# ASTM A182 F310MoLN Forgings (UNS S31050 / EN 1.4466)

Source: https://www.steelforgepieces.com/Stainless-Steel/A182-F310MoLN.html
Supplier: Jiangyin Jiangnan Metal Co., Ltd., integrated melting works and open-die forging factory, operating since 1997
Address: No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China, postcode 214423
Telephone, WhatsApp and WeChat: +86 189 2135 9659
Email: sales@steelforgepieces.com
Business hours: Monday to Saturday, 08:00 to 17:30 China Standard Time (UTC+8)
Approvals: CCS, BV, DNV, LR, NK
Revised: 29 September 2026

ASTM A182 F310MoLN is the forging grade for UNS S31050, a fully austenitic 25 % chromium,
22 % nickel stainless steel modified with molybdenum and nitrogen and held to extra low
carbon. It was developed for urea and ammonium carbamate service.

The grade needs two things at the furnace at the same time: carbon driven down to 0.030 %
or lower, and nitrogen held inside a 0.10 to 0.16 % window. Both are vacuum oxygen
decarburisation work. Jiangyin Jiangnan Metal melts its own steel on 30 t and 60 t VOD
units, so the chemistry is aimed at the forging rather than accepted as delivered, and the
certificate traces the part to its melt number instead of a purchased billet.

## At a glance

- Designations: F310MoLN (ASTM A182), UNS S31050, EN 1.4466, X1CrNiMoN25-22-2,
  AISI 310MoLN, TP310MoLN, BS 725LN, UREA 25.22.2, Z1CND25-22Az, 022Cr25Ni22Mo2N.
- Composition to ASTM A182: 24.0-26.0 % Cr, 21.0-23.0 % Ni, 2.00-3.00 % Mo,
  0.10-0.16 % N, carbon 0.030 % max, balance iron.
- Mechanical minimums to ASTM A182: 78 ksi (540 MPa) tensile, 37 ksi (255 MPa) yield,
  25 % elongation, 40 % reduction of area.
- Heat treatment: solution anneal then rapid cooling in water. Published ranges differ by
  source, so the customer specification governs.
- Forging range: about 1150 C down to a finish not below 850 C.
- Why specified: resistance to urea and carbamate at high pressure and temperature,
  resistance to intergranular corrosion after welding, and considerably better crevice
  corrosion resistance than 316L.
- Size envelope: seamless rolled rings OD 50 to 6,000 mm, single piece to 30,000 kg.
- Minimum order: 10 kg, no minimum piece count. Lead time 20 to 60 days.
- Certification: EN 10204 3.1 standard, 3.2 witnessed on request.

## What A182 F310MoLN is

A fully austenitic stainless steel, which means no intermetallic phases and no
intergranular carbide precipitation in the solution annealed condition. The composition
was optimised for urea plants.

Nitrogen at 0.10 to 0.16 % stabilises and strengthens the austenitic phase. That is what
allows carbon to sit down in the 0.020 to 0.030 % range without giving up strength, and it
is the extra low carbon that keeps the grain boundaries clean after welding. The two
additions work together, which is why nitrogen carries a floor in the specification and
not just a ceiling.

The alloy was developed for stripper tubes in urea production. High pressure carbamate is
among the harshest environments in chemical process plant, and the 25Cr-22Ni-2Mo-N balance
holds up there where 316L does not. The higher nickel content also gives it an edge over
304 and 316 against chloride stress corrosion cracking, which those grades become
susceptible to above roughly 60 C.

Two limits belong in the design decision. Among wrought austenitic stainless steels this
grade carries a fairly high base cost and fairly low ductility. It also has low thermal
conductivity and high thermal expansion, which matters for weld distortion and for heat
exchanger design.

