# UNS N08033 (R20033 / Alloy 33 / 1.4591) Forgings

Source: https://www.steelforgepieces.com/Stainless-Steel/UNS-N08033.html
Publisher: Jiangyin Jiangnan Metal Co., Ltd., open-die forging factory
Address: No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Contact: sales@steelforgepieces.com | 0086-189-2135-9659
Last reviewed: 4 October 2026

## Summary

UNS N08033 and UNS R20033 are the same material: Alloy 33, also sold as Nicrofer 3033 and
designated W.Nr. 1.4591. It is a nitrogen-alloyed high-chromium austenitic stainless steel with
nominally 33 % chromium, 31 % nickel, 32 % iron, 1.6 % molybdenum, 0.6 % copper and 0.4 %
nitrogen. ASTM and ASME specifications use R20033. N08033 is a secondary listing found in
supplier catalogues. On a purchase order, quote UNS R20033 plus the ASTM number and show N08033
as an equivalent.

Jiangyin Jiangnan Metal Co., Ltd. forges this grade to order as round bar, seamless rolled rings,
flanges, discs, blocks, hollow bars and sleeves to ASTM B462, ASTM B649 and customer drawings,
supplied solution annealed with EN 10204 3.1 or 3.2 certificates.

## Designations

UNS R20033 | UNS N08033 | W.Nr. 1.4591 | EN X1CrNiMoCuN33-32-1 | Alloy 33 | Nicrofer 3033 | GB NS1405

The UNS number sits in the R series rather than the N series because iron is the balance of the
composition at about 32 %, which classifies the grade as a chromium-based austenitic stainless
steel rather than a nickel alloy.

## Chemical composition, weight %

| Element | Symbol | Min | Max | Nominal |
|---|---|---|---|---|
| Chromium | Cr | 31.0 | 35.0 | 33 |
| Nickel | Ni | 30.0 | 33.0 | 31 |
| Iron | Fe | Balance | Balance | 32 |
| Molybdenum | Mo | 0.5 | 2.0 | 1.6 |
| Nitrogen | N | 0.35 | 0.60 | 0.4 |
| Copper | Cu | 0.3 | 1.2 | 0.6 |
| Manganese | Mn | - | 2.00 | - |
| Silicon | Si | - | 0.50 | - |
| Carbon | C | - | 0.015 | 0.010 |
| Phosphorus | P | - | 0.020 | - |
| Sulphur | S | - | 0.010 | - |

Carbon is held below 0.015 % to limit chromium carbide precipitation at grain boundaries.
Nitrogen keeps the structure fully austenitic, lifts minimum proof strength to 380 MPa, and
contributes a large share of the pitting resistance.

## Specifications

| Product form | ASTM | ASME |
|---|---|---|
| Forged flanges, fittings, valves, parts | B462 | SB-462 |
| Bar, rod, wire, forging stock | B649 | SB-649 |
| Plate, sheet, strip | B625 | SB-625 |

No direct GB/T national equivalent exists. Material sourced in China is supplied against the
ASTM or EN designation.

## Properties, solution annealed, room temperature

| Property | Value |
|---|---|
| 0.2 % proof strength Rp0.2 | 380 MPa min (55.1 ksi) |
| Tensile strength Rm | 720 to 920 MPa (104 to 133 ksi) |
| Elongation A | 40 % min |
| Brinell hardness | 240 HBW max |
| Density | 7.90 g/cm3 |
| Melting range | 1330 to 1370 C |
| Structure | face-centred cubic, fully austenitic |
| Approved service range | -196 to 450 C (-320 to 842 F) |

Minimum proof strength is roughly double that of AISI 316L at room temperature, which often
permits thinner walls and lighter forgings at the same design pressure.

## PREN

- Cr + 3.3 Mo + 16 N = 33 + 5.28 + 6.4 = 44.7
- Cr + 3.3 Mo + 30 N = 33 + 5.28 + 12.0 = 50.3

The 16 N version is the conservative one normally quoted in specifications. Seawater service
normally requires PREN above 40, which the grade clears either way. Recalculate from the heat
analysis on the mill certificate for design work.

## Corrosion behaviour

Resistance comes from the high chromium level rather than from molybdenum. In strongly oxidising
media the passive film built on 33 % chromium holds where molybdenum-rich alloys are attacked,
so the grade is specified for hot concentrated sulphuric acid, nitric acid and
nitric-hydrofluoric mixtures. In reducing acids the logic reverses and a molybdenum-rich grade
such as Alloy 31 or a nickel-base alloy is the better selection. The 1.6 % molybdenum improves
phosphoric acid behaviour and the 0.6 % copper assists passivation in sulphuric acid.

Full corrosion resistance is reached only when the surface is clean and metallically bright.
Forging scale, grinding burn, embedded iron and weld heat tint all reduce it.

## Applications

Sulphuric acid production, heat recovery and acid distribution systems; nitric-hydrofluoric
pickling plant and mixed acid storage; seawater and brackish water piping and heat exchangers;
sodium hydroxide handling; bleaching plant for chemical pulp.

