# SUS 310S Forgings

**SUS 310S is a 25Cr-20Ni heat-resisting austenitic stainless steel, the low-carbon member of the 310 family, known elsewhere as 310S, UNS S31008, EN 1.4845 and GB 06Cr25Ni20. Jiangyin Jiangnan Metal Co., Ltd. melts and forges it at an integrated works in Zhouzhuang Town, Jiangyin City, Jiangsu Province, China.**

The grade carries 24 to 26 percent chromium and 19 to 22 percent nickel with carbon capped at 0.08 percent. It holds a stable oxide scale in air to around 1050 C, which puts it in kilns, radiant tubes, retorts, muffles, annealing covers, furnace rolls and refinery internals. It is not a wet-corrosion alloy.

SUS 310S is melted here rather than bought in as billet. The route is electric arc furnace, ladle furnace, then vacuum oxygen decarburisation, which is the step that holds carbon under 0.08 percent without oxidising away the chromium the alloy depends on. Maximum heat size is 60 tonnes.

## Grade record

| Field | Detail |
|---|---|
| JIS | SUS 310S |
| ASTM and AISI | 310S |
| UNS | S31008 |
| EN | 1.4845, X8CrNi25-21 |
| GB, China | 06Cr25Ni20, formerly 0Cr25Ni20 |
| SS, Sweden | 2361 |
| Forging specification | ASTM A182 F310; JIS G 3214 SUSF310 |
| Type | Austenitic, heat resisting, not hardenable by heat treatment |
| Delivery condition | Solution annealed, 1040 to 1065 C, rapid cool |
| Melt route at this works | EF, LF, VOD. 60 t maximum heat |
| Maximum ring outside diameter | 6,000 mm |
| Maximum single piece | 30,000 kg |
| Minimum order | 10 kg, no minimum piece count |
| Lead time | 20 to 45 days for this grade |
| Certification | EN 10204 3.1, or 3.2 witnessed |

## Chemical composition, weight percent

| Element | SUS 310S / S31008 | 310 / S31000 | 310H / S31009 |
|---|---|---|---|
| Carbon, C | 0.08 max | 0.25 max | 0.04 to 0.10 |
| Manganese, Mn | 2.00 max | 2.00 max | 2.00 max |
| Silicon, Si | 1.50 max | 1.50 max | 0.75 max |
| Phosphorus, P | 0.045 max | 0.045 max | 0.045 max |
| Sulphur, S | 0.030 max | 0.030 max | 0.030 max |
| Chromium, Cr | 24.0 to 26.0 | 24.0 to 26.0 | 24.0 to 26.0 |
| Nickel, Ni | 19.0 to 22.0 | 19.0 to 22.0 | 19.0 to 22.0 |
| Iron, Fe | Balance | Balance | Balance |

Carbon is the only element separating the three grades. 310 allows up to 0.25 percent. 310S is capped at 0.08 percent, which is why it is specified where sensitisation and attack by hot gases or condensate matter. 310H uses a controlled 0.04 to 0.10 percent band for higher creep strength.

## Mechanical properties, solution annealed

| Property | Value |
|---|---|
| 0.2 percent proof stress | 205 MPa min |
| Tensile strength | 520 MPa min |
| Elongation | 40 percent min |
| Hardness | 225 HV max |

These are specification minima. On a heavy forging the governing values are those measured on a prolongation or sacrificial ring taken from the piece, since section size and sampling position both shift the result. Tested figures appear on the certificate.

## Physical properties

| Property | Condition | Value |
|---|---|---|
| Density | | 8,000 kg/m3 |
| Modulus of elasticity | 20 C | 200 GPa |
| Shear modulus | 20 C | 77 GPa |
| Poisson ratio | 20 C | 0.30 |
| Thermal conductivity | 100 C | 14.2 W/m.C |
| Coefficient of expansion | 0 to 100 C | 15.9 x 10-6 /C |
| Coefficient of expansion | 0 to 540 C | 17.0 x 10-6 /C |
| Specific heat | | 500 J/kg.C |
| Electrical resistivity | 25 C | 0.78 microhm.m |
| Relative magnetic permeability | | 1.02 |
| Melting range | | 1400 to 1450 C |

Sources differ slightly on this grade. Density is quoted as both 8,000 and 7,750 kg/m3, and the melting range as 1400 to 1450 C or 1354 to 1402 C. Where a calculation depends on it, use the figure from the governing standard.

