# X2CrNiMoN17-13-5 (EN 1.4439 / AISI 317LMN) Forgings

Supplier: Jiangyin Jiangnan Metal Co., Ltd., open-die forging factory
Address: No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Tel: 0086-189-2135-9659 | Email: sales@steelforgepieces.com
Source page: http://www.steelforgepieces.com/Stainless-Steel/X2CrNiMo17-13-5.html
Last reviewed: 9 October 2026

## Summary

X2CrNiMoN17-13-5, EN steel number 1.4439, AISI 317LMN, UNS S31726, is a low-carbon
nitrogen-alloyed austenitic stainless steel with 16.5-18.5 % Cr, 12.5-14.5 % Ni,
4.0-5.0 % Mo and 0.12-0.22 % N to EN 10088-3. The high molybdenum with the nitrogen
addition gives better pitting and crevice corrosion resistance than 316L or 317L,
and the nitrogen lifts the 0.2 % proof strength to minimum 280 N/mm2 solution annealed.

Jiangyin Jiangnan Metal Co., Ltd. forges 1.4439 rings, seamless rolled rings, flanges,
shafts, discs, sleeves, bushings, tube sheets and bars to drawing, ultrasonically tested
to EN 10228-3, SEP 1921 or ASTM A388, with EN 10204 3.1 or third-party 3.2 certificates.

Name note: the EN 10088 name includes the letter N. X2CrNiMo17-13-5, X2CrNiMoN17.13.5
and X 2 CrNiMoN 17-13-5 all refer to the same grade, 1.4439.

## Chemical composition, % by mass, max unless a range is shown

| Standard | C | Si | Mn | P | S | N | Cr | Mo | Ni | Fe |
|---|---|---|---|---|---|---|---|---|---|---|
| EN 10088-3, X2CrNiMoN17-13-5 (1.4439) | 0.030 | 1.00 | 2.00 | 0.045 | 0.015 | 0.12-0.22 | 16.5-18.5 | 4.0-5.0 | 12.5-14.5 | Bal. |
| UNS S31726, AISI 317LMN | 0.030 | 0.75 | 2.00 | 0.045 | 0.030 | 0.10-0.20 | 17.0-20.0 | 4.0-5.0 | 13.5-17.5 | Bal. |

Sources: BS EN 10088-3 composition tables (BSSA); Sandmeyer Steel Alloy 317LMN
specification sheet. The EN and UNS windows overlap but are not identical.

## Mechanical properties, solution annealed, room temperature, EN 10088-3

| Thickness or diameter | Rp0.2 N/mm2 | Rp1.0 N/mm2 | Rm N/mm2 | Elongation A % | Hardness HB |
|---|---|---|---|---|---|
| up to 160 mm | min 280 | min 315 | 580-800 | min 35 | max 250 |
| over 160 up to 250 mm | min 280 | min 315 | 580-800 | min 30 | max 250 |

Source: BS EN 10088-3:2023 tables for austenitic long products (BSSA). For rods only the
tensile strength values apply. Solution treatment may be omitted where hot working and
cooling meet the property and intergranular corrosion requirements of EN ISO 3651-2.

Typical and elevated-temperature values (Virgamet):
Rm 580-800 MPa, Rp0.2 over 280 MPa, A over 35 %, KV at 20 C over 100 J, under 250 HB.
Rp0.2 at 100/200/300/400 C: 225/185/165/150 MPa.
Modulus at 100/200/300/400/500 C: 194/186/179/172/165 GPa.
ASTM-certified 317LMN plate is quoted lower by Sandmeyer Steel: 205 MPa yield,
550 MPa tensile, 40 % elongation, max 96 HRB.

