# 1.4854 forgings — X6NiCrSiNCe35-25 / UNS S35315

Source: https://www.steelforgepieces.com/Stainless-Steel/1.4854.html
Supplier: Jiangyin Jiangnan Metal Co., Ltd., open-die forging works, Jiangyin, Jiangsu, China
Contact: sales@steelforgepieces.com | +86 189 2135 9659
Last reviewed: 26 September 2026

## Summary

1.4854 is the EN material number for X6NiCrSiNCe35-25, an austenitic heat-resisting
chromium-nickel steel of about 25 % Cr and 35 % Ni, alloyed with nitrogen and carrying a
cerium addition of 0.03 to 0.08 %. Its UNS number is S35315. It is specified in EN 10095,
the European standard for heat resisting steels and nickel alloys, which marks it as a
patented steel grade.

The grade is used in furnaces and hot-gas service, not in seawater or acid. EN 10095 gives a
maximum application temperature in air of 1170 °C. Metalcor credits it with good creep
rupture strength, very good high-temperature corrosion resistance and scaling resistance to
1100 °C, with heat treatment furnaces as the application. Alleima attributes the oxidation
resistance to the silicon content together with the rare earth addition, which also improves
scale adhesion during temperature cycling.

Jiangyin Jiangnan Metal forges this grade to order: minimum 10 kg with no minimum piece
count, single pieces to 30 tonnes, rolled rings to 6,000 mm outside diameter, EN 10204 3.1
certification as standard and 3.2 witnessed on request.

## Designations

| System | Designation |
|---|---|
| EN material number | 1.4854 |
| EN steel name | X6NiCrSiNCe35-25 |
| UNS | S35315 |
| Common trade name | 353 MA (Alleima records this as a trademark owned by Outokumpu OY) |
| Material standard | EN 10095 |
| Tube product standards quoted by Alleima | ASTM A312, EN 10297-2 |

Forgings are normally ordered to EN 10095 chemistry and heat treatment, with dimensions,
testing and acceptance set by the purchase specification or the drawing.

## Chemical composition, % by mass, balance iron

| Element | EN 10095 range | Alleima nominal |
|---|---|---|
| C | 0.04 to 0.08 | 0.07 |
| Si | 1.20 to 2.00 | 1.6 |
| Mn | 2.00 max | 1.5 |
| P | 0.040 max | 0.040 max |
| S | 0.015 max | 0.015 max |
| Cr | 24.00 to 26.00 | 25 |
| Ni | 34.00 to 36.00 | 35 |
| N | 0.12 to 0.20 | 0.16 |
| Ce | 0.03 to 0.08 | 0.05 |

Alleima notes that other rare earth metals should be counted with the cerium, because the
addition is made as misch metal containing about 50 % cerium. Metalcor works to a tighter
Si limit of 1.30 % max and N 0.17 % max on its own supply.

## Mechanical properties at 20 °C, solution annealed

| Property | EN 10095 | Alleima, seamless tube |
|---|---|---|
| Rp0.2 | 300 N/mm² min | 300 MPa min (44 ksi) |
| Rp1.0 | 340 N/mm² min | 340 MPa min (49 ksi) |
| Rm | 650 to 850 N/mm² | 650 MPa min (94 ksi) |
| Elongation A | 40 % min | 40 % min, A2" 35 % min |
| Hardness | 210 HB max | about 160 HV |
| Modulus of elasticity | not specified | 190 GPa |

EN 10095 lists these values for flat products to 75 mm, bars to 160 mm and rods to 25 mm in
condition +AT. For rods only the tensile strength applies. For sections and bars of 35 mm and
under with a final cold deformation, the standard permits hardness 100 units higher or
tensile strength 200 N/mm² higher, with elongation down to 20 %.

## Strength at temperature (Alleima)

| Temperature, °C | Rp0.2, MPa | Rp1.0, MPa | Rm, MPa |
|---|---|---|---|
| 100 | 228 | 261 | 536 |
| 200 | 195 | 223 | 498 |
| 300 | 166 | 190 | 470 |
| 400 | 152 | 173 | 444 |
| 500 | 143 | 163 | 437 |
| 600 | 138 | 159 | 422 |

## Creep strength, estimated average values, MPa

| Temperature, °C | 1 % in 10,000 h | 1 % in 100,000 h | Rupture in 10,000 h | Rupture in 100,000 h |
|---|---|---|---|---|
| 600 | 88 | 52 | 127 | 80 |
| 700 | 35 | 21 | 56 | 36 |
| 800 | 15 | 9.7 | 28 | 18 |
| 900 | 8 | 5.1 | 15 | 9.2 |
| 1000 | 4.5 | 3.0 | 8 | 4.8 |
| 1100 | 2.7 | 1.8 | 4.5 | 2.9 |

Values to 1000 °C follow the EN 10095 creep tables for condition +AT. The 1100 °C row comes
from the Alleima datasheet. These are average values for grade comparison, not design
allowables for a specific forging.

