# ASTM A182 F6B Forgings (UNS S41026)

**ASTM A182 Grade F6B, UNS S41026, is a martensitic stainless steel forging grade** containing 11.5 to 13.5 % chromium, 0.40 to 0.60 % molybdenum and 1.00 to 2.00 % nickel. It is supplied hardened and tempered to 110 to 135 ksi (760 to 930 MPa) tensile strength, 90 ksi (620 MPa) minimum yield strength and 235 to 285 HBW.

Jiangyin Jiangnan Metal Co., Ltd. melts and forges F6B in one works at Zhouzhuang Town, Jiangyin City, Jiangsu Province, China, so the certificate traces back to the melt number rather than to a purchased billet. Also designated ASME SA-182 F6B.

## Grade summary

| Field | Value |
|---|---|
| Grade | ASTM A182 F6B |
| UNS | S41026 |
| ASME equivalent | SA-182 F6B |
| Family | Martensitic stainless, hardenable, magnetic |
| Chromium | 11.5 - 13.5 % |
| Molybdenum | 0.40 - 0.60 % |
| Nickel | 1.00 - 2.00 % |
| Tensile strength | 110 - 135 ksi (760 - 930 MPa) |
| Yield strength, min | 90 ksi (620 MPa) |
| Brinell hardness | 235 - 285 HBW |

## Grade family

F6B is regularly listed on trade sites as a super-austenitic or 6Mo stainless steel. That description is wrong, and it leads to the grade being specified for duties it cannot survive.

F6B is martensitic. With 11.5 to 13.5 % chromium and only 1.00 to 2.00 % nickel there is nowhere near enough nickel to hold austenite at room temperature, so the structure transforms on cooling and the grade is magnetic and hardenable. Strength comes from the quench and temper, not from alloy content, and its corrosion resistance sits well below the austenitic, duplex and 6Mo families.

**Check before specifying.** If the enquiry mentions seawater, desalination, flue gas desulphurisation or pulp and paper digesters, F6B is the wrong grade. Those duties belong to A182 F44, F51, F53 or the nickel alloys.

## Chemical composition

Weight %. Values are maxima unless a range is shown.

| Element | Limit | Purpose |
|---|---|---|
| Carbon | 0.15 max | Hardenability and tempered strength |
| Manganese | 1.00 max | Deoxidation and sulphur control |
| Phosphorus | 0.020 max | Held low against temper embrittlement |
| Sulphur | 0.020 max | Held low for transverse toughness |
| Silicon | 1.00 max | Deoxidation |
| Nickel | 1.00 - 2.00 | Hardenability and toughness above plain 13Cr |
| Chromium | 11.5 - 13.5 | Passive film and corrosion resistance |
| Molybdenum | 0.40 - 0.60 | Temper resistance and localised corrosion |
| Copper | 0.50 max | Residual limit |
| Iron | Balance, about 81.2 - 87.1 | Base |

Chemistry is verified at the furnace on site by optical emission spectrometry to ASTM E415.

## Mechanical requirements

F6B has one strength level and is not divided into classes.

| Property | Imperial | Metric |
|---|---|---|
| Tensile strength | 110 - 135 ksi | 760 - 930 MPa |
| Yield strength, min | 90 ksi | 620 MPa |
| Elongation in 2 in. [50 mm] or 4D, min | 16 % | 16 % |
| Reduction of area, min | 45 % | 45 % |
| Brinell hardness | 235 - 285 HBW | about 22 - 30 HRC |

## Physical and engineering data

Published reference values for the annealed condition, for design screening only.

| Property | Value |
|---|---|
| Elastic (Young's) modulus | 190 GPa (28 x 10^6 psi) |
| Shear modulus | 76 GPa (11 x 10^6 psi) |
| Shear strength | 530 MPa (76 x 10^3 psi) |
| Fatigue strength | 440 MPa (63 x 10^3 psi) |
| Poisson's ratio | 0.28 |
| Thermal conductivity | 25 W/m.K (14 BTU/h.ft.F) |
| Thermal expansion | 10 um/m.K |
| Specific heat capacity | 480 J/kg.K |
| Melting range | 1400 - 1450 C |
| Maximum temperature, corrosion | 390 C (730 F) |
| Maximum temperature, mechanical | 750 C (1390 F) |
| Electrical conductivity | 2.8 % IACS |
| Magnetic response | Ferromagnetic |

## Delivery condition and heat treatment

F6B is hardenable, so the delivery condition decides the properties received. ASTM A182 permits liquid quench followed by tempering for martensitic grades. The austenitising and tempering cycle is set out in the heat treatment table of the standard, and we work to the edition named on the purchase order.

| Condition | Yield MPa | Tensile MPa | Elongation | Hardness | Used for |
|---|---|---|---|---|---|
| Annealed | 320 | 540 | 28 % | 175 HB | Rough machining and deep hole drilling before final quench and temper. Not a code delivery condition for F6B. |
| Normalised and tempered | 600 | 780 | 20 % | 24 HRC | Air cooled route for heavy sections where oil quenching risks cracking. |
| Quenched and tempered | 660 | 810 | 20 % | 26 HRC | Standard condition for F6B flanges, valve bodies and fittings. |
| Quenched and tempered, high strength | 800 | 950 | 16 % | 31 HRC | Where the part must match a 130 ksi class body or trim. |

**Specification error screened at order entry.** Several datasheets in circulation quote an anneal at 2100 to 2150 F with a water quench for F6B. That is a solution anneal belonging to super-austenitic grades. Applied to a 13Cr martensitic forging it would leave the part far outside the specified strength and hardness band.