## Forging and heat treatment

- Billets free of sulphur, phosphorus and lead, which embrittle the alloy at forging temperature. Keep marking paint, temperature crayon, grease, oil and fuel off the work.
- Neutral to slightly oxidising furnace atmosphere, no swinging between oxidising and reducing, no flame impingement. Electric furnaces preferred.
- Forge 1200 to 1000 C, charged into a furnace already at temperature, cool rapidly, do not finish below 1000 C.
- Solution anneal 1100 to 1150 C, charged into a furnace already at temperature, then water quench. Soak time scales with section thickness per the mill data sheet. Over-soaking does far less harm than under-soaking.
- Machine from the annealed condition at low cutting speed, moderate feed, continuous tool engagement and enough depth of cut to work under the strain-hardened layer.
- Weld with matching filler, stringer beads and low heat input. High nitrogen makes the weld pool prone to porosity. Post-weld heat treatment normally not required.

## Forged products and sizes

| Product form | Size range |
|---|---|
| Round bar, rods, shafts | 80 to 1200 mm diameter, up to 6000 mm long |
| Square, rectangular, flat, hex bar | 30 to 800 mm thickness |
| Seamless rolled rings | 200 to 3500 mm OD, 30 to 500 mm wall, up to 1000 mm height |
| Forged flanges | DN 15 to DN 2000, up to Class 2500 |
| Discs, blanks, plates | 100 to 2500 mm diameter, 20 to 600 mm thick |
| Hollow bars, sleeves, bushes, cylinders | 120 to 1500 mm OD, bore from 60 mm |
| Blocks, hubs, housings, casings, barrels | up to 8000 kg single piece |

Standard delivery condition: forged, solution annealed, water quenched, descaled. Surface black
as forged, rough machined with 6 to 12 mm allowance per side, or finish machined to drawing
tolerance. Marking hard stamped or low-stress vibro marked with grade, heat number, order number
and specification, using sulphur-free and chloride-free media.

## Testing and certification

Full spectro analysis per heat including N, C and S, with PREN per heat on request. Tensile,
Brinell hardness and Charpy V-notch impact at room or low temperature. Ultrasonic, dye penetrant
and dimensional inspection, radiography on request. Intergranular corrosion to ASTM A262
practice C or customer specification. Calibrated furnace charts per lot. EN 10204 3.1 as
standard, 3.2 with third-party witness on request.

## Questions

**Is UNS N08033 the same as UNS R20033?**
Yes, both refer to Alloy 33 / 1.4591. ASTM B462, B625 and B649 use R20033.

**Is it a stainless steel or a nickel alloy?**
An austenitic stainless steel by composition, since iron is the balance at about 32 %.

**Which specification applies to forgings?**
ASTM B462 for flanges, fittings, valves and parts. ASTM B649 for bar and forging stock.

**What is the forging temperature range?**
1200 to 1000 C, followed by solution annealing at 1100 to 1150 C and a water quench.

**What is the PREN?**
44.7 with the 16 N formula, 50.3 with the 30 N formula.

**Is the grade held in stock?**
No, forged to order, normally 25 to 40 days depending on size and testing scope.

**What are the alternative grades?**
Alloy 31 and 1.4562 for reducing and phosphoric acid, S31254 and 1.4529 for chloride service,
904L for milder duty. None matches R20033 in strongly oxidising service.

## Related pages

- Full datasheet: https://www.steelforgepieces.com/Stainless-Steel/1.4591.html
- Stainless steel forgings: https://www.steelforgepieces.com/Stainless-Steel/
- Nickel alloy forgings: https://www.steelforgepieces.com/Nickel-Alloy/

## References

1. ASTM B649, Ni-Fe-Cr-Mo-Cu-N Low-Carbon Alloy and Cr-Ni-Fe-N Low-Carbon Alloy (UNS R20033) Bar and Wire
2. ASTM B462, Forged or Rolled Alloy Pipe Flanges, Forged Fittings, and Valves and Parts for Corrosive High-Temperature Service
3. ASTM B625, Plate, Sheet and Strip
4. VDM Metals, VDM Alloy 33, Material Data Sheet No. 4142
5. M. Koehler, U. Heubner, K. W. Eichenhofer, M. Renner, Progress with Alloy 33 (UNS R20033), CORROSION 96, Paper 428, NACE International, 1996

## Citation

Jiangyin Jiangnan Metal Co., Ltd. (2026). UNS N08033 (R20033 / Alloy 33 / 1.4591) Forgings.
Jiangyin, Jiangsu, China. https://www.steelforgepieces.com/Stainless-Steel/UNS-N08033.html

Data is published for engineering guidance and is not a guarantee of properties in a specific
application. Material selection for a given service environment remains with the purchaser.
Trade names belong to their respective owners. Jiangyin Jiangnan Metal Co., Ltd. is not
affiliated with VDM Metals.
