BV, DNV, LR, SGS, TUV or the customer's inspector. Works approvals CCS, BV, DNV, LR and NK. Minimum order 10 kg with no minimum piece count. Lead time 20 to 60 days. Price is quoted against drawing, weight and quantity.

## 9. Questions

**Does UNS S30100 contain molybdenum?**
No. It is a plain chromium-nickel austenitic stainless steel, nominally 17 Cr and 7 Ni. ASTM A240 and A666 carry no molybdenum addition for this grade.

**Is UNS S30100 an ASTM A182 grade?**
No. The A182 austenitic family covers F304, F304L, F316, F316L, F317, F317L, F321 and F347 type grades. S30100 is specified in ASTM A240 and A666, and is also absent from the chemical requirements table of ASTM A473.

**What are the annealed minimum properties?**
515 MPa tensile, 205 MPa yield at 0.2 percent offset, 40 percent elongation in 50 mm.

**What is the forging temperature range?**
Start 1093 to 1204 C, finish about 927 C, then solution anneal at 1010 to 1121 C with rapid cooling.

**Is Type 301 magnetic?**
Annealed material is effectively non-magnetic at 1.02 maximum permeability at 200 H. Cold work raises permeability as martensite forms.

**Can Type 301 be used for sustained high-temperature service?**
Only within limits. Short-time tensile data supports design to roughly 370 to 425 C. Oxidation resistance is good to about 840 C and the grade is not suggested at or above 871 C.

**Which grade replaces 301 for forgings?**
Type 304 or 304L in most cases, Type 316 or 316L where corrosion resistance governs.

**Who forges UNS S30100 to drawing?**
Jiangyin Jiangnan Metal Co., Ltd., No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China. Telephone +86 189 2135 9659, email sales@steelforgepieces.com.

---

Reviewed 5 October 2026 by technical sales, Jiangyin Jiangnan Metal Co., Ltd. Compiled from the ATI 301 technical data sheet for UNS S30100, the AZoM grade 301 data sheet, the Atlas Steels 301, 301L and 301LN data sheet, ASTM A473-19 and the published titles and scopes of ASTM A666/A666M and A240/A240M. Figures are for guidance, are not design allowables, and do not replace the governing specification edition.
