# SUS 890L Forgings, JIS G4303 / UNS N08904 / EN 1.4539

**Manufacturer:** Jiangyin Jiangnan Metal Co., Ltd. — open-die forging factory
**Address:** No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
**Tel:** 0086-189-2135-9659 | **Email:** sales@steelforgepieces.com
**Page:** https://www.steelforgepieces.com/Stainless-Steel/SUS-890L.html
**Updated:** 4 October 2026

## Summary

SUS 890L is the Japanese designation for the alloy sold elsewhere as 904L: a low carbon, copper bearing austenitic stainless steel of roughly 20 % Cr, 25 % Ni, 4.5 % Mo and 1.5 % Cu, carrying UNS number N08904 and EN number 1.4539. Copper gives resistance to reducing acids, sulphuric acid above all; nickel and molybdenum give resistance to chloride pitting, crevice corrosion and stress corrosion cracking. Jiangyin Jiangnan Metal Co., Ltd. forges SUS 890L to drawing as rolled rings, flanges, discs, shafts, sleeves, bushings and tube sheets, with ultrasonic testing to ASTM A388, EN 10228-3 or SEP 1921 and certificates to EN 10204 3.1 or 3.2.

## Key data

| Item | Value |
|---|---|
| JIS designation | SUS890L |
| UNS number | N08904 |
| EN number | 1.4539 |
| EN name | X1NiCrMoCu25-20-5 |
| Structure | Austenitic, non-magnetic |
| 0.2 % proof stress, min | 215 N/mm² |
| Tensile strength, min | 490 N/mm² |
| Elongation, min | 35 % |
| Hardness, max | 90 HRB / 187 HB |
| Pitting resistance equivalent | about 35 |
| Certification | EN 10204 3.1 or 3.2 |

## Chemical composition (JIS G4304 SUS890L, weight %, balance Fe)

| Limit | C | Si | Mn | P | S | Ni | Cr | Mo | Cu |
|---|---|---|---|---|---|---|---|---|---|
| Minimum | – | – | – | – | – | 23.00 | 19.00 | 4.00 | 1.00 |
| Maximum | 0.020 | 1.00 | 2.00 | 0.045 | 0.030 | 28.00 | 23.00 | 5.00 | 2.00 |

Nitrogen is named in the JIS element list but carries no numeric limit; commercial heats usually run around 0.10 %. Flat rolled 904L to ASTM B625 allows sulphur to 0.035 % rather than the 0.030 % above, so the JIS limit is the tighter of the two.

## Mechanical properties, solution treated

| Property | JIS SUS 890L | ASTM A182 F904L |
|---|---|---|
| 0.2 % proof stress, min | 215 N/mm² | 215 MPa (31 ksi) |
| Tensile strength, min | 490 N/mm² | 490 MPa (71 ksi) |
| Elongation, min | 35 % | 35 % in 2 in. |
| Hardness, max | 90 HRB / 187 HB | not specified; 220 HBW often ordered |

## Physical properties, annealed

| Property | Value |
|---|---|
| Density | 7 900 kg/m³ |
| Modulus of elasticity | 190 GPa |
| Mean thermal expansion, 0–100 °C | 15 µm/m·°C |
| Thermal conductivity at 20 °C | 11.5 W/m·K |
| Specific heat, 0–100 °C | 500 J/kg·K |
| Electrical resistivity | 952 nΩ·m |
| Magnetic response | non-magnetic |
| Pitting resistance equivalent | about 35 |

## Equivalent designations

| System | Designation |
|---|---|
| Japan, bar | SUS890L and SUS317J5L to JIS G4303 |
| Japan, plate and strip | SUS890L to JIS G4304 and JIS G4305 |
| Japan, tube and pipe | SUS890LTB to JIS G3463; SUS890LTP to JIS G3459 |
| United States | AISI 904L; ASTM 904L; forgings to ASTM A182 F904L |
| UNS | N08904 |
| EN | 1.4539, X1NiCrMoCu25-20-5 |
| United Kingdom | 904S13 to BS 1501/3; 904S14 to BS 1554 |
| Sweden | SS 2562 |
| South Korea | STS890L to KS D 3698, KS D 3705, KS D 3706 |
| Romania | 2CuMoCrNi250 to STAS 3583 |
| ISO | X1NiCrMoCu25-20-5 to ISO 16143 and ISO 9328-7 |
| Trade names | URANUS B6, NAS 255, FO 25-20 U, SOUDINOX B6 |

Equivalents are close but rarely identical; the ordering specification governs. Data on the Western designation is at https://www.steelforgepieces.com/Stainless-Steel/904L.html

## Forging route and heat treatment

Stock is melted by electric furnace with ladle refining and vacuum oxygen decarburisation, by vacuum induction, or by either route followed by vacuum arc or electroslag consumable remelting where the order calls for it. Billets are hot worked between roughly 950 and 1150 °C; working below 950 °C is avoided because the alloy stiffens and turns crack sensitive.

