# X1CrNiMoCuN20-18-7 Forgings (EN 1.4547 / UNS S31254 / A182 F44)

Supplier: Jiangyin Jiangnan Metal Co., Ltd., open-die forging factory
Address: No.1 Chengxiqiao Road, Zhouzhuang Town, Jiangyin City, Jiangsu Province, China
Phone: 0086-189-2135-9659 | Email: sales@steelforgepieces.com
Source page: http://www.steelforgepieces.com/Stainless-Steel/X1CrNiMoCuN20-18-7.html

X1CrNiMoCuN20-18-7 is the EN name, material number 1.4547, of a super-austenitic
stainless steel with about 20% chromium, 18% nickel, 6% molybdenum, 0.7% copper and
0.20% nitrogen. It corresponds to UNS S31254 and, as forged fittings and flanges, to
ASTM A182 grade F44. The trade name 254 SMO is a trademark of Outokumpu OY. The grade
is fully austenitic and non-magnetic; it is not a duplex stainless steel.

Jiangyin Jiangnan Metal Co., Ltd. forges this grade to drawing as rings, seamless
rolled rings, flanges, shafts, discs, sleeves, bushings, tube sheets, nozzles, valve
bodies and round bars.

## Quick reference

| Item | Value |
|---|---|
| EN name / number | X1CrNiMoCuN20-18-7 / 1.4547 |
| UNS | S31254 |
| Forged fittings grade | ASTM A182 F44 |
| Structure | Fully austenitic, non-magnetic, not duplex |
| PREN | 42.5 min (Cr + 3.3Mo + 16N) |
| Proof strength Rp0.2 | 300 MPa min |
| Elongation A | 35% min |
| Hardness | 260 HB max |
| Solution anneal | 1150-1200 C, water quench |
| Hot working range | 982-1149 C |
| Density | 8.0 g/cm3 |

## Chemical composition, weight %

| Specification | C | Si | Mn | P | S | Cr | Ni | Mo | Cu | N |
|---|---|---|---|---|---|---|---|---|---|---|
| EN 1.4547 | 0.020 max | 0.70 max | 1.00 max | 0.030 max | 0.010 max | 19.50-20.50 | 17.50-18.50 | 6.00-7.00 | 0.50-1.00 | 0.18-0.25 |
| UNS S31254 | 0.020 max | 0.80 max | 1.00 max | 0.030 max | 0.010 max | 19.50-20.50 | 17.50-18.50 | 6.00-6.50 | 0.50-1.00 | 0.18-0.25 |
| Nominal | 0.010 | - | - | - | - | 20.0 | 18.0 | 6.1 | 0.7 | 0.20 |

Nitrogen is an alloying element, not a residual: it contributes 16 x %N to the PREN.
Dual EN plus UNS certification requires the overlap, Mo 6.00-6.50% and Si 0.70% max.

## Mechanical properties, solution annealed, 20 C

| Property | Requirement | Typical |
|---|---|---|
| Proof strength Rp0.2 | 300 MPa min | - |
| Tensile strength Rm | 650-850 MPa | 680 MPa |
| Elongation A | 35% min | 50% |
| Hardness | 260 HB max | 210 HB |
| Modulus of elasticity | - | 195 GPa |

Seamless tube to the mill standard: Rp0.2 310 MPa min, Rp1.0 340 MPa min,
Rm 655-850 MPa, A 35% min, 96 HRB max. The grade meets 60 J at -196 C per
EN 13445-2 and EN 10216-5.

Minimum proof strength at temperature:

| Temperature, C | 100 | 200 | 300 | 400 | 500 |
|---|---|---|---|---|---|
| Rp0.2, MPa min | 230 | 190 | 170 | 160 | 148 |
| Rp1.0, MPa min | 270 | 225 | 200 | 190 | 180 |
| Modulus E, GPa | 190 | 182 | 174 | 166 | 158 |

## Physical properties

Density 8.0 g/cm3. Thermal conductivity 10 W/m.C at 20 C, 14 at 200 C, 18 at 400 C.
Specific heat 485 J/kg.C. Mean thermal expansion 16 x 10-6 /C over 30-100 C,
17 x 10-6 over 30-500 C. Non-magnetic in the annealed condition.