## Corrosion behaviour and limits

F6B forms a passive chromium oxide film and gives useful service in fresh water, steam, dry gas, crude oil and mild organic media. Molybdenum improves temper resistance and localised corrosion behaviour compared with plain 13Cr, and nickel raises hardenability and toughness compared with A182 F6A.

Published data puts the maximum corrosion service temperature at about 390 C. With 13 % chromium and 0.5 % molybdenum this is not a chloride or seawater material. Pitting in chloride-bearing media and cracking risk at the upper end of the hardness band are the two failure modes to design against.

### Sour service, NACE MR0175 and ISO 15156

F6B can go into sour service only on a restricted hardness specification. A general 22 HRC limit applies to many materials in H2S-bearing service, which sits at the bottom of the 235 to 285 HBW band F6B is normally supplied to, so much of the standard range is above the general cap. Certain martensitic stainless steels are allowed higher limits under specific clauses of the standard.

Send the H2S partial pressure, temperature, chloride concentration and in-situ pH with the enquiry.

## Grade comparison

| Grade | UNS | Family | Cr / Mo / Ni | Strength | Role |
|---|---|---|---|---|---|
| F6B | S41026 | Martensitic | 11.5-13.5 / 0.40-0.60 / 1.0-2.0 | 110-135 ksi | Trim, stems, high strength flanges |
| F6A | S41000 | Martensitic | 13Cr, no specified Mo | 70-130 ksi by class | General 13Cr fittings |
| F6NM | S41500 | Soft martensitic | 13Cr / Mo / 4Ni | - | Where weld and impact toughness govern |
| F51 | S31803 | Duplex | 22Cr / 3Mo / 5Ni | - | Chloride-bearing process duty |
| F53 | S32750 | Super duplex | 25Cr / 4Mo / 7Ni | - | Seawater and subsea |
| F44 | S31254 | Super-austenitic 6Mo | 20Cr / 6Mo / 18Ni | - | Seawater, FGD, desalination |

## What we forge in F6B

- **Valve and wellhead parts.** Bodies, bonnets, stems, seat rings, plugs, gates and wedges for ball, gate, globe, check and plug valves in non-chloride service.
- **Forged flanges.** Weld neck, blind, slip-on, socket weld, lap joint and orifice flanges to ASME B16.5, B16.47 and API 6A dimensions.
- **Seamless rolled rings.** Radial-axial rolled rings from OD 50 mm to OD 6,000 mm for bearing carriers, retaining rings and pressure boundary blanks.
- **Shafts and bars.** Pump and compressor shafts, spindles, stems and tie rods, turned to 14,000 mm between centres, quenched vertically in the 15 m well furnaces.
- **Discs and tube sheets.** Solid forged discs, covers and tube sheet blanks to 5,000 mm machined diameter, supplied proof-machined for volumetric inspection.
- **Sleeves and bushings.** Wear sleeves, bushings, liners and bored cylinders to 1,600 mm diameter by 10,000 mm on the deep-hole drilling machine.

## Fabrication notes

**Forging.** Hot work in the usual martensitic stainless range and finish above the point where the grade begins to harden on cooling, then slow cool or anneal straight away so untempered martensite does not crack the piece. The forging is cooled below the temperature set in A182 before the specified heat treatment.

**Machining.** Rough machine in the annealed condition wherever the drawing allows, then finish after quench and temper. In the hardened condition use rigid setups, sharp carbide tooling and heavy positive feeds so the tool cuts under the work-hardened layer instead of glazing it.

**Welding.** Weldable with care. Preheat with a controlled interpass temperature, a matching 13Cr or 13Cr-4Ni filler, or an austenitic filler where softer weld metal is acceptable, then a post-weld temper to soften the heat affected zone. Where weld toughness governs, F6NM is the usual alternative.