## Physical properties

| Property | Value |
|---|---|
| Density | 8.0 g/cm3 (0.290 lb/in3) |
| Modulus of elasticity at 20 C | 200 GPa (29.0 x 10^6 psi) |
| Thermal conductivity | about 14 W/m.K |
| Specific heat at 20 C | 500 J/kg.K |
| Electrical resistivity at 20 C | 0.85 micro-ohm.m |
| Thermal expansion 20-100 / 20-300 / 20-500 C | 16.0 / 17.0 / 18.0 x 10^-6 /K |
| Melting range | 1393-1443 C (2540-2630 F) |
| Magnetic response | non-magnetic as annealed |
| Design temperature range, forgings | -10 to +400 C per DIN EN 10222-5:2017 |

Sources: Virgamet, Sandmeyer Steel, Applus+ datasheet for 1.4439. Steelnumber records
that the steel shall not be applied below -196 C metal temperature.

## Equivalents

| System | Designation |
|---|---|
| EN / DIN | X2CrNiMoN17-13-5, 1.4439 |
| AISI / ASTM | 317LMN |
| UNS | S31726, near grades S31725, S31753 |
| AFNOR | Z3CND18-14-05Az |
| China | 022Cr19Ni16Mo5N |
| Trade names | BOEHLER A400, Acidur 4439, BGH 4439, Koro 4439, CLC 17-13-5LN, TP317LMN |
| Nearest lower-Mo EN grades | 1.4434, 1.4438, 1.4429 |

## Standards listing 1.4439

Forgings: DIN EN 10222-5 (stainless steel forgings for pressure purposes),
EN 10272 (stainless steel bars for pressure purposes), AD 2000-Merkblatt W 2.
Other product forms: EN 10088-1/-2/-3/-4/-5, EN 10028-7, EN 10216-5, EN 10297-2,
EN 10217-7, EN 10296-2, EN 10253-3, EN 10253-4.

## Corrosion resistance

Pitting resistance equivalent, PRE = Cr + 3.3Mo + 30N (Sandmeyer Steel):
316 = 25, 317L = 30, 317LM = 34, 904L = 36, 317LMN = 38, 6Mo grades = 48,
Alloy 625 = 52, Alloy C-276 = 69. The more common PREN formula uses a nitrogen
factor of 16 and returns a lower figure, so compare within one formula only.

Suited to sulfuric, hydrochloric, acidic chloride and phosphoric acid service and to
hot organic and fatty acids. Not a first choice for strongly oxidising acids such as
nitric acid. Low carbon allows use in the as-welded condition without chromium carbide
precipitation. Still open to chloride stress corrosion cracking, as all austenitics are.

## Heat treatment and fabrication

Solution annealing 1020-1120 C followed by rapid cooling (other sources give 1000-1150 C).
Cannot be hardened by heat treatment, only by cold work. Avoid dwell between 600 and 900 C.
Machining: work-hardens fast. Sandmeyer turning data, 6 mm depth of cut: 11-16 m/min HSS,
70-80 m/min carbide. Welding by TIG, MIG, MMA, SAW; no post-weld heat treatment required.

## Products supplied in 1.4439

| Form | Typical use |
|---|---|
| Seamless rolled rings, forged rings | pressure vessels, columns, towers, tanks, silos |
| Forged flanges, tube sheets, nozzles, tubes, pipes | heat exchangers, air receivers, piping |
| Forged shafts, spindles, crankshafts | pulp, paper, textile, food plant, scrubbers |
| Forged discs, hubs, blanks, gear blanks | gearboxes, compressors, turbines |
| Forged sleeves, bushings, bars, blocks | crystallisers, process and mechanical equipment |
| Valve bodies, stems, seat rings, bonnets | ball, gate, globe, check, plug valves, wellhead parts |

Melting: EAF + AOD/VOD, ESR on request. NDT: UT to EN 10228-3, SEP 1921 or ASTM A388.
Optional: PMI, Charpy, ASTM A262 or EN ISO 3651-2 IGC, ASTM G48 pitting, ferrite count,
grain size, micrographic examination. Certificates: EN 10204 3.1 or 3.2 (TUV, SGS, BV, LR, ABS).

## Contact

Jiangyin Jiangnan Metal Co., Ltd.
No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Tel 0086-189-2135-9659 | Email sales@steelforgepieces.com
Send drawing or dimensions, grade, standard, quantity, test package and certificate level.