## Service temperature

Grade 310 and 310S resist oxidation in air to approximately 1050 C continuous and 1035 C intermittent. Continuous service takes the higher figure because cyclic heating cracks and spalls the protective scale.

High chromium with medium nickel gives useful resistance in reducing sulphur atmospheres containing hydrogen sulphide, and the grade performs in the moderately carburising conditions of petrochemical plant. Severely carburising service calls for Incoloy 800HT, Inconel 601 or Haynes 230 instead. Frequent liquid quenching is not recommended, as the grade suffers thermal shock. At low temperature the austenitic structure makes it useful for cryogenic equipment, where toughness and low magnetic permeability both count.

**Sigma phase.** Time between roughly 650 C and 900 C precipitates sigma phase, a brittle intermetallic that removes ductility and impact toughness. It is reversible by re-solution annealing at about 1040 to 1150 C with rapid cooling, and operators running the grade through that band commonly re-anneal between campaigns. Sensitisation is a separate mechanism occurring around 550 to 800 C.

## Where 310S is the wrong choice

There is no molybdenum in this steel. Pitting resistance is poor despite the chromium level, and chloride stress corrosion cracking is a risk in chloride-bearing liquids above about 100 C. General corrosion resistance beats 304, but that does not make it a wet-service alloy. Where pitting, crevice attack or chloride cracking governs, move to 904L, a 6Mo grade such as ASTM A182 F44, or duplex grades F51, F53 and F55. All are forged at this works.

## Forging, heat treatment and machining

**Forging.** Working range 975 to 1175 C, with heavy reduction down to about 1050 C and light finishing below that. Some practice starts at 1150 to 1200 C and finishes above 950 C. Presses are 6,300 t, 4,000 t and 2,000 t, with 5 t, 3 t, 2 t, 1 t and 750 kg hammers. Rings roll on 6 m, 3 m and 1 m radial-axial mills, or are upset and punched from 50 mm outside diameter upward.

**Heat treatment.** Solution annealed, commonly 1040 to 1065 C soaked through section and cooled rapidly; wider windows of 1030 to 1150 C are also published. The grade cannot be hardened by heat treatment and has no ageing cycle. Because the soak runs above 1000 C, 310S goes into the high-temperature car-bottom furnaces, and furnace size rather than press capacity usually caps the size of a solution-annealed piece. Deep well-type furnaces allow long shafts to be treated vertically.

**Machining.** Similar to type 304. Work hardening is the issue: slow speeds, heavy positive cuts under the hardened skin, sharp tooling, good lubrication, rigid setups. Vertical lathes to 5,000 mm swing, horizontal lathes to 14 m between centres, deep-hole drilling to 1,600 mm diameter by 10,000 mm.

**Welding.** Matching consumables, AWS E310 electrodes or ER310 filler under argon. No preheat or post-heat needed. High-temperature service needs no post-weld treatment beyond slag removal. Wet corrosive service needs a full post-weld solution anneal plus pickling and passivation.

## Product forms and size envelope

| Forged form | Typical service | Size limit and what sets it |
|---|---|---|
| Seamless rolled rings, forged rings, retaining rings | Kilns, radiant tubes, muffles, retorts, annealing covers | OD 50 to 6,000 mm, set by the 6 m ring mill |
| Flanges, tube sheets, discs, covers | Heat exchangers, pressure vessels, air receivers | Up to 5,000 mm machined diameter |
| Shafts, spindles, rolls, eccentric shafts | Furnace rolls, conveyor rollers, fans, gearboxes, compressors | Up to 14,000 mm turned length |
| Hollow cylinders, sleeves, bushings, bored pipe | Saggers, oven linings, furnace internals | Up to 1,600 mm dia x 10,000 mm bored |
| Valve bodies, bonnets, stems, seat rings, nozzles | Gate, globe, ball, check and plug valves in hot gas service | Up to 30,000 kg single piece |
| Round bars, flat bars, blocks, blanks | Refinery FCC internals, food plant, cryogenic structures | From 10 kg minimum order |

## Testing and certification

The works holds CCS, BV, DNV, LR and NK approvals and runs its own laboratory.