## Chemical composition, weight percent, balance iron

| Element | ASTM A182 F310MoLN (S31050) | EN 1.4466 (X1CrNiMoN25-22-2) | Function in this grade |
|---|---|---|---|
| Carbon, C | 0.030 max | 0.020 max | Held extra low to stop carbide precipitation at grain boundaries |
| Silicon, Si | 0.40 max | 0.70 max | Deoxidiser |
| Manganese, Mn | 2.00 max | 2.00 max | Austenite stabiliser, raises nitrogen solubility |
| Phosphorus, P | 0.030 max | 0.025 max | Residual, restricted |
| Sulphur, S | 0.015 max | 0.010 max | Residual, restricted to protect hot workability and corrosion behaviour |
| Chromium, Cr | 24.0-26.0 | 24.0-26.0 | Primary passive film former, carbamate and nitric acid resistance |
| Nickel, Ni | 21.0-23.0 | 21.0-23.0 | Fully austenitic structure, chloride SCC resistance |
| Molybdenum, Mo | 2.00-3.00 | 2.00-2.50 | Pitting and crevice corrosion resistance |
| Nitrogen, N | 0.10-0.16 | 0.10-0.16 | Austenite stabiliser and strengthener, permits the low carbon level |

A separate cross-reference source states the ASTM S31050 ranges differently, giving
C 0.025 max, Si 0.50 max, P 0.020 max, S 0.030 max, Mo 1.6-3.0 %, Ni 20.5-23.5 % and
N 0.09-0.16 %. Confirm against the edition of the standard named on the order. Each heat
ships with its own certificate of analysis, and the certificate governs.

## Mechanical properties, solution annealed

| Property | ASTM A182 minimum | Typical, 310MoLN / 1.4466 |
|---|---|---|
| Tensile strength Rm | 78 ksi (540 MPa) | 540-740 MPa |
| Yield / proof strength Rp0.2 | 37 ksi (255 MPa) | about 250 MPa |
| Elongation, 2 in. (50 mm) or 4D | 25 % | reported at 40 % |
| Reduction of area | 40 % | not stated in sources |
| Modulus of elasticity at 20 C | not specified | 195 GPa |

Impact, transverse and quarter-radius testing can be specified on the order. Charpy
V-notch testing runs in house to minus 60 C on a 600 kN and a 300 kN machine. Published
elevated-temperature and physical data vary between sources and are issued with a
quotation rather than stated here.

## Corrosion behaviour of UNS S31050

| Mechanism | Behaviour |
|---|---|
| General corrosion | Strong resistance in urea and carbamate at high pressure and temperature, and to inorganic acids including nitric acid |
| Intergranular corrosion | Highly resistant after welding, from the extra low carbon and fully austenitic structure |
| Pitting | Very good, from combined Cr, Mo and N |
| Crevice corrosion | Considerably more resistant than 316L |
| Stress corrosion cracking | 304 and 316 become susceptible in chlorides above about 60 C; higher nickel makes S31050 slightly more resistant |
| Erosion corrosion | Good, relied on for urea stripper ferrules |
| Weldability | Good, no preheat, normally no post weld heat treatment; low conductivity and high expansion need distortion control |

Intergranular corrosion testing to ASTM A262 or ASTM G28, and pitting resistance to
ASTM G48, are placed with an accredited third-party laboratory and reported alongside the
mill certificate.

## Heat treatment and hot working

| Operation | Temperature | Cooling | Purpose |
|---|---|---|---|
| Solution annealing | 1050-1100 C (1920-2010 F) per supplier data; higher ranges to about 1150 C appear in other datasheets | rapid cooling in water or air, by section | Dissolve precipitates, restore the fully austenitic structure and full corrosion resistance |
| Soak time | 5-15 min thin section, extended by thickness | not applicable | Full solutionising through section |
| Forging | start about 1150 C, finish not below 850 C | air or controlled cool | Break down the cast structure, develop grain flow |
| Post weld heat treatment | normally not required | not applicable | Extra low carbon prevents sensitisation |

Published solution-anneal ranges for this grade are not consistent between sources. Where
the customer specification names a range, that range is used, and the heat-treatment chart
is issued with the certificate.

The quench matters as much as the soak. A slow cool through the intermediate band gives
precipitates time to form at the grain boundaries, which is exactly what the low carbon
and the nitrogen addition were meant to prevent. On heavy sections that means water
quenching with real agitation, and it means sizing the charge so nothing stands waiting at
the furnace door. Fourteen heat-treatment furnaces are on site, including two well-type
furnaces 15 m deep that let long shafts quench vertically rather than laid down.

