# UNS S17400 Forgings (Type 630)

**UNS S17400 is a chromium-nickel-copper precipitation hardening martensitic stainless steel, designated Type 630.** It is hardened by a single low-temperature treatment between 900 and 1150 F (482 to 621 C), which both precipitation strengthens and tempers the martensite, reaching 200 ksi (1380 MPa) tensile strength at 44 HRC in the H900 condition. Strength and hardness are held to 600 F (316 C), oxidation resistance extends to about 1100 F (593 C), and creep-rupture strength is useful to 900 F (482 C). Unlike conventional martensitic stainless steels such as Type 410, S17400 is readily weldable.

Jiangyin Jiangnan Metal Co., Ltd. forges this grade to drawing as seamless rolled rings, flanges, shafts, discs, sleeves, bushings and tube sheets, in Condition A or any aged condition from H900 to H1150-M, including the double-aged 33 HRC condition accepted by NACE MR0175 and ISO 15156-3 for sour service.

Source page: https://www.steelforgepieces.com/Stainless-Steel/UNS-S17400.html

## Grade record

| Field | Detail |
|---|---|
| UNS number | S17400 |
| ASTM / AISI type | 630 |
| Forging specification | ASTM A705 / ASME SA-705, Grade 630 |
| Bar, wire, shapes | ASTM A564 / ASME SA-564, Type 630 |
| Sheet, plate, strip | ASTM A693 / ASME SA-693, Type 630 |
| Aerospace | AMS 5643 (bars, forgings, rings), AMS 5604 (sheet, strip, plate), AMS 5825 (welding wire) |
| Sour service | NACE MR0175, ISO 15156-3, 33 HRC maximum |
| European number | Cross-references differ: Rolled Alloys lists W. Nr. 1.4548; 1.4542 (X5CrNiCuNb16-4) is widely used in the European trade. Confirm on order. |
| Melting routes offered | EF + LF + VOD, or ESR / VAR remelt |
| Maximum single piece | 30 t |
| Maximum ring OD | 6,000 mm |
| Minimum order | 10 kg, no minimum piece count |
| Lead time | 20 to 60 days |
| Supplier | Jiangyin Jiangnan Metal Co., Ltd., No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China |
| Telephone | +86 189 2135 9659 |
| Email | sales@steelforgepieces.com |

**ASTM B564 does not apply to this grade.** B564 covers nickel and nickel alloy forgings including UNS N02200, N04400, N06600, N06603 and N06690. It appears on some S17400 listings in error. For S17400 forgings the correct reference is ASTM A705 or ASME SA-705, Grade 630.

## Chemical composition, weight percent

| Element | Minimum | Maximum |
|---|---|---|
| Chromium, Cr | 15.0 | 17.5 |
| Nickel, Ni | 3.0 | 5.0 |
| Copper, Cu | 3.0 | 5.0 |
| Niobium plus tantalum, Cb+Ta | 5 x C | 0.45 |
| Carbon, C | - | 0.07 |
| Manganese, Mn | - | 1.00 |
| Silicon, Si | - | 1.00 |
| Molybdenum, Mo | - | 0.50 |
| Phosphorus, P | - | 0.04 |
| Sulphur, S | - | 0.03 |
| Iron, Fe | balance | balance |

Chromium runs to 17.5 percent, not 17.0. Niobium and tantalum are controlled together as one value, with the minimum tied to five times the carbon content.

## Heat treatment

| Condition | Practice | Result |
|---|---|---|
| A | 1900 F +/- 25 (1040 C), 1/2 hour, air cooled or oil quenched below 90 F | Solution treated. Supply and machining condition only |
| H900 | 900 F +/- 15 (482 C), 1 hour, air cooled | Maximum hardness, low toughness, sensitive to stress-corrosion cracking |
| H925 | 925 F (496 C), 4 hours, air cooled | Very high strength |
| H1025 | 1025 F (552 C), 4 hours, air cooled | Balanced strength and toughness |
| H1075 | 1075 F (579 C), 4 hours, air cooled | Higher toughness |
| H1100 | 1100 F (593 C), 4 hours, air cooled | Higher toughness again |
| H1150 | 1150 F (621 C), 4 hours, air cooled | Overaged, 33 HRC |
| H1150D | 1150 F, 4 hours, air cool, then 1150 F, 4 hours, air cool | 31 HRC, double aged, sour service route |
| H1150-M | 1400 F +/- 25 (760 C), 2 hours, air cool, then 1150 F +/- 15, 4 hours, air cool | 27 HRC, highest toughness and machinability |

At 1900 F the structure is austenitic and transforms to low-carbon martensite on cooling; transformation is not complete until the part falls below 90 F (32 C).

**Condition A is not a service condition.** For most applications S17400 should not be used as solution treated, even where the tensile strength in that condition appears adequate. The structure is untempered martensite with low fracture toughness and ductility and poor resistance to stress-corrosion cracking.

Where H900 is specified but impact energy is marginal, ageing 4 hours instead of 1 hour develops typical properties of 196 ksi tensile, 181 ksi yield, 14 percent elongation in 2 in., 52 percent reduction of area, 43 HRC and 20 ft-lb Charpy V-notch.