| Test | Method | Where |
|---|---|---|
| Chemical analysis | ASTM E415 optical emission; ASTM E1019 carbon and sulphur | On site, at the furnace |
| Positive material identification | Handheld alloy analyser | On site |
| Tensile | ASTM A370 or ISO 6892, prolongation or sacrificial ring | On site |
| Impact | ASTM A370 Charpy V-notch to minus 60 C | On site; colder placed with an accredited laboratory |
| Ultrasonic | ASTM A388; EN 10228-4 for austenitic forgings | On site |
| Grain size | ASTM E112 | On site |
| Intergranular corrosion | ASTM A262 | Accredited third-party laboratory |

**On EN 10228-3 versus EN 10228-4.** Purchase specifications frequently call up EN 10228-3 for stainless forgings. That part covers ferritic and martensitic steel. The part written for austenitic and austenitic-ferritic stainless forgings is EN 10228-4, and that is the one matching SUS 310S. Raise it at enquiry stage so quality class and acceptance criteria are fixed before melting.

Magnetic particle inspection has no meaning on this grade, since solution-annealed 310S is non-magnetic at a relative permeability near 1.02. Liquid penetrant is the correct surface method.

## Frequently asked questions

### What is SUS 310S equivalent to?

SUS 310S is the JIS name for 25Cr-20Ni heat-resisting austenitic stainless steel. The same material is 310S to ASTM and AISI, S31008 in UNS, 1.4845 in the European system, 06Cr25Ni20 in Chinese GB, formerly 0Cr25Ni20, and SS 2361 in Sweden.

### What is the difference between 310, 310S and 310H?

Only carbon. Chromium holds at 24 to 26 percent and nickel at 19 to 22 percent across all three. 310 permits up to 0.25 percent carbon, 310S caps at 0.08 percent for resistance to sensitisation, and 310H uses 0.04 to 0.10 percent for creep strength.

### How hot can SUS 310S run?

About 1050 C continuous and 1035 C intermittent in air. Cyclic heating is harder on the oxide scale than steady service, which is why the intermittent figure is the lower one. Sulphur-bearing, low-oxygen, carburising and nitriding atmospheres all reduce the practical maximum.

### Can SUS 310S be hardened by heat treatment?

No. It is fully austenitic with no hardening response and no ageing cycle. Delivery condition is solution annealed, commonly 1040 to 1065 C with rapid cooling. Only cold work raises strength, which rarely applies to forgings.

### What is sigma phase embrittlement and can it be reversed?

Time between roughly 650 C and 900 C precipitates sigma phase, a brittle intermetallic that cuts ductility and impact toughness. Re-solution annealing at about 1040 to 1150 C with rapid cooling dissolves it back into the matrix and restores ductility.

### Is SUS 310S suitable for seawater or chlorides?

No. Without molybdenum its pitting resistance is poor, and chloride stress corrosion cracking is a risk above roughly 100 C in chloride-bearing liquid. Use 904L, A182 F44, or duplex F51, F53 or F55 instead.

### Which ultrasonic standard should be specified?

ASTM A388, or EN 10228-4 in the European system, which covers austenitic and austenitic-ferritic stainless forgings. EN 10228-3 applies to ferritic and martensitic forgings.

### What is the largest SUS 310S forging available?

Rings to 6,000 mm outside diameter, single pieces to 30 tonnes, against a 60 t maximum heat. For this grade the solution-annealing furnace, not the press, usually sets the ceiling, because the soak runs above 1000 C. Send dimensions and the treatable size will be confirmed before quoting.

### Do you melt the steel or buy billet?

It is melted here, through the electric arc furnace, ladle furnace and vacuum oxygen decarburisation. The certificate traces the part to its melt number rather than to a purchased billet.

### Is there a minimum order quantity and what is the lead time?

Minimum order is 10 kg with no minimum piece count. Normal lead time for this grade is 20 to 45 days, within the works range of 20 to 60 days. Witnessed EN 10204 3.2 inspection and outside laboratory corrosion testing need scheduling, so state them with the enquiry.

## Contact

**Jiangyin Jiangnan Metal Co., Ltd.**
No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Telephone, WhatsApp and WeChat: +86 189 2135 9659
Email: sales@steelforgepieces.com
Business hours: Monday to Saturday, 08:00 to 17:30 China Standard Time, UTC+8
Web page: https://www.steelforgepieces.com/Stainless-Steel/SUS-310S.html

Quotations need six items: grade or specification, dimensions or drawing, quantity, delivery condition, heat treatment and testing requirements, certification and destination port.

---

Copyright 1997 to 2026 Jiangyin Jiangnan Metal Co., Ltd. Integrated melting works and open-die forging factory, Jiangyin, Jiangsu, China.