## Equivalents and other designations

| Standard or origin | Designation | Note |
|---|---|---|
| ASTM A182 | F310MoLN | The forging grade symbol |
| UNS | S31050 | Primary US number. S35115 also appears in cross-reference lists |
| EN 10088 | 1.4466, X1CrNiMoN25-22-2 | European equivalent, tighter on C, P, S and Mo |
| AISI | 310MoLN, TP310MoLN | Common trade designation |
| BS | 725LN | British designation |
| NF, France | Z2CND25-22Az, Z1CND25-22Az | French designation |
| GB, China | 022Cr25Ni22Mo2N | Chinese designation |
| GOST, Russia | 02Ch25N22AM2 | Narrower nitrogen range, 0.10-0.14 % |
| SEW 400 | 1.4465, X1CrNiMoN25-25-2 | Related higher nickel variant, 22.0-25.0 % Ni |
| Mill designations | UREA 25.22.2, 25.22.2 LMn, 2RE69, 2RM69 WB, DMV 25.22.2, X2CrNiMoN25-22-2 | Proprietary names within the same alloy family |

Acceptance criteria, permitted residuals, testing requirements and pressure equipment
approval differ between standards. This is a cross reference, not a certified substitution
table. Confirm any substitution with your design authority before ordering.

## Forged product forms and size envelope

| Product form | Also called | Limit | Set by |
|---|---|---|---|
| Seamless rolled rings | Radial-axial rolled rings, contoured rings, gear ring blanks, slewing rings | OD 50 to 6,000 mm | 6 m, 3 m and 1 m ring mills, upset-and-punch below mill range |
| Forged rings | Upset and punched rings, retaining rings, valve seat rings | to 30 t single piece | 6,300 t press |
| Forged flanges | Weld neck, blind, slip-on, socket weld, lap joint, orifice, long weld neck | to 5,000 mm machined diameter | 5,000 mm swing vertical lathe |
| Forged bar and blocks | Round, flat and square bar, die and mould blocks | to 14,000 mm turned length | C61160 horizontal lathe |
| Discs and tube sheets | Forged disc, tube sheet, cover, blank | to 5,000 mm machined diameter | 5,000 mm swing vertical lathe |
| Hollow forgings | Hollow bar, sleeve, bushing, cylinder, coupling, heavy-wall pipe section | to 1,600 mm dia x 10,000 mm bored | CNC deep-hole drilling machine |
| Shafts and spindles | Stepped, gear, pinion and eccentric shafts, rolls, rotors | to 14,000 mm between centres, 15 m vertical quench | Horizontal lathe and well furnaces |
| Valve and wellhead parts | Bodies, bonnets, stems, seat rings, spools, nozzles, manifolds | to drawing | Machine shop capacity |
| Single piece weight | All forms | to 30,000 kg | 60 t maximum heat size, 6,300 t press |

Minimum order is 10 kg with no minimum piece count, so a one-off replacement part is
quotable. Lead time runs 20 to 60 days from order confirmation. Forgings are supplied
as-forged with allowance, proof-machined for volumetric inspection, or finish-machined to
drawing.

## Applications

Urea and fertiliser plant: high pressure stripper internals and ferrules, the outer layer
of bimetallic tube, carbamate condenser and decomposer components, reactor coil parts, and
the forged flanges, tube sheets and nozzles that go with them. Heating coils and pipe in
NPK plants sit in the same category.

Nitric acid and chemical process plant: cooler and condenser components, including units
cooled with polluted cooling water, plus separator and heat exchanger parts where
resistance to inorganic acid attack governs the material choice.

Wider process industry: published application lists for 1.4466 extend to the paper and
cellulose industry, the nitrogen industry, pharmaceutical production and petrochemical
plant. Buyers also specify it for seawater desalination parts, compressor components, and
valve bodies, stems and seat rings for ball, gate, globe, check and plug valves in
aggressive service.

