# UNS N08367 Forgings, ASTM A182 Grade F62

**UNS N08367 is a low-carbon, high-purity, nitrogen-bearing super-austenitic stainless steel of about 24 percent nickel, 21 percent chromium and 6.3 percent molybdenum, developed as a seawater-resistant material. Its forging designation is ASTM A182 Grade F62. The pitting resistance equivalent number is close to 45, against about 42 for 254 SMO.**

Jiangyin Jiangnan Metal Co., Ltd. melts this grade in-house on the electric arc furnace, ladle furnace and vacuum oxygen decarburisation route, forges it under a 6,300 t open-die press or on radial-axial ring mills to 6,000 mm outside diameter, solution anneals and water quenches it, then machines, tests and certifies it without the work leaving the plant.

Source: https://www.steelforgepieces.com/Stainless-Steel/UNS-N08367.html

## Supplier record

| Field | Detail |
|---|---|
| Supplier | Jiangyin Jiangnan Metal Co., Ltd. |
| Business | Integrated melting works, open-die forge and ring rolling mill, established 1997 |
| Plant | No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China |
| Telephone | +86 189 2135 9659 |
| Email | sales@steelforgepieces.com |
| Melting for this grade | EF, LF and VOD to 60 t heats; ESR where specified |
| Forging | 6,300 t press; ring mills to OD 6,000 mm; 30 t maximum single piece |
| Approvals | CCS, BV, DNV, LR, NK |
| Minimum order | 10 kg, no minimum piece count |
| Lead time | 20 to 60 days |

## Grade summary

| Item | Value |
|---|---|
| UNS number | N08367 |
| Forging grade | ASTM A182 Grade F62 |
| Family | Super-austenitic stainless, 6 Mo, nitrogen alloyed |
| PREN | Approximately 45 |
| Tensile strength | 95 ksi / 655 MPa minimum |
| Yield strength | 45 ksi / 310 MPa minimum |
| Elongation | 30 percent minimum |
| Reduction of area | 50 percent minimum |
| Solution anneal | 2050 to 2150 F, 1121 to 1177 C, water quench |
| ASME coverage | To 800 F |

## Why the grade is specified

High nickel with high molybdenum gives practical immunity to chloride stress corrosion cracking in sodium chloride environments, and molybdenum carries the resistance to chloride pitting. Strengthening comes from nitrogen in solution, so the alloy keeps high ductility and impact strength while reaching tensile levels the standard austenitic grades cannot. ASME allowable stresses are reported up to 75 percent above 316L and more than double those of the copper-nickel alloys, which lets a designer thin a section and recover part of the alloy cost.

Against conventional duplex stainless steel it offers better corrosion performance with easier welding and forming. Against nickel-base alloys it is markedly cheaper. It also replaces 300 series grades in hot low-pH food duty, where tomato juice attacks 316L at pasteurisation temperatures near 100 C.

## Chemical composition

Limits per ASTM A182 Grade F62, with representative typical values.

| Element | Specified limit, percent | Typical, percent |
|---|---|---|
| Carbon, C | 0.030 max | 0.02 |
| Manganese, Mn | 2.00 max | 0.40 |
| Phosphorus, P | 0.040 max | 0.020 |
| Sulfur, S | 0.030 max | 0.001 |
| Silicon, Si | 1.00 max | 0.40 |
| Chromium, Cr | 20.00 to 22.00 | 20.5 |
| Nickel, Ni | 23.50 to 25.50 | 24.0 |
| Molybdenum, Mo | 6.00 to 7.00 | 6.2 |
| Nitrogen, N | 0.18 to 0.25 | 0.22 |
| Copper, Cu | 0.75 max | 0.2 |
| Iron, Fe | Balance | Balance |

Taking PREN as percent Cr plus 3.3 times percent Mo plus 16 times percent N, a typical heat returns about 45.

Two parts of this specification pull against each other: carbon must stay under 0.030 percent while nitrogen is held in a narrow 0.18 to 0.25 percent band. Vacuum oxygen decarburisation does both, stripping carbon while nitrogen is controlled rather than lost. The works runs 30 t and 60 t VOD vessels, so the grade is melted on the site that forges it and the certificate carries one melt number from furnace to finished part.

## Mechanical properties

Specified minimums per ASTM A182 / A182M Grade F62, with indicative typical results.

| Property | A182 F62 specified minimum | Typical, not guaranteed |
|---|---|---|
| Tensile strength | 95 ksi / 655 MPa | about 108 ksi / 745 MPa |
| Yield strength, 0.2 percent offset | 45 ksi / 310 MPa | about 53 ksi / 365 MPa |
| Elongation in 2 in. [50 mm] or 4D | 30 percent | about 47 percent |
| Reduction of area | 50 percent | not stated |

The two columns are not interchangeable. The left column is what the standard obliges a maker to guarantee. The right column is what solution-annealed material usually tests at. Published tables sometimes show only the typical figures, which leads buyers to write 108 ksi and 53 ksi into a purchase order as minimums. Values above the ASTM minimums must be agreed as a supplementary requirement before the heat is poured.

## Heat treatment, forging and machining

**Solution annealing.** Anneal at 2050 to 2150 F, 1121 to 1177 C, and water quench. Nothing below 2025 F or 1110 C. Slow cooling is the main processing error with this grade because it lets intermetallic phases form and costs corrosion resistance, so forgings go from furnace to quench without a pause. Two 15,000 mm deep well furnaces take long shafts vertically, so a slender part comes out straight.