## Physical properties (Alleima)

| Property | At 20 °C | At temperature |
|---|---|---|
| Density | 7.9 g/cm³ | — |
| Thermal conductivity | 11 W/m °C | 20 at 500 °C, 27 at 1000 °C |
| Specific heat capacity | 480 J/kg °C | 590 at 500 °C, 665 at 1000 °C |
| Mean thermal expansion | 15.5 × 10⁻⁶ /°C (20-100 °C) | 18 × 10⁻⁶ /°C (20-1000 °C) |
| Modulus of elasticity | 190 GPa | 155 GPa at 600 °C, 130 GPa at 1000 °C |
| Electrical resistivity | 1.00 µΩ·m | 1.30 µΩ·m at 1000 °C |

## Corrosion behaviour at temperature

Oxidation: high silicon plus the rare earth metal addition gives very high oxidation
resistance, and the rare earth addition improves scale adhesion under thermal cycling
(Alleima).

Carburisation and nitrogen pick-up: the dense chromium oxide and the 35 % nickel give good
resistance. Alleima's rate-constant data shows the grade resisting cyclic
carburising-oxidising conditions better than the alloys tested against it.

Nitriding: in nitrogen pick-up tests in cracked ammonia, Alleima reports resistance similar
to Alloy 601.

Sulphur: high-nickel alloys are generally sensitive to sulphur attack at temperature, though
under oxidising conditions a protective oxide forms and improves resistance (Alleima).
Sulphidising service should be stated at enquiry.

## Service temperature

EN 10095 gives 1170 °C maximum application temperature in air, on the basis that scaling loss
does not exceed 1 g/m²h. Metalcor states scaling resistance to 1100 °C. Alleima gives
approximately 1175 °C maximum operating temperature for its tube, with oxidation data measured
at 1150 °C. These describe scaling resistance; for a loaded component the creep table governs.

## Heat treatment, welding and forming

| Operation | Recommendation |
|---|---|
| Solution annealing | 1100 to 1150 °C, sufficiently rapid cooling in water or air (EN 10095, condition +AT). Alleima gives 1100 to 1200 °C for 5 to 20 minutes, rapid cooling in air or water. |
| Stress relieving | 1000 to 1100 °C for 10 to 15 minutes, cooled in air (Alleima). |
| Welding process | Good weldability. TIG/GTAW first choice; MIG/GMAW and MMA/SMAW also suitable. |
| Filler metals | ISO 18274 S Ni 6082 / AWS A5.14 ERNiCr-3 for TIG and MIG; ISO 14172 E Ni 6182 / AWS A5.11 ENiCrFe-3 for MMA. Metalcor also lists 1.4854 as a matching filler. |
| Welding parameters | Heat input below 1.0 kJ/mm, interpass temperature below 100 °C. Plan the weld sequence for distortion. Solution annealing after welding is an option where residual stress matters. |
| Cold bending | Higher deformation forces than conventional stainless steels. Annealing after bending not normally required, judged against degree of bending and service conditions. |

## Applications

Published applications:

- Ethylene furnace radiant cracking tubes
- EDC furnace tubes
- Recuperator tubes in metallurgical waste heat recovery systems
- Heat treatment furnace hardware: muffle tubes, radiant tubes, thermocouple protection
  tubes, burner components, furnace rollers
- Recuperator tubes in chemical waste and sewage sludge incineration

Forged shapes most often ordered from us in this grade: furnace roller journals, hubs and end
caps; radiant tube and retort flanges; recuperator tube sheets and covers; burner nozzles and
sleeves; rolled rings for furnace and kiln hardware; fan and rotor hubs for hot gas
circulation; bar for machined furnace fixtures.

Not a seawater, sour service or strong acid grade. For those duties the relevant grades are
super duplex A182 F55 and A182 F53, duplex A182 F51, and super austenitic A182 F44 and 904L.

## Product forms supplied

Seamless rolled rings, forged rings, forged flanges, forged discs and tube sheets, forged
shafts and rolls, hollow cylinders, sleeves and bushings, forged bar and blocks, and machined
components such as bodies, blocks, nozzles and seat rings.

## Manufacturing route at Jiangyin Jiangnan Metal

Steel is melted on site rather than purchased as billet, so the certificate traces back to the
melt number.

| Step | Equipment |
|---|---|
| Melting and refining | 25 t electric arc furnace; 25 t and 50 t ladle furnaces; 30 t and 60 t vacuum oxygen decarburisation. Maximum heat size 60 t. |
| Remelting where specified | 3 t and 6 t protective-atmosphere electroslag remelting; 3 t vacuum induction melting; 6 t vacuum arc remelting. |
| Forging | 6,300 t, 4,000 t and 2,000 t hydraulic open-die presses; hammers 5 t, 3 t, 2 t, 1 t, 750 kg. Heaviest single forging 30 t. |
| Ring rolling | Radial-axial mills, maximum OD 6,000 mm, 3,000 mm and 1,000 mm. |
| Heat treatment | 14 furnaces, including three high-temperature car-bottom furnaces RTX-12-350KW, chamber 3,500 × 1,300 × 1,100 mm, and two 15 m well-type furnaces. |
| Machining | Vertical lathes to 5,000 mm swing; horizontal lathes to 14 m between centres; CNC deep-hole drilling to 1,600 × 10,000 mm. |