Suitability under a particular pressure code, whether PED, ASME or GB 150, depends on
approvals held for the grade and for the manufacturer, not on the analysis alone. The
works holds CCS, BV, DNV, LR and NK classification society approvals.

## Production route

1. Drawing review. Forgeability, ruling section, machining allowance and the
   solution-anneal route are checked before pricing. If the geometry is awkward to forge
   we say so and propose an alternative.
2. Melting and refining. Electric arc furnace, ladle furnace, then vacuum oxygen
   decarburisation on a 30 t or 60 t unit to bring carbon down and hold nitrogen inside
   the 0.10 to 0.16 % window this grade requires. Maximum heat size 60 t.
3. Open-die forging. Billet soaked to about 1150 C, then upset and drawn on a 6,300 t,
   4,000 t or 2,000 t press with reheats as needed, finishing not below 850 C.
4. Ring rolling. Ring geometries are pierced and rolled radially and axially on the 6 m,
   3 m or 1 m mill, putting grain flow around the circumference rather than across it.
5. Solution annealing. Solution anneal to the specified range, soak by section thickness,
   then rapid cooling in water. Long shafts quench vertically in the 15 m well furnaces.
6. Testing. Optical emission spectrometry and infrared carbon and sulphur analysis,
   tensile on 600 kN and 300 kN machines, Charpy V-notch to minus 60 C, ultrasonic to
   ASTM A388 or EN 10228-3, magnetic particle to ASTM E709, grain size to ASTM E112.
   ASTM A262, G28 and G48 corrosion tests placed with an accredited third-party
   laboratory.
7. Machining. Rough, proof-machined or finish-machined to drawing on vertical lathes to
   5,000 mm swing, horizontal lathes to 14 m, CNC machines and a deep-hole drill.
8. Certification and despatch. EN 10204 3.1 mill test certificate as standard.
   EN 10204 3.2 witnessed by BV, DNV, LR, SGS, TUV or your own inspector on request, with
   heat-treatment charts, NDT reports, dimensional reports and PMI records.

## Questions and answers

**What is A182 F310MoLN?**
The ASTM A182 forging grade for UNS S31050, a fully austenitic 25 % Cr, 22 % Ni stainless
steel modified with molybdenum and nitrogen and held to extra low carbon, developed for
urea and ammonium carbamate service. Also designated EN 1.4466, X1CrNiMoN25-22-2,
AISI 310MoLN, BS 725LN and UREA 25.22.2.

**What is the tensile strength of A182 F310MoLN?**
ASTM A182 requires 78 ksi (540 MPa) tensile minimum and 37 ksi (255 MPa) yield minimum,
with 25 % elongation and 40 % reduction of area. Published typical values for solution
annealed product are 540 to 740 MPa tensile, about 250 MPa proof strength and 40 %
elongation.

**Is A182 F310MoLN the same as UNS S31050 and EN 1.4466?**
Same alloy, different standards, and the limits are not identical. EN 1.4466 caps carbon
at 0.020 % and molybdenum at 2.00-2.50 %, while ASTM A182 F310MoLN allows carbon to
0.030 % and molybdenum to 3.00 %. A separate cross-reference source states the ASTM ranges
differently again. Order against a named standard and edition.

**Why F310MoLN rather than 316L in urea plants?**
UNS S31050 was developed for urea stripper tubes. It resists urea and carbamate at high
pressure and temperature, resists intergranular corrosion after welding, and is
considerably more resistant to crevice corrosion than 316L. Higher nickel also gives
somewhat better resistance to chloride stress corrosion cracking, which affects 304 and
316 above roughly 60 C.

**What heat treatment does it receive?**
Solution anneal followed by rapid cooling in water. Sources differ on the range:
1050-1100 C with a 5 to 15 minute soak is carried by supplier data for this grade, while
other datasheets give a wider band reaching about 1150 C. The customer specification
governs. The quench cannot be slow, because precipitation through the intermediate band
removes the corrosion performance the grade is bought for.

**Can A182 F310MoLN be welded?**
Yes, and weldability is described as good. Welding is done without preheating and normally
needs no subsequent heat treatment, because the extra low carbon prevents sensitisation.
Low thermal conductivity and high thermal expansion mean heat input and distortion need
control, and filler selection should be confirmed with your welding engineer for the
specific service.