After forging the standard condition is solution treatment with rapid cooling. Mill datasheets give 1090 to 1175 °C. Where ASTM A182 governs, the sequence is to cool below 538 °C after hot working, solution treat at 1050 to 1150 °C, then liquid quench to below 260 °C. The grade cannot be hardened thermally; strength rises only through cold work, which should be removed by re-solution treating before stress corrosion cracking service.

Welding is possible by all standard processes with matching 904L electrodes and filler such as ER385 to AWS A5.9. The weld metal solidifies fully austenitic, so restrained joints are sensitive to hot cracking. No preheat, and post weld heat treatment is normally not required.

Machining follows standard methods with rigid setups, sharp tooling and positive feeds; the low sulphur content means it will not cut as freely as a free machining steel. Pickle and passivate after machining to restore the passive film.

## Corrosion behaviour and service limits

Developed for sulphuric acid, and also used in phosphoric and acetic acid, chloride bearing process water and warm seawater. Service limits depend on concentration, temperature, aeration and contaminants, so a corrosion chart or coupon test should settle borderline duties.

Against neighbouring grades: 316L costs far less but is well behind in acids and chlorides; duplex 2205 offers very similar corrosion resistance at higher strength and lower cost but is not suited above about 300 °C; 6 % Mo super austenitics give higher pitting and crevice resistance at higher cost; super duplex adds both higher corrosion resistance and higher strength; 304L and 310L are better in aggressive nitric acid, being molybdenum free.

The alloy has good oxidation resistance but its structural stability falls away above about 400 °C, so it is not a high temperature material. It stays tough into cryogenic service.

## Forged products in SUS 890L

Seamless rolled rings and forged rings; weld neck, blind, slip on and lap joint flanges to ASME B16.5, B16.47, EN 1092-1 or drawing; forged discs, tube sheets, covers and blanks; pump, agitator, eccentric and stepped shafts; forged round, square and hollow bars; sleeves, bushings and cylinders; valve bodies, bonnets, stems and seat rings; heavy wall forged pipe and tube sections.

Typical service: sulphuric, phosphoric and acetic acid plant, fertiliser production, pulp and paper processing, seawater cooling and desalination, tanker ballast system valves, downhole and wellhead equipment, gas scrubbing plant, heat exchangers, crystallisers, reactors, electrostatic precipitator components, and pharmaceutical and food processing equipment.

## Testing and certification

Ultrasonic testing to ASTM A388, EN 10228-3 or SEP 1921 as agreed on the order. Standard package: chemical analysis and PMI, tensile and proof strength with elongation, hardness, and dimensional inspection against the approved drawing. Intergranular corrosion testing to ASTM A262 or ASTM G28 and pitting testing to ASTM G48 are placed with an accredited laboratory and reported alongside the mill certificate; flag these at enquiry stage. Certificates to EN 10204 3.1, or 3.2 witnessed by TUV, SGS, BV, LR or DNV.

## The manufacturer

Jiangyin Jiangnan Metal Co., Ltd. is an integrated melting works and open-die forge at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China, operating since 1997. Steel is melted on site rather than bought as billet, so the certificate traces a part to its melt number. Maximum heat size 60 tonnes; 6,300 t, 4,000 t and 2,000 t hydraulic presses; radial-axial ring mills to 6,000 mm outside diameter; heaviest single forging 30 tonnes; 14 heat treatment furnaces and a machine shop on the same site. Class approvals CCS, BV, DNV, LR and NK. Minimum order 10 kg, no minimum piece count, lead time 20 to 60 days.

Enquiries: sales@steelforgepieces.com, 0086-189-2135-9659.

## Questions

**Is SUS 890L the same as 904L?** For practical purposes, yes. SUS890L is the JIS designation for the alloy known internationally as 904L, UNS N08904 and EN 1.4539. The composition ranges match; the product standard, test requirements and certificate wording differ.

**What is the UNS number?** N08904. EN 1.4539, X1NiCrMoCu25-20-5. In Korea, STS890L.

**Which JIS standards cover it?** G4303 bars, G4304 hot rolled plate and strip, G4305 cold rolled plate and strip, G3463 tube as SUS890LTB, G3459 pipe as SUS890LTP. Forgings are usually ordered to ASTM A182 F904L.

**What are the mechanical minimums?** 215 N/mm² proof stress, 490 N/mm² tensile, 35 % elongation, 90 HRB or 187 HB maximum.

**Can it be hardened by heat treatment?** No. It is fully austenitic. Strength rises only through cold work.

**Is it magnetic?** No.

**What is the PREN?** About 35.

**What is the largest forging?** Rings to 6,000 mm outside diameter, heaviest single piece 30 tonnes, subject to geometry and alloy.

**How do I get a price?** Email the drawing or rough sizes, quantity, specification and certificate requirement to sales@steelforgepieces.com, or call 0086-189-2135-9659.

Values are nominal and given for guidance; the purchase order and the governing specification take precedence.
