# SUH 310 Forgings

**SUH 310 is the Japanese heat-resisting austenitic stainless steel with 24.0 to 26.0 percent chromium and 19.0 to 22.0 percent nickel, carbon to 0.25 percent. It is listed in JIS G 4311 for heat-resisting bars and wire rods and JIS G 4312 for plate, sheet and strip, and corresponds to AISI 310 and UNS S31000.**

Jiangyin Jiangnan Metal Co., Ltd. melts this grade on site at Zhouzhuang Town, Jiangyin City, Jiangsu Province, China, then forges or ring-rolls it to drawing. The certificate traces a part back to its melt number rather than to a purchased billet.

The chromium builds a tenacious oxide and the nickel holds the structure austenitic at temperature. That combination is why the grade appears in furnace hardware, carburising boxes and heat-treatment baskets, and why it is the wrong choice for chloride service.

## Grade record

| Field | Detail |
|---|---|
| Grade | SUH 310 |
| Standards | JIS G 4311, JIS G 4312 |
| UNS | S31000 |
| Type | Austenitic, heat resisting, non-magnetic |
| Density | 7.98 g/cm3 |
| Maximum single piece | 30 t |
| Maximum rolled ring OD | 6,000 mm |
| Minimum order | 10 kg, no minimum piece count |
| Lead time | 20 to 60 days |
| Manufacturer | Jiangyin Jiangnan Metal Co., Ltd. |
| Plant | No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China |
| Telephone | +86 189 2135 9659 |
| Email | sales@steelforgepieces.com |
| Business hours | Monday to Saturday, 08:00 to 17:30 China Standard Time |
| Page | https://www.steelforgepieces.com/Stainless-Steel/SUH-310.html |

## Chemical composition

Weight percent, JIS G 4311 and G 4312. Iron balance.

| C | Si | Mn | P | S | Ni | Cr |
|---|---|---|---|---|---|---|
| 0.25 max | 1.50 max | 2.00 max | 0.040 max | 0.030 max | 19.0 to 22.0 | 24.0 to 26.0 |

Molybdenum and copper are not specified elements for this grade in JIS. Where a purchase specification sets residual ceilings, we hold them at the melt. UNS S31000 allows phosphorus to 0.045 percent, looser than the JIS 0.040 limit, so an ASTM-certified part does not automatically satisfy a JIS chemistry check.

## Mechanical properties

Room temperature, solution treated bar.

| Property | JIS minimum | Typical published range, AISI 310 annealed |
|---|---|---|
| Proof stress Rp0.2 | 205 MPa | 205 to 310 MPa |
| Tensile strength Rm | 590 MPa | 500 to 620 MPa |
| Elongation A | 40 % | 30 to 47 % |
| Reduction of area Z | 50 % | - |
| Hardness | 201 HBW max | 185 to 207 HB |
| Fatigue strength at 10^7 cycles | - | 206 to 228 MPa |
| Modulus of elasticity | - | 196 to 204 GPa |

Older JIS data gives 40 percent minimum elongation; the 2019 edition of G 4311 is published with 45 percent minimum for the solution treated condition. State the edition that governs the order.

A part ordered to ASTM A182 F310 and the same part ordered to JIS SUH 310 are not interchangeable on paper. The ASTM and ASME route for 310 and 310S is commonly written around 515 to 520 MPa minimum tensile with 205 MPa proof stress and 40 percent elongation, below the 590 MPa the JIS bar standard requires.

## Physical properties

| Property | Value |
|---|---|
| Density | 7.98 g/cm3 |
| Melting range | 1400 to 1450 C |
| Maximum service temperature | 1050 to 1150 C published range |
| Minimum service temperature | -200 C |
| Thermal conductivity | 11 to 16 W/m.C |
| Specific heat capacity | 490 to 530 J/kg.C |
| Coefficient of thermal expansion | 15 to 17 micrometre/m.C |
| Electrical resistivity | 72 to 90 microhm.cm |
| PREN | 24 to 26 |
| Magnetic response | Non-magnetic in the solution treated condition |

At 15 to 17 micrometres per metre per degree, a 2 metre furnace ring grows close to 30 mm on the way to 1000 C. Clearances need drawing for the hot condition.

## Equivalent grades

| Country or body | Designation | Specification |
|---|---|---|
| Japan | SUH 310 | JIS G 4311, JIS G 4312 |
| United States | AISI 310, UNS S31000, F310 forgings | ASTM A182, A336, A965, A276 |
| Europe | X15CrNi 25-20 (1.4845), X15CrNiSi 25-20 (1.4841) | EN, DIN |
| China | 20Cr25Ni20, 2Cr25Ni20, S31020 | GB |
| South Korea | STR 310 | KS |
| United Kingdom | 310S31 | BS |
| France | Z15CNS 25-20 | NF |
| Russia | 20Kh25N20S2 | GOST |
| ISO | X15CrNi 25-21 | ISO |

These are close matches, not drop-in substitutions. Silicon separates 1.4841 from 1.4845 and changes scaling behaviour at the top of the range.

### SUH 310 against 310S

Chromium and nickel are the same, so the oxidation ceiling near 1150 C is the same. Carbon differs. 310S is held lower and welds more easily. The higher carbon allowed in 310 and SUH 310 earns better strength at temperature. Welded assembly, specify 310S. Standalone hot part, specify SUH 310.