**Do you melt this grade in house, or buy billet?**
Melted on site. A 25 t electric arc furnace, 25 t and 50 t ladle furnaces and 30 t and
60 t vacuum oxygen decarburisation units, with a 60 t maximum heat. VOD is what allows
extra low carbon and controlled nitrogen in the same heat. The certificate traces the part
to its melt number instead of stopping at a purchased billet.

**What is the minimum order quantity?**
10 kg, with no minimum piece count, because the limit is weight rather than quantity. A
single one-off part is quotable. In practice small parts get grouped into a batch to share
furnace and setup time, so quantity still moves the unit price even though it does not
decide whether the job can be taken.

**What is the largest ring you can roll in this grade?**
6,000 mm outside diameter on the 6 m radial-axial mill, with 3 m and 1 m mills for smaller
sizes and an upset-and-punch route from 50 mm OD. Heaviest single forging is 30 tonnes on
a 6,300 t press. Downstream sets the practical limits: vertical lathes machine to
5,000 mm swing, horizontal lathes to 14 m between centres.

**Can you carry out intergranular corrosion testing?**
Yes, through an accredited third-party laboratory, with the report issued alongside the
mill certificate. ASTM A262 and ASTM G28 intergranular corrosion tests and ASTM G48
pitting tests are placed outside. Chemical analysis, tensile, impact to minus 60 C,
ultrasonic, magnetic particle and metallography run in the on-site laboratory.

**What certificates are available?**
EN 10204 3.1 as standard with every order. EN 10204 3.2 witnessed by BV, DNV, LR, SGS, TUV
or your own inspector on request. Flag 3.2 at enquiry stage so witness points go into the
schedule rather than getting added late. The works holds CCS, BV, DNV, LR and NK class
approvals.

**What information do you need to quote?**
Six items: the grade or specification, the dimensions or a drawing in PDF, DWG, DXF or
STEP, the quantity and expected repeat volume, the delivery condition, the heat treatment
and testing requirements, and the certification plus destination port. With those a firm
price usually comes back within two working days.

**Who supplies A182 F310MoLN forgings?**
Jiangyin Jiangnan Metal Co., Ltd., an integrated melting works and open-die forging
factory at No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China,
operating since 1997 with 460 staff and holding CCS, BV, DNV, LR and NK approvals. Email
sales@steelforgepieces.com or call +86 189 2135 9659.

## Enquiry checklist

| # | Item | Example for this grade |
|---|---|---|
| 1 | Material grade or specification | ASTM A182 F310MoLN / UNS S31050 |
| 2 | Dimensions, or a drawing in PDF, DWG, DXF or STEP | OD 1200 x ID 900 x H 260 mm |
| 3 | Quantity and expected repeat volume | 6 pcs, about twice per year |
| 4 | Delivery condition | Proof-machined for ultrasonic inspection |
| 5 | Heat treatment and testing | Solution annealed, UT to ASTM A388, ASTM A262 Practice E |
| 6 | Certification and destination port | EN 10204 3.2 witnessed by DNV, Rotterdam |

## Related grades

A182 F44, 904L, Sanicro 28, Alloy 24, A182 F316, A182 F347, A182 F321, A182 F51, A182 F53,
A182 F55, A182 F61, Alloy 31, Incoloy 825, Incoloy 926. More than 300 grades are forged at
this works across carbon and low-alloy steel, stainless and duplex stainless, tool and die
steel, and nickel-based alloys and superalloys. The plant works to customer chemistry
where a grade is not listed.

---

Property data on this page is compiled from published ASTM A182 / A182M F310MoLN and
EN 1.4466 datasheets and is given for enquiry and preliminary design. Where sources
disagree, both figures are shown. The EN 10204 certificate issued with the forging is the
governing document.

Copyright 1997 to 2026 Jiangyin Jiangnan Metal Co., Ltd. Integrated melting works and
open-die forging factory, Jiangyin, Jiangsu, China.