## Representative longitudinal mechanical properties

Typical values for selecting a condition, not acceptance criteria.

| Property | H900 | H925 | H1025 | H1075 | H1100 | H1150 | H1150D | H1150-M |
|---|---|---|---|---|---|---|---|---|
| Tensile strength, ksi | 200 | 190 | 170 | 165 | 150 | 145 | 140 | 125 |
| Tensile strength, MPa | 1380 | 1310 | 1170 | 1140 | 1035 | 1000 | 965 | 860 |
| 0.2 % yield, ksi | 185 | 175 | 165 | 150 | 135 | 125 | 120 | 85 |
| 0.2 % yield, MPa | 1275 | 1205 | 1140 | 1035 | 930 | 860 | 825 | 585 |
| Elongation in 2 in. or 4D, % | 14 | 14 | 15 | 16 | 17 | 19 | 22 | 22 |
| Reduction of area, % | 50 | 54 | 56 | 58 | 58 | 60 | 65 | 68 |
| Hardness, Brinell | 420 | 409 | 352 | 341 | 332 | 311 | 294 | 277 |
| Hardness, HRC | 44 | 42 | 38 | 36 | 35 | 33 | 31 | 27 |
| Charpy V-notch, ft-lb | 15 | 25 | 35 | 40 | 45 | 50 | 55 | 100 |
| Charpy V-notch, J | 20 | 34 | 47 | 54 | 61 | 68 | 75 | 136 |

## Physical properties

| Property | 70 F | 212 F | 392 F | 572 F |
|---|---|---|---|---|
| Modulus of elasticity, dynamic, psi x 10^6 | 29.0 | 28.1 | 27.0 | 26.1 |
| Thermal conductivity, Btu ft / ft2 hr F | 8.6 | 9.2 | 9.8 | 10.4 |
| Coefficient of thermal expansion from 70 F, in/in F x 10^-6 | - | 7.2 | 7.5 | 7.8 |

Density 0.282 lb/in3 (7.81 g/cm3). Melting range 2560 to 2625 F (1404 to 1440 C). Poisson's ratio 0.272. Electrical resistivity 463 ohm circular mil per foot. Ferromagnetic in all conditions.

## Corrosion resistance and sour service

Corrosion resistant across chemical process service, with oxidation resistance to about 1100 F (593 C). Resistance to stress-corrosion cracking falls as strength rises, and H900 is the condition most sensitive to it, so where chloride stress-corrosion cracking is credible the part should be aged to the lowest strength that satisfies the design minima.

NACE MR0175 and ISO 15156-3 list S17400 at a maximum hardness of 33 HRC, reached by solution treatment followed by double age hardening in the H1150D or H1150-M condition. This must be stated at enquiry stage, because it fixes the ageing cycle and adds a hardness survey to the test plan.

## Machining, welding and size limits

Machinability is comparable in character to 410, 420 and 430F, but the alloy is stronger and the chips run long. At 44 HRC in H900, machining is slow with heavy tool wear, so parts are normally rough machined in Condition A or an overaged condition and finished after ageing. Parts machined in H1150-M need solution treatment before final hardening.

Weldable by conventional inert gas methods without preheat. Use matching filler to AMS 5825 with post-weld ageing where the weld must respond to heat treatment, or an austenitic filler where it need not. Torch cutting in the annealed condition risks cracking; saw or water-jet cutting is safer.

| Product | Limit | Set by |
|---|---|---|
| Seamless rolled rings | OD 50 to 6,000 mm | 6 m radial-axial ring mill, upset and punch below mill range |
| Shafts and spindles | to 14,000 mm turned length | C61160 lathe, 15,000 mm pit furnace |
| Discs, tube sheets, blocks | to 5,000 mm machined diameter | 5,000 mm vertical turning lathe |
| Bored cylinders, hollow shafts | to 1,600 mm dia x 10,000 mm | CNC deep-hole drilling machine |
| Single piece weight | to 30,000 kg | 60 t heat size, 6,300 t press |

## Applications

Gate valve components, valve stems, balls, seats and bushings. Pump shafts, gears and plungers. Chemical processing equipment. Wellhead, Christmas tree, BOP and riser components under API 6A and NACE MR0175. Seamless rolled rings, gear ring blanks, retaining rings and valve seat rings. Heavy fasteners and high-strength fittings.

## Testing and documents

Ladle analysis, tensile testing and hardness in the delivered condition, and ultrasonic examination to EN 10228-3, SEP 1921 or ASTM A388 as specified. Charpy V-notch testing, hardness surveys for MR0175, positive material identification, magnetic particle and liquid penetrant inspection, grain size, intergranular corrosion testing and dimensional reports on request. Certificates to EN 10204 3.1, or 3.2 with third-party inspection. Works approvals: CCS, BV, DNV, LR, NK.

Because the steel is melted on site, the certificate traces a finished forging back to its melt number rather than stopping at a purchased billet.

## Ordering

Call out the specification, grade or type, and condition, for example ASTM A705 Gr 630 Cond. H1025. Without the condition the order is incomplete, because the same chemistry covers 125 to 200 ksi depending on ageing. Add the sour service requirement separately where it applies.

Email sales@steelforgepieces.com or telephone +86 189 2135 9659.

---

Last reviewed 4 October 2026. Composition, heat treatment practice and representative properties compiled from published mill data for UNS S17400 and Type 630, with ASTM A705, ASTM A564, ASTM A693, AMS 5643 and NACE MR0175 / ISO 15156-3. Values are typical and given for selecting a condition; they are not acceptance criteria and do not replace the governing specification. Independent producer of UNS S17400 forgings, not affiliated with the owner of any trademark referenced in the standards cited.