## Forging and heat treatment

| Operation | Practice |
|---|---|
| Melting | EF, LF and VOD. ESR remelt where cleanliness or segregation control is specified. |
| Forging | 6,300 t, 4,000 t or 2,000 t press. Radial-axial ring rolling on the 6 m, 3 m or 1 m mill. |
| Solution treatment | 1050 to 1150 C, soak by section thickness, then rapid quench. |
| Quench | Water as standard. Thin or complex sections quenched to control distortion, route agreed in advance. |
| Records | Furnace charts recorded against the heat treatment lot and issued with the certificate. |

On welding, published ratings for AISI 310 are fair rather than good for TIG, MIG and plasma, submerged arc is listed as not recommended, and high-silicon 25Cr-20Ni austenitics are noted as sensitive to weld hot cracking. No preheat or post-weld heat treatment is needed and matching filler is normal, but fabrication after forging should be planned around those limits.

## Shapes and working envelope

| Form | Items | Size limit |
|---|---|---|
| Seamless rolled rings | Rectangular and contoured section, gear ring blanks, slewing rings | to OD 6,000 mm |
| Forged rings | Upset and punched rings, retaining rings, valve seat rings | from OD 50 mm |
| Flanges | Weld neck, blind, slip-on, lap joint, orifice, long weld neck blanks | to 5,000 mm machined dia |
| Discs and tube sheets | Solid discs, tube sheets, covers, proof-machined for volumetric inspection | to 5,000 mm machined dia |
| Bars and blocks | Round, flat and square bars, blocks for machined bodies | by drawing |
| Shafts and spindles | Stepped shafts, pinion shafts, rolls, rotors, tie rods | to 14,000 mm turned length |
| Cylinders and sleeves | Hollow cylinders, sleeves, bushings, heavy-wall pipe bored from solid | to 1,600 mm dia x 10,000 mm |
| Valve parts | Bodies, bonnets, stems, seat rings, nozzles, manifolds | by drawing |
| Single piece weight | Set by the 60 t heat size and the 6,300 t press | to 30,000 kg |

## Where SUH 310 is used

Documented uses are furnace parts, carburising boxes, heat-treatment baskets and jigs, oil burner parts, heat exchangers, electrical parts, and welding filler wire and electrodes. In forged form the common items are furnace rolls and roller-hearth hardware, kiln and annealing line fixtures, burner and combustion chamber components, radiant tube flanges and supports, thermal oxidiser internals, and reformer and cracking furnace hardware.

Not for seawater or sour service. AISI 310 rates moderate in both, PREN sits around 24 to 26, and there is slight susceptibility to chloride stress corrosion cracking. For those duties see A182 F51, F53 and F55 duplex, 904L, A182 F44 or Incoloy 825. For hotter or more carburising service see AISI 330, Incoloy 800H, Inconel 601 or Inconel 617.

## Testing and certification

| Item | Standard or scope |
|---|---|
| Ultrasonic examination | EN 10228-3, SEP 1921 or ASTM A388, class as ordered |
| Chemical analysis | Ladle and product analysis against the governing specification |
| Mechanical testing | Tensile, hardness, impact where specified, test location agreed in advance |
| Metallurgical | Grain size, intergranular corrosion testing where required |
| Certification | EN 10204 3.1, or 3.2 witnessed by a third party |
| Works approvals | CCS, BV, DNV, LR, NK |

## Questions

**What is SUH 310 steel?** A Japanese heat-resisting austenitic stainless steel, 24.0 to 26.0 percent chromium, 19.0 to 22.0 percent nickel, carbon to 0.25 percent, covered by JIS G 4311 and G 4312. JIS counterpart of AISI 310 and UNS S31000.

**What is it equivalent to?** UNS S31000 and AISI 310, 1.4845 or 1.4841 in Europe, 20Cr25Ni20 in China, STR 310 in South Korea, 310S31 in Britain, 20Kh25N20S2 in Russia. Forging specifications: ASTM A182 F310, A336 F310, A965 F310.

**How hot can it run?** Oxidation resistance in dry air to roughly 1150 C, with published maximum service figures spanning 1050 to 1150 C. Around 1035 C is the figure usually applied to intermittent service, because thermal cycling makes the scale spall.

**Is it magnetic?** No. Austenitic and classed as non-magnetic. Heavy cold work can raise a slight response.

**310 or 310S?** Carbon is the only real difference. 310S welds more easily, 310 holds strength better at temperature.

**Seawater or sour service?** Not recommended. Moderate ratings, PREN 24 to 26, slight chloride stress corrosion cracking susceptibility. Use duplex, 904L, A182 F44 or a nickel alloy.

**How small or large?** From 10 kg with no minimum piece count to a 30 tonne single piece.

**How to get a price?** Email the drawing in PDF, DWG or STEP to sales@steelforgepieces.com, or call +86 189 2135 9659. Include quantity, governing specification, delivery condition, NDT class and certificate level.

---

Jiangyin Jiangnan Metal Co., Ltd. | No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China | +86 189 2135 9659 | sales@steelforgepieces.com | Monday to Saturday, 08:00 to 17:30 China Standard Time