## Testing and certification

| Test | Equipment or route | Standard |
|---|---|---|
| Chemical analysis | SPECTROTEST TXC25 optical emission spectrometer | ASTM E415 |
| Carbon and sulphur | HIR-9440D infrared analyser | ASTM E1019 |
| Alloy verification | X-Mwt3000TX handheld analyser | Positive material identification |
| Tensile | WE-600B 600 kN, WDW-300 | ASTM A370, ISO 6892 |
| Impact | JBN-300 with DWC-60 low-temperature bath | ASTM A370 |
| Ultrasonic | PXUT-3300, USM35XS, CTS-22 | ASTM A388, EN 10228-3 |
| Magnetic particle | CYE-3A | ASTM E709 |
| Grain size and metallography | XJP-6A microscope | ASTM E112 |
| Intergranular corrosion, when specified | Accredited third-party laboratory | ASTM A262, ASTM G28 |

Certification: EN 10204 3.1 as standard; EN 10204 3.2 witnessed by BV, DNV, LR, SGS, TUV or
the customer's inspector on request. Works approvals: CCS, BV, DNV, LR, NK.

## Commercial terms

| Item | Detail |
|---|---|
| Supply basis | Made to order from drawing or specification. Manufacturer, not a stockist. |
| Minimum order | 10 kg, no minimum piece count |
| Quotation | Within 2 working days of a complete enquiry |
| Lead time | 20 to 60 days by material route and testing scope |
| Delivery condition | As-forged, proof-machined or finish-machined |
| Drawing formats | PDF, DWG, DXF, STEP |

## Frequently asked questions

**What is 1.4854 steel?**
The EN material number for X6NiCrSiNCe35-25, an austenitic heat-resisting chromium-nickel
steel of about 25 % Cr and 35 % Ni with nitrogen and 0.03 to 0.08 % cerium. UNS S35315,
specified in EN 10095.

**What is the chemical composition of 1.4854?**
To EN 10095: C 0.04-0.08, Si 1.20-2.00, Mn 2.00 max, P 0.040 max, S 0.015 max, Cr 24.00-26.00,
Ni 34.00-36.00, N 0.12-0.20, Ce 0.03-0.08, balance iron.

**What are the mechanical properties of 1.4854?**
EN 10095: Rp0.2 300 N/mm² min, Rp1.0 340 N/mm² min, Rm 650-850 N/mm², elongation 40 % min,
hardness 210 HB max. Modulus of elasticity 190 GPa at 20 °C.

**What is the maximum service temperature?**
EN 10095 gives 1170 °C in air. Metalcor states scaling resistance to 1100 °C; Alleima gives
approximately 1175 °C for its tube. Under load, creep governs: 100,000 h rupture strength is
36 MPa at 700 °C, 18 MPa at 800 °C, 9.2 MPa at 900 °C, 4.8 MPa at 1000 °C.

**What is 1.4854 used for?**
Ethylene furnace radiant cracking tubes, EDC furnace tubes, metallurgical recuperators, heat
treatment furnace hardware including muffle and radiant tubes, thermocouple protection tubes,
burner components and furnace rollers, and incineration recuperator tubes.

**Is 1.4854 suitable for seawater or acid service?**
No. It is a heat-resisting grade for high-temperature oxidising, carburising and nitriding
atmospheres.

**How is 1.4854 heat treated after forging?**
Solution anneal at 1100 to 1150 °C with rapid cooling in water or air per EN 10095; Alleima
gives 1100 to 1200 °C for 5 to 20 minutes. Stress relieve at 1000 to 1100 °C for 10 to 15
minutes, air cooled.

**Which filler metal is used to weld 1.4854?**
ISO 18274 S Ni 6082 / AWS A5.14 ERNiCr-3 for TIG and MIG; ISO 14172 E Ni 6182 / AWS A5.11
ENiCrFe-3 for MMA. Heat input below 1.0 kJ/mm, interpass below 100 °C.

**How large a ring can you roll?**
Up to 6,000 mm outside diameter on the 6 m radial-axial mill, from OD 50 mm on the
upset-and-punch route. Heaviest single forging 30 tonnes.

**What is the minimum order and lead time?**
10 kg minimum, no minimum piece count. Lead time 20 to 60 days. Quotation within two working
days of a complete enquiry.

## Reference data

Composition, mechanical limits, heat treatment, maximum application temperature and creep
values: EN 10095. Nominal analysis, physical properties, welding and forming data: Alleima
353 MA seamless tube datasheet. Scaling resistance and supplementary hardness data: Metalcor
datasheet 1.4854. The figures that govern an order are those on the mill certificate issued
with the parts.

## Contact

Jiangyin Jiangnan Metal Co., Ltd.
No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China 214423
sales@steelforgepieces.com | +86 189 2135 9659
Monday to Saturday, 08:00 to 17:30 China Standard Time (UTC+8). English and Chinese.
Established 1997. Approvals: CCS, BV, DNV, LR, NK.