## Manufacturing and quality

Steel for F6B is melted on site rather than bought in as billet, so the chemistry can be aimed at the forging it will become and the certificate traces back to the melt number.

| Step | Capability |
|---|---|
| Melting | 25 t electric arc furnace, 25 t and 50 t ladle furnaces, 30 t and 60 t VOD. Maximum heat 60 t. ESR available where cleanliness governs. |
| Forging | 6,300 t, 4,000 t and 2,000 t hydraulic open-die presses. Hammers 750 kg to 5 t. Maximum single piece 30 t. |
| Ring rolling | Radial-axial mills at 6 m, 3 m and 1 m. Maximum OD 6,000 mm, minimum from OD 50 mm by upset and punch. |
| Heat treatment | 14 furnaces. Car-bottom chambers to 8,000 x 2,000 x 2,000 mm, two well furnaces 15,000 mm deep for vertical quenching. |
| Machining | Vertical lathes to 5,000 mm swing, horizontal lathes to 14 m, CNC to 2,000 mm dia x 10,000 mm, deep-hole drilling to 1,600 mm dia x 10,000 mm. |
| Chemistry | Optical emission spectrometry to ASTM E415, carbon and sulphur to ASTM E1019, handheld PMI. |
| Mechanical testing | 600 kN and 300 kN universal machines to ASTM A370 and ISO 6892. Charpy V-notch to -60 C. |
| Ultrasonic testing | ASTM A388 and EN 10228-3. Magnetic particle to ASTM E709. Grain size to ASTM E112. |
| Approvals | CCS, BV, DNV, LR, NK. |
| Certification | EN 10204 3.1, or EN 10204 3.2 witnessed by BV, DNV, LR, SGS, TUV or the customer's inspector. |
| Order terms | Minimum order 10 kg, no minimum piece count. Lead time 20 to 60 days. |

## Frequently asked questions

### Is ASTM A182 F6B austenitic or martensitic?
Martensitic. UNS S41026 carries 11.5 to 13.5 % chromium with only 1.0 to 2.0 % nickel, far below what is needed to hold austenite at room temperature. It is magnetic and hardenable by heat treatment. Listings that call it super-austenitic or 6Mo are incorrect.

### What is the difference between A182 F6A and A182 F6B?
F6A is UNS S41000, close to forged Type 410, with no specified molybdenum. F6B is UNS S41026 and adds 0.40 to 0.60 % molybdenum and 1.00 to 2.00 % nickel, with phosphorus and sulphur both held to 0.020 % maximum. F6A is supplied in several strength classes. F6B has one level at 110 to 135 ksi tensile and 235 to 285 HBW.

### What are the mechanical properties of F6B?
Tensile 110 to 135 ksi (760 to 930 MPa), yield 90 ksi (620 MPa) minimum, elongation 16 % minimum in 2 in. or 4D, reduction of area 45 % minimum, hardness 235 to 285 HBW.

### Can F6B be used in seawater or a desalination plant?
No. It is a 13 % chromium grade with 0.5 % molybdenum and a published maximum corrosion service temperature of about 390 C, and it will pit in chloride-bearing water. Use F44, F51 or F53.

### Is F6B acceptable under NACE MR0175 and ISO 15156?
Conditionally, on a restricted hardness specification. The general 22 HRC sour service limit sits at the bottom of the standard 235 to 285 HBW band, so restricted hardness heat treatment and hardness testing must be specified at order.

### Is UNS S41026 the same material as A182 F6B?
Yes. S41026 is the UNS designation for A182 Grade F6B. The ASME pressure vessel designation is SA-182 F6B.

### What is the largest F6B forging you can produce?
Seamless rings roll to 6,000 mm outside diameter on the 6 m radial-axial mill, with 3 m and 1 m mills for smaller sizes. The heaviest single forging is 30 tonnes, worked on 6,300 t, 4,000 t and 2,000 t presses, and maximum heat size is 60 tonnes. Minimum order is 10 kg with no minimum piece count.

### Do you supply finish-machined F6B parts or rough forgings only?
Both. Parts can be supplied as-forged with machining allowance, rough-machined to a proof-machined condition suitable for ultrasonic testing, or finish-machined to drawing.

## Request a quotation

Send the grade and edition (ASTM A182 F6B or ASME SA-182 F6B), the drawing or rough dimensions, the quantity, the delivery condition, the heat treatment and testing requirements, the certificate level and the destination port. If the duty is sour or chloride bearing, add the service conditions. Quotations normally go out within two working days.

**Jiangyin Jiangnan Metal Co., Ltd.**
No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Telephone, WhatsApp and WeChat: +86 189 2135 9659
Email: sales@steelforgepieces.com
Page: https://www.steelforgepieces.com/Stainless-Steel/A182-F6B.html
Business hours: Monday to Saturday, 08:00 to 17:30 China Standard Time (UTC+8)

---

Composition and mechanical requirements are those of ASTM A182/A182M for Grade F6B, UNS S41026. Physical property values are published reference data for the annealed condition. Delivery condition property levels are published supplier data. Sour service limits follow NACE MR0175 and ISO 15156. Verify against the current edition of the governing standard. Nothing on this page is a material certification.

Copyright 1997 to 2026 Jiangyin Jiangnan Metal Co., Ltd.