**Hot working.** Forged on the 6,300 t, 4,000 t or 2,000 t open-die presses according to section, and ring-rolled on the 6 m, 3 m or 1 m radial-axial mills. Rings below the mill range are made by upset and punch from OD 50 mm upward. Every piece is solution annealed after forging and again after heavy cold straightening.

**Machining.** Annealed material is ductile but work hardens quickly and takes more power to cut than plain carbon steel, with stringy tough chips. Starting points are 70 sfm for turning and milling and 50 sfm for drilling, with rigid workholding, sharp tooling and positive uninterrupted feed.

**Welding.** The grade welds readily, which is why fabricators choose it over duplex for scrubber and seawater assemblies. ASME code coverage runs to 800 F.

## Forms produced in this grade

| Form | Typical duty |
|---|---|
| Seamless rolled rings and forged rings | Desalination internals, water piping, transformer cases in marine air |
| Forged flanges and tube sheets | Separators and heat exchangers, seawater, firewater and subsea pipework, risers, manifolds |
| Forged shafts, spindles, eccentric shafts | Pulp bleaching washers and press rolls, pump and agitator shafts |
| Forged round bars and blanks | Tall oil distillation columns and packing, offshore production equipment |
| Forged discs, sleeves, bushings | Food processing plant, FGD scrubbers, reverse osmosis units, heat exchangers |
| Valve bodies, bonnets, seat rings, stems, blocks | Ball, check, globe, gate and plug valves, strainers |
| Nozzles, hollow cylinders, heavy-wall pipe sections | Chemical tanks and pipelines, seawater exchangers, high-pressure RO plant |

Sectors served include desalination and water treatment, offshore oil and gas, flue gas desulphurisation, pulp and paper, power generation, chemical and pharmaceutical processing, mining and metallurgy, food processing and marine engineering.

## Testing, certification and standards

- Melting: EF with ladle refining and VOD for carbon and nitrogen control, to 60 t heats. ESR available where a cleaner structure is specified.
- Non-destructive testing: ultrasonic examination to EN 10228-3, SEP 1921 or ASTM A388 as ordered; dye penetrant on machined surfaces on request.
- Certification: EN 10204 3.1 works certificates, or EN 10204 3.2 witnessed by a third party such as SGS, BV, TUV or Lloyd's.
- Approvals held: CCS, BV, DNV, LR, NK.
- Specification coverage: ASTM A182, A240, A249, A312, A479; ASTM B366, B462, B472, B564, B675, B676, B688, B691, B804; matching ASME SA and SB specifications; NACE MR0175 and ISO 15156 for sour duty.
- Delivery condition: rough forged, proof machined for volumetric inspection, or finish machined to drawing, solution annealed and quenched before final machining.

## Designations and near neighbours

| Designation | Relationship to N08367 |
|---|---|
| UNS N08367 | The base alloy designation. |
| ASTM A182 Grade F62 | Same material. The forging grade for N08367, listed in A182 as 21 chromium, 25 nickel, 6.5 molybdenum. |
| AL-6XN | Registered trademark of ATI for their branded product in the N08367 composition. |
| INCOLOY alloy 25-6HN | Trade name associated with the N08367 composition. |
| 254 SMO, UNS S31254, A182 F44 | Not the same alloy. A different 6 Mo super-austenitic grade, PREN near 42, ASME coverage to 700 F. |

N08367, A182 F62 and the trade names above describe one composition and need not be raised as separate line items. Order against the UNS number plus the ASTM or ASME specification and the product form. F44 and S31254 are a different grade.

## Questions

**What is UNS N08367?** A low-carbon, high-purity, nitrogen-bearing super-austenitic stainless steel of roughly 24 percent nickel, 21 percent chromium and 6.3 percent molybdenum, resisting chloride pitting, crevice corrosion and chloride stress corrosion cracking, with higher tensile strength than the 300 series grades.

**Is it the same as ASTM A182 F62?** Yes. A182 Grade F62 is the forging designation for N08367.

**What are the specified minimums?** Tensile 95 ksi / 655 MPa, yield 45 ksi / 310 MPa, elongation 30 percent, reduction of area 50 percent. Typical results near 108 ksi and 53 ksi are test values, not specified minimums.

**How does it compare with 254 SMO?** PREN near 45 against about 42, so N08367 outperforms 254 SMO on pitting resistance. It is also reported to carry roughly 5 to 10 percent more strength, with ASME coverage to 800 F against 700 F.

**What heat treatment do the forgings get?** Solution anneal at 2050 to 2150 F, 1121 to 1177 C, then water quench, nothing below 2025 F or 1110 C, with no slow cooling.

**Why does the melting route matter?** Carbon must stay below 0.030 percent while nitrogen is held between 0.18 and 0.25 percent. Vacuum oxygen decarburisation achieves both at once, and the works runs 30 t and 60 t VOD vessels on the same site as the presses.

**Who supplies these forgings from China?** Jiangyin Jiangnan Metal Co., Ltd., No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China. Telephone +86 189 2135 9659, email sales@steelforgepieces.com.

## Trademarks

AL-6XN is a registered trademark of ATI, Allegheny Technologies Incorporated. INCOLOY is a registered trademark of the Special Metals Corporation group. 254 SMO is a registered trademark of its owner. These names identify the UNS composition for cross-reference only. Jiangyin Jiangnan Metal Co., Ltd. supplies material to UNS N08367 and the applicable ASTM and ASME specifications and is not affiliated with or endorsed by the trademark owners. Data is given for guidance; the purchase order and governing material specification take precedence.