## Corrosion behaviour

- Pitting and crevice: PREN 42.5 min. Natural seawater at 60 C, prolonged exposure
  without crevice attack.
- SCC, boiling 25% NaCl pH 1.5, U-bend: no attack at 1000 h; 904L crevice corrosion;
  316 pitting under 150 h.
- SCC, drop evaporation: 425 h to failure, against 225 h for 904L and 105 h for 316.
- Acids: more resistant than 316 in pure sulphuric acid, more resistant than 904L in
  naturally aerated sulphuric acid with 2000 ppm chloride.
- Intergranular: passes ASTM A262 practice E after one hour sensitising at 600-1000 C.

## Forging and heat treatment

Hot work 982-1149 C. Solution anneal 1150-1200 C, water quench. No hardening heat
treatment applies; strength is raised only by cold reduction. Avoid prolonged exposure
between 600 and 1000 C because intermetallic phases precipitate there. Avoid contact
with copper and copper alloys before welding or heat treatment.

Welding filler, over-alloyed nickel base: AWS A5.14 ERNiCrMo-3 or ERNiCrMo-13 for
TIG and MIG; AWS A5.11 ENiCrMo-3 or ENiCrMo-13 for MMA. Heat input below 1.5 kJ/mm,
interpass below 100 C, stringer beads.

## Equivalents

EN 1.4547 = UNS S31254 = ASTM A182 F44 (forged) = GB/T 00Cr20Ni18Mo6CuN =
AFNOR Z1 CNDU 20.18.06AZ (withdrawn). Cast equivalent GX2CrNiMoCuN20-18-6 / 1.4557.
Trade name 254 SMO, trademark of Outokumpu OY.

## Product standards

Open-die forgings EN 10250-4. Forged fittings and flanges ASTM A182 F44.
Forged products ASTM A473. Bar EN 10272, EN 10088-3, ASTM A276, A479.
Plate EN 10088-2, EN 10028-7, ASTM A240. Seamless tube EN 10216-5, ASTM A213, A269,
A312. Offshore NORSOK MDS R11 and R18, IOGP S-563 MDS IR111 and IR118.
Sour service NACE MR0175. ASME BPVC Section VIII Div. 1, approved in seamless pipe form.

Ultrasonic testing is to EN 10228-4, which covers austenitic and austenitic-ferritic
stainless steel forgings. EN 10228-3 covers ferritic and martensitic forgings only and
does not apply to this grade. ASTM A388 where the order specifies it.

## Products supplied

Forged rings and seamless rolled rings; weld-neck and blind flanges; tube sheets and
nozzles; pump, compressor and eccentric shafts; spindles; discs and blanks; sleeves and
bushings; valve bodies, blocks, stems and seat rings; round bar, hollow bar and forged
pipe.

## Typical service

Seawater handling and cooling, cooling water pipework, ballast water and firefighting
systems, desalination and high-pressure reverse osmosis, flue gas desulphurisation
scrubbers, gas cleaning, pulp bleaching, tall oil distillation, petroleum production
components, heat exchangers, hydraulic and instrumentation systems, tanks and pipelines
for high-halide chemicals.

## Melting, testing, certification

EAF plus VOD melting, ESR remelting on request. Product analysis, tensile and Charpy
impact, hardness, ASTM A262 practice E, ASTM G48 on request, ultrasonic to EN 10228-4
or ASTM A388. Certification EN 10204 3.1, or EN 10204 3.2 witnessed by TUV, BV, DNV,
LR or ABS.

## Enquiries

Send drawing or dimensions (OD x ID x height for rings, diameter x length for bars and
shafts), quantity, governing specification, delivery condition, NDT and certification
level, destination port.

Jiangyin Jiangnan Metal Co., Ltd. | 0086-189-2135-9659 | sales@steelforgepieces.com
